Gebruiksaanwijzing /service van het product WBS510 van de fabrikant TP-Link
Ga naar pagina of 21
I nstallation Guide Outdoor Wireless Base Station WBS210 / WBS510 C OPY RIGHT & TRADEMARKS is a register ed trademark of TP -LINK TECHNOLOGIES C O., L TD . Other brands and product names are trademarks or register ed trademarks of their respective holders.
C ontents Overview . Package Contents . Panel Layout Hardwar e Installation Connect cables Mount Antenna Power On Lightning and ESD Pr otection Specification FA Q 1 1 2 3 4 5 7 8 15 16 9 Config uration with P harOS Log in to the PharOS Configure the Base Station .
Overview TP-LINK's Outdoor Wireless Base Stations of the Phar os series products are designed f or outdoor wireless network solutions, aiming at long-distance transmission and large coverage of wireless network .
The panel of Base Station: Panel Layout RESET Shielded Ethernet Port LAN1 Shielded Ethernet Port LAN0(POE IN) Grounding Terminal 2 AP/AP Router mode: All four LEDs remain solid . Client/Bridge/Repeater/AP Client Router mode: The more lit LEDs indicate the better wireless sig nal strength.
Passive PoE Adapter Hardw are Installation 3 The Outdoor Wireless Base Stations require external antenna that corresponds to your network environment; a dish antenna for Point-to-Point (PtP) bridge environment, a sector antenna for Point-to-MultiPoint (PtMP) environment, or a columnar antenna for Hotspot environment.
4 Affix the waterproof rubber insert to the underside of the device for waterproofing and replace the cover until it firmly locks into place. Use an adequate Ethernet cable (Lenth up to 60m) to connect the LAN0 (POE IN) port. Shielded CAT5e (or above) cable with an integrated ground wire is recommended.
Attach the protective cap. Push and slide the protective cap down over the Base Station until it firmly locks into place. Align the mounting tabs on the back of the Base Station with the four slots of the mounting bracket. Push and slide the Base Station downward until it locks into place.
6 Loosen and completely remove the end of the metal strap by turning the captive screw counterclockwise with a flathead screwdriver. Position the Base Station and wrap the metal strap around the pole.
7 Connect the Ethernet cable from the Base Station to the POE port of the PoE adapter. Connect an Ethernet cable from your LAN device (a computer, router or switch) to the LAN port on the PoE adapter. Connect the power cord to the power port on the PoE adapter and plug it into an electrical outlet.
Lightning and ESD P rotection Use a shielded CAT5e (or above) cable with an integrated grounding wire for connection. If you have the standard CAT5e cable for the connection, use a separate grounding cable to connect the grounding Terminal (GND) to earth ground.
Open a web browser, type http://192.168.0.254 into the address field and press Enter (Windows) or return (Mac). It is recommended to use the latest version of Google Chrome, Firefox or Safari. C onfiguration with PharOS Log in to the PharOS Before accessing the PharOS Web Interface, you need to assign a static IP address 192.
Enter admin for both User Name and Password , then select your Region from the drop-down list. Read and agree the terms of use, then click Login . Change the default User Name and Password to protect your Base Station. Let’s start configuring the Base Staion.
1. Log in to PharOS and go to the Quick Setup page. 2. Operation Mode: Select Access Point and click Next . 3. LAN Settings: Click Next . 4. Wireless AP Settings: a. Create a new SSID (Network name) for your wireless network. b. Select WPA-PSK/WPA2-PSK for the Security method and create a PSK Password to protect your AP.
Point to MultiPoint (PtMP) Configure the Client 12 AP Client Router LAN:192.168.0.254 WAN:Dynamic IP AP Client Router LAN:192.168.0.254 WAN:Dynamic IP AP Client Router LAN:192.168.0.254 WAN:Dynamic IP 1. Log in to PharOS and go to the Quick Setup page.
13 Configure the Access Point Configure the AP Client Router (CPEs) 1. Log in to PharOS and go to the Quick Setup page. 2. Operation Mode: Select Access Point and click Next . 3. LAN Settings: Set the IP Address to the same subnet with the root AP or router that you want to connect to, and click Next.
14 Hotspot Configure the Access Point Smartphone Laptop Tablet Access Point Hotspot is used to provide Internet access to wireless devices such as smartphones, tablets and laptops. Typically, columnar antennas are used in this environment. 1. Log in to PharOS and go to the Quick Setup page.
Specification H ardware features Wireless features Interface Dimensions Models Maximum Transmit Power 2 Operating Frequency 2 802.11 Standards Power Supply ESD Protection 1 Lightning Protection 1 Oper.
FA Q How to restore the Base Station to its factory default settings? With the Base Station powered on, press and hold the RESET button on the Base Station or the Remote Reset button on the passive PoE adapter for about 8 seconds until the Wireless Signal Strength LEDs flash.
2. Click Start , the PharOS will begin to analyze the power of frequency . Observe the curves for a period of time, and then click stop. Note that the relatively low and continuous part of the average curve indicates less radio noise. Here, we use the figure below as an example.
FC C ST A TEMENT CE M ark W arnin g IC ST A TEMENT Safety Information This equipment has been tested and found to comply with the limits f or a Class A digital device, pursuant to part 15 of the FCC Rules.
NC C Notice & BSMI Notic e 注意！ 安全諮詢及注意事項 依據 低功率電波輻射性電機管理辦法 第十二 條 經型式認證合格之低功率射頻電 機 ，非經許 可 ，.
Een belangrijk punt na aankoop van elk apparaat TP-Link WBS510 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen TP-Link WBS510 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens TP-Link WBS510 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding TP-Link WBS510 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over TP-Link WBS510 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van TP-Link WBS510 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de TP-Link WBS510 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met TP-Link WBS510 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
