Gebruiksaanwijzing /service van het product 10530 van de fabrikant Troy-Bilt
Ga naar pagina of 32
PRINTED IN U .S.A. Oper ator’ s Man ual IMPOR T ANT : READ SAFETY R ULES AND INSTR UCTIONS CAREFULL Y WARNING: This unit is equipped with an inter nal combustion engine and should no t be us ed on o.
2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Ma nual is an important part of your new snow thrower. It will help you assemble, prepare and maintain the unit for best performance.
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES This symbol points out import ant safety instructions , which if not followed, co uld endanger the personal safety and/or proper ty of yourself and others. Re ad and follow all instructi ons in th is manual before attempting to operate this machine.
4 4. Never operate with a missing or damaged chute assembly. Keep al l safety devices in place and working. 5. Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas. 6. Do not ope rate machine whil e under the i nfluence of alcohol or drugs.
5 SECTION 2: ASSEMBLING YOUR SNOW THROWER NOTE: All references to right or left side of the snow thrower are de termined from behind th e unit in the operating posit ion. The “operator ’s position” is defin ed as standing direct ly behind the snow thrower, facing the handle panel.
6 Figure 3 Attaching Chute Assembly (Hardw are Group A) • Place chut e assemb ly over chut e opening, with the opening in the ch ute assembly fac ing the front of the unit. • Place chute fl ange keeper s beneath lip of chu te assembly, with the flat side of chut e flange keeper facing downward.
7 Routing Chute Tilt Cables • If not already ro uted, slip the cables that run from beneath the handle panel to the chute assembly through the cab le guide located on top of the engine housing.
8 Figure 8 Auger Control The auger cont rol is located on the left handle. Squeeze th e auger control to e ngage the augers. Release to stop the snow throwing actio n. The drive control must also be released in order t o stop the auger. IMPORT ANT: Refe r to Auger Control Test on page 10 prior to operating your sn ow thrower.
9 SECTION 4: OPERATING YOUR SNOW THROWER Before Starting WARNING: Read, underst and, and follow all instructions and warnings on the machine and in this manual before operating. Gas And Oil Fill-up Service the engin e with gasoline and oil as instructed in the separ ate engine manual pa cked with your snow thrower.
10 • As engine warms up, rotate choke knob slowly to OFF positio n. If engine falters, return to FULL choke, then slowly m ove to OF F position . T o Stop Engine • Run engine for a few minutes before st opping to help dry off any moisture on the engine.
11 • Repeat Auger Contr ol Test to verify proper adjustment has been achieved . Repeat the previous steps to provide more slack in the cable, if necessary. T o Engage Wheel Drive • With the engine run ning near top speed, move the shift lever into one of the six FORWARD positions or two REVERSE positions.
12 cable) from the drive actu ator bracket. Se e Figure 9. • Push the cab le coupler throu gh the end of the spring to expose the lock nu t. See Figure 10. • Thread the lock nut ou tward (down the coupler) three full turns to provide more slack in the cable and reattach th e spring to the bracket.
13 NOTE: If the tire pressure is n ot equal on both sides, the unit may pull to one side or the ot her. WARNING: Under any circumstance do not exceed manufactur er’s recommended psi.
14 SECTION 6: MAINTAINING YOUR SNOW THROWER WARNING: Before lubricatin g, repairing, or inspecting, disengag e all controls and stop engine. Wait unt il all moving parts have come to a complete stop. Disconnect the spar k plug wire and ground it against the engine to prevent unint ended starting.
15 Figure 16 IMPORT ANT: Be careful not to allow grea se to get on the drive plate or friction wheel. Drive Control / Auger Control Lock The cams on the ends of the control r ods which interlock the drive and auger controls must be lubricated at least once a season or every 25 hours of operation using a mu lti-purpose automotive grease.
16 Figure 17 • Reassemble the new shave plate, making sure heads of carriage bolts are to the inside of the housing. Tighten securely. Replacing Belts To remove and replace either the auger be lt or the drive belt, follow the step s below and then proceed to the specific steps listed under respective sub-headings.
17 Figure 21 • Remove and replace a uger belt inside belt keepers. • Reassemb le pulley to auger ho using with hex bolt and bell washer (cupped side t oward the pulley). Make sure ke y is in place on shaft and brake puck is seated in the pulley groove.
18 Figure 23 Figure 24 NOTE: If the sprocket fell from the snow thrower while removing the hex shaft, place t he sprocket on the hex shaft. Posi tion the hex hub of th e sprocket toward the friction wheel when sliding th e sprocket on to the hex shaft.
