Gebruiksaanwijzing /service van het product MA4100 van de fabrikant TUBE DRIVER
Ga naar pagina of 19
OWNERS MANUAL MA4100 Congratulations Endpanel Layout Features & Specifications Endpanel Layout Installation Troubleshooting Wiring Troubleshooting Power / Ground Troubleshooting Connections Troubl.
The extended use of a high powered audio system may result in hearing loss or damage. While TUBE DRIVER systems are capable of "Concer t Le v el" volumes with incredible accuracy , they are also designed for you to enjoy at more reasonable levels all of the sonic subtleties created by musicians.
1 Power Bandwidth: 5 Hz -50 KHz T otal Harmonic Distortion: 0.2% or less (A-weighted) Input T opology: Balanced Differential Input Sensitivity: 500mV - 12 volts RMS Input Impedance: 10K Ohms Output Im.
Recommended Fuse Rating f o r M A 4100 i s 1 0 0 Amps Y ou will need to install an in-line fuse or circuit breaker in the po wer wire within 18” of the battery . This fuse or cir cuit breaker protects y our vehic le from fire in case the po wer wire shor ts to the vehic le body .
3 W arning! Y ou can mount the MA4100 in any position, even upside-down. However , yo u must maintain pr oper airflo w . Do not install your MA4100 under carpets or enclose it behind airtight panels. In trunk-mounted applications, be sure to provide venting for air circulation.
4 W arning! T o prevent a short to ground, disconnect the negative (-) terminal of the system’s battery before you begin. If the power cable shorts to ground, current will continue to flow until the short is opened, the main fuse blows, the battery explodes, or the wire melts.
5 Follow these simple instructions and ref er to the diagram belo w to make y our speaker connections: • Using at least 16 gauge wire, run wire from the speakers to the amplifier(s) using the same p.
6 Y ou can operate each pair of channels in both stereo and mono (3 channel or tri- mode) at the same time by using highpass filters (bass blockers) on the higher frequency stereo channels, and a lowpass filter (coil) on the subwoofers.
7 Input Jac ks The MA4100 includes both RCA and Mini-Din (balanced) inputs. The supplied RCA connections allow you to use the MA4100 with other brands of audio gear . Our Diff erential RCA inputs provide a dramatic impro v ement in noise reduction ov er standard RCA input types.
8 Input Gain Contr ols There are two Input Gain Controls located on the end panel under the RCA input jacks. These are not v olume controls! These controls match the output signal voltage of the source unit to the amplifier inputs.
HANDCRAFTED IN THE USA By Precision Power POWER CONNECT POWER W ARM UP 9 P o wer Side 1 3 2 1. PO WER A red light indicates that the amplifiier is turned on (After warm-up sequence). 2. W ARM UP A red light indicated that the tubes are warming up. (Refer to Pg.
10 Input/Contr ol Side L- L+ REM R+ R- L- L+ R+ R- FRONT SPEAKER OUTPUTS REAR SPEAKER OUTPUTS FRONT GAIN REAR GAIN FRONT INPUTS L R REAR INPUTS L R BALANCED INPUTS FRONT REAR DIN/RCA DIN/RCA -12dB -12dB H A N D C R A F T E D I N T H E U S A B y P r e c i s i o n P o w e r 8 9 10 11 12 17 5 4 3 26 1.
Do you have 12V at the amplifier ’s connections? 11 No Sound Is the W ARM UP LED illuminated? YES NO YES The warm up cycle can take up to 40 sec., Is there sound after that? NO Y ou’re done Is there signal on the RCA ’s? YES NO Does the amp remote (REM) have 12V? Check all connections.
12 No Sound in One Channel YES Reverse the left and right inputs. Check the pre-amp (RCA/Mini-Din) cables for open connections and make corrections. Did you find open connections? NO Y ou’re done SOUND IS NO W IN... Opposite Channel Problem is in the speaker or speaker wire of the silent channel.
Noises While the Engine is On Alternator whine: This noise changes in frequency with engine RPM. Check for: . Excessive input le vel setting on the amplifier . High resistance in cab ling or corroded and/or loose connections . P olarity of the input cab les If the problem persists, check the whines and pops chec klist below .
Check each side of the amplifier independently to see if the distortion is only on one channel. Is that the case? 14 Noises While the Engine is On or Off System hiss: Distortion: Distortion is garbled sounding music. This can often be caused by a shorted speaker wire.
15 eject VOLUME BASS TREBL E RIGHT LEFT BALANCE TR ACK REVERSE FOWARD 1 2 3 4 8 7 6 5 PPI MAR KET ING DPT Trk 1 Preamp/Equalizer Source Unit Sub Passive Crossover Passive Crossover Tweeter Tweeter Mid.
AMP RCA Rear Right Input DIF. RCA Rear Left Input INPUT ATTENUATION AMP RCA Front Right Input Left Left Right Right RCA Front Left Input MINI-DIN Front Input MINI-DIN Rear Input DIF.
Three-Y ear Limited U .S.A. W arranty This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Een belangrijk punt na aankoop van elk apparaat TUBE DRIVER MA4100 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen TUBE DRIVER MA4100 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens TUBE DRIVER MA4100 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding TUBE DRIVER MA4100 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over TUBE DRIVER MA4100 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van TUBE DRIVER MA4100 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de TUBE DRIVER MA4100 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met TUBE DRIVER MA4100 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
