Gebruiksaanwijzing /service van het product LCD-1900VR van de fabrikant Tote Vision
Ga naar pagina of 20
.
.
2 Operating Instructions Thank you for purchasing this high - resolution multi - scan color monitor. Please read this guide thoroughly before installation.
3 Safety Precautions This monitor is manufactured and tested on the principle that the user ’ s safety comes first. However, i mproper use or installation may not only damage the monitor but endanger the user as well. As a safety precaution, go over the following WARNINGS carefully before installation, and keep this guide handy.
4 Care and Maintenance Care l Avoid exposing your monitor directly to sunlight or other heat sources. Place your monitor away from the sun to re duce glare. l Put your monitor in a well - ventilated area. Do not place anything heavy on top of your monitor.
5 CHAPTER 1 Introduction BEFORE INSTALLING YO UR MONITOR Read this manual cover to cover. PAY ATTENTION to all WARNING and CAUTIONS DO NOT use computer components not recommend by the manufacture Do not attempt to service the m onitor your self.
6 FACTORY - PRESET MODES Table 1 shows standard video mode setting that has be en pre - adjusted at the factory for accurate video display. These setting are stored in the monitor's memory Table 1. Factory - Preset Modes PC mode Mode Resolution H - Freq.
9 l LCD - 1900V R 19” LCD 8U Rack Display Monit or Overall Dimension (HxWxD): 394.5 x 436 x 62 mm Effective Display area (H/V): 376.32 x 301.56 mm Display colors: 16.7M colors Scan Frequencies: Horizontal 31.47K to 80KHz Vertical 60Hz to 75Hz Number of Pixels: 1280x1024 pixels Pixel pitch : 0.
10 Operations: User Controls On/Off Power Button , +/ - and Up/down keys On Screen Display Auto adjustment, Brightness, contrast color temperature, Hue, Tint, Source select, PIP setup H - position, V .
11 Chapter 2 P RODUCT P ACKAGE Open the shipping carton and check the contents. If any items are missing or da maged, contact your dealer immediately. The package should include the following items l Analog Color TFT LCD Monitor l Accessory Box: 1. VGA cable x 1 2.
12 C ONTROL F UNCTIONS The Monitor control functions are located on the lower center of the front view side. They are shown in the figure below and described in the following paragraphs. The control key description 1. : Power Switch 2. - : Decrement 3.
13 DESCRIPTION 1. : Power switch Use the power switch to turn ON or OFF po wer. We recommend turning your system power on first, then the LCD monitor. 2. - & + : decrement or increment the value The two keys are decrement or increment the value or enter into the sub - menu.
14 CHAPTER 3 A DJUSTING THE MONITOR VGA OSD main screen 1024x768 48.5K 60.2 VER XGA - KDC45 - 5100 Auto Adjustment - Execute + 3.
15 1. Each time, when pressing the menu key, the screen will show as above. You can see the 3 mark that mean s the selected item. Then you can change the setting through + or - .key. 2. Pressing Sel key to move the arrow down or up. If the selected item has many option to choose, press – or + to enter into the sub - menu.
16 Co lor balance: the monitor do the white balance automatically. Intensity R: Adjust the R color intensity, the range is from 0 to 63 Intensity G: Adjust the G color intensity, the range is from 0 t.
17 Geometry setup § W e provide Pixel Clock, Phase, H Position, V Position, OSD H Position, OSD V Position and Txt/Gft option to change. § Pixel Clock: Adjust the viewing screen size. The range is from 0 to 99 Phase: Adjust phase tracking to reduce the display flicker.
18 Note: The PIP function is only valid on video on VGA screen. We can ’ t support video on video screen Speaker volume control § We provide Volume, Bass, Treble, Mute and PIP audio for audio s etup. § Volume: Adjust the speaker volume. The range is from 0 to 32.
19 Chapter 4 VIDEO ADJUSTMENT Video OSD Screen NTSC 15.7K 60.2 VER XGA - KDC45 - 5100 1. Each time, when pressing the menu key, the screen will show as above. You can see th e 3 mark, that means the selected item Then you can change the setting through + or - .
20 § Adjust the screen contrast value. The range is from 0 to 127 Intensity adjustment § Adjust the screen intensity value. The range is from 0 to 255 Tint adjustment § Adjust the scr een Tint value. The range is from 0 to 127 Hue adjustment § Adjust the screen Hue value.
21 Appendix Troubleshooting Procedures This LCD Monitor was pre - adjusted in the factory with standard VGA timing. Due to output timing differences among various VGA cards, you may initially experience an uns table or unclear display when a new display mode or new VGA card is selected .
Een belangrijk punt na aankoop van elk apparaat Tote Vision LCD-1900VR (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Tote Vision LCD-1900VR heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Tote Vision LCD-1900VR vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Tote Vision LCD-1900VR leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Tote Vision LCD-1900VR krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Tote Vision LCD-1900VR bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Tote Vision LCD-1900VR kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Tote Vision LCD-1900VR . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