19 SECTION 8: TROUBLESHOOTING NOTE: For repairs beyond th e minor adjustments listed above, co ntact an authorized Tro y-Bilt service dealer. Prob lem Cause Remedy Engine fails to start. 1. Fuel tank empty, or stal e fuel. 2. Blocked fuel line. 3. Choke not in ON position 4.
20 SECTION 9: PARTS LIST FOR MODEL 10530 59 60 24 29 30 20 39 1 3 2 4 5 5 5 7 6 57 25 40 42 18 31 57 25 43 27 13 17 13 9 13 26 34 34 26 32 13 16 10 23 12 13 35 11 37 25 13 19 13 33 14 41 28 15 36 38 4.
21 Model 10530 Ref. No. P art No. P art Description 1. 05244A Bearing Housing 2. 618-0281A Auger Brake Bracket Assembly 3. 684-0090A 16” Impeller Assembly 4. 710-0371 Hex Lock Bolt 5/1 6-18 x.875” 5. 710-0451 Carriage Bolt 5/1 6-18 x .750” 6. 710-0459A Hex Screw, Special 3/8-24 x 1.
22 Model 10530 18 12 76 17 8 16 9 11 45 66 4 35 35 36 45 45 10 18 18 24 73 32 42 5 39 23 34 67 14 51 27 75 71 64 58 22 21 29 13 56 52 37 22 2 33 13 29 18 77 47 49 61 48 15 62 27 51 66 42 3 63 33 87 65.
23 Model 10530 Ref. No. P art No. P art Description 1. 741-0225 He x Flange Bear ing 2. 750-1302A Spacer,.6725 x 1.125 x 2.485 3. 618-0279 Do gg Assembly LH 4. 618-0280 Do gg Assembly RH 5. 618-0282D Drive Shaft Assembly 6. 618-04178 Fricti on Wheel Assembly 7.
24 Model 10530 1 1 2 3 4 5 4 5 19 19 19 19 6 6 7 7 9 9 10 21 13 29 11 24 31 17 27 23 15 26 21 15 14 25 16 18 11 20 15 28 30 15 23 13 21 32 32 A A A A 34 34 35 35 36 37 38 39 40 42 44 8 12 43.
25 Model 10530 Ref. No. P ar t No. P art Description 1. 6 46-0012 Au ger/Drive Cable Assembly 2. 6 84-0053B Lower Chute Directional Control 3. 7 05-5266 Sp lit Chute Directiona l Control Brkt. 4. 7 10-1879 H ex Screw, 3/8-16 x.88” 5. 7 10-1878 H ex Screw, 3/8-16 x 1.
26 Model 10530 Ref. No. Pa r t No. Description 1. 07386 W ashe r 2. 684-0123A Be lt Cov er Bracket Assemb l y 3. 710-0191 Hex Scre w 3/8-24 x 1.25” 4. 710-0237 Hex Scre w 5/16-24 x .625” 5. 710-1008 Se lf-tapping Sems Screw 6. 710-0607 TT Screw 5/16-18 x 0.
27 Model 10530 NO TE: When rebuilding a gearbox assembly , inclu de 3 oz. of Shell Alvania EP Lead-F ree Grease (Par t No . 737-0168). Ref. No. P art No. Description 1. 618-0 246 Housing Asse mbly, RH 2. 618-0 435 Housi ng Assembly, LH 3. 710-1260 A Scre w, 5/16-18 x 0.
28 Ref. No. P art No. Description 1. 710-0 276 Carriage Scre w 2. 710-0 458 Carriage Bolt 5/16-18 x 1.75” 3. 710-0 805 Hex Bo lt 5/16-18 x 1.5” 4. 710-0 895 Hex Scre w 1/4-15 x.750” 5. 710-0 597 Hex Scre w 1/4-20 x 1.00” 6. 712-0 4063 Flange Lock Nut, 5/16-1 8 7.
29 NOTES.
30 NOTES.
31 MANUF A CTURER’S LIMITED COMMERCIAL W ARRANTY FOR: The limited warranty set forth be low is given by Troy-Bilt LLC with respect to new merchan dise used for commercial purposes and purchased and .
32 MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth be low is given by Troy-Bilt LLC with respect to new merchandise purch ased and used in the United States and/or its territo.
Een belangrijk punt na aankoop van elk apparaat Troy-Bilt 10530 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Troy-Bilt 10530 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Troy-Bilt 10530 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Troy-Bilt 10530 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Troy-Bilt 10530 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Troy-Bilt 10530 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Troy-Bilt 10530 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Troy-Bilt 10530 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
