Gebruiksaanwijzing /service van het product 26XX Series van de fabrikant Ultra Start
Ga naar pagina of 24
Co v er s All 25xx and 26xx Series R emote Star ter/ Alar ms -The system must be placed into Service Mode before any service work is started on the vehicle. It is the sole responsibility of the vehicle owner to ensure that this is done. The manufacturer accepts no liability or responsibility for accidental starting of the vehicle.
T able of Contents INST ALLATION MANUAL REMOTE V EHICLE S T ARTER/ALARM Page 2 Pre-Inst allation Page 3 Components Feature List Pre-Installation Inst allation Procedures Page 4 Wiring Diagrams Page 5-.
R ecommended Pre-Installation Procedures F eature List - Control module - 2 4 button transmitters* - Antenna with built in - 6 pin main harness with dual - Program Button and LED’s 30 amp power inputs.
R ecommended Installa tion Procedures Under Hood Connections - Route the hood pin and tach wire through the firewall into the engine compartment. If possible route the wires through a factory rubber grommet. If drilling a hole through the firewall, BE CAREFUL .
REMOTE V EHICLE S T ARTER/ALARM INST ALLATION MANUAL Page 5 Wiri ng Diagra m 1 3 5 2 4 6 2 1 4 3 6 5 7 8 10 10 10 9 12 12 11 11 14 13 13 4P I N BLUE 30 AMP ST ARTER DISABLE RELA Y - NORMALL Y CONNECTE.
Page 6 INST ALLATION MANUAL REMOTE V EHICLE S T ARTER/ALARM Side View PI N 4 RE D P N 4I WE HI T 4 P IN W HITE P N 3 I W HIT E Note-250ma outputs are low current and are designed to activate relays Gr.
Page 7 REMOTE V EHICLE ST ARTER/ALARM INST ALLATION MANUAL 6-pin Description T est For Wire 1-Y ellow 30amp S tarter Output This wire will test 0volts in of f, accessory and in the ignition position.
Page 8 INST ALLATION MANUAL REMOTE V EHICLE ST ARTER/ALARM 14 Pin Connector Continued F r om Pre vious Page 1-Green Door Lock Door Lock Output - Programmable Menu 1 2-Red 12vlt Output Output For Door Lock Module Only! 3-Blue Door Unlock Door Unlock Output - Programmable Menu 1 4-Pink 2nd Unlock Output when button #2 is pressed twice.
Page 9 REMOTE V EHICLE S T ARTER/ALARM INST ALLATION MANUAL 6 Pin P o w er Connector S t e p1-C onnect All Of the F ollo wing W ir es Y ellow 30amp S tarter Output 12volt s during start position only . Green 30amp Heater Output 12volts in the accessory position off during start and 12volt s during run.
Step 1 - Connect All Of the F ollo wing W ir es 6 Pin P o w er Connector Y ellow 30amp St arter Output 12volts during st art position only . Green 30amp Heater Output 12volts in the accessory position off during st art and 12volt s during the run position.
Manual T ra nsmission “M” Models Never install an automatic transmission remote starter into a manual transmission vehicle!!! Doing so may result in serious injury or death. Do not install remote starters in convertible vehicles! The following wires must be connected In addition to the basic remote starter installation.
Auto T ach Learn 1) T urn the ignition key to the “ON” position. (The park lights will turn on*). 2) S tart the vehicle with the key , The LEDs on the antenna will turn on if a proper t ach signal is detected**, then after 30-35 seconds the p ark lights will flash and the siren will chirp twice to confirm T ach Learn.
Impor tant T ac h Notes T ach Learning the remote st arter is one of the most import ant steps in the inst allation process. Do not tach learn vehicle while the engine is in high idle. T o ensure the best possible tach setting, ensure that the vehicle is at low idle/ normal operating RPM.
Entering Pr ogr am Mode 1) With the ignition in the OFF position, turn the ignition key from “Of f” to “On” 3 times, ON-OFF-ON-OFF-ON within three seconds. (Leave the key in the ON position) 2) Press and release the Program Button located on the antenna.
Quic k Vie w Progr amming * See the following p ages for more det ailed programming instructions. Menu 1 - Press Lock 1 Flash 2 Flashes 3 Flashes 1 Ignition Lock Enabled Lock Only Disabled 2 Siren Chirp T ype 1 T ype 2 All Chirps 3 Lock&Unlock Options Double Unlock 3 second .
Menu 1- User Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Lock Button Setting 1 Ignition Auto Lock 1) Ignition Lock & Unlock Enable 1 Flash/Chirp Doors Lock/Unlock with Ignition key . 2) Ignition Lock Only 2 Flashes/Chirps Doors Lock when ignition is turned ON only .
Menu 1- User Settings .. . continued from pr e vious page Setting 5 Active/Passive Locks 1) No Auto-Lock with Passive Arm 1 Flash/Chirp No auto-lock with passive arming *2) Doors Auto-Lock with Passive Arm 2 Flashes/Chirp s Doors Lock when p assive arming Press & Release the Program Button 5 T imes (Setting 5) Confirmed with 5 LED flashes.
*(Default Settings) Menu 2 - Additional Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Unlock Button Setting 1 Secure V alet Mode - Length of time required to set the syst.
Page 19 Menu 3- Star ter Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Button #3 Setting 1 S pecial Door Lock/Unlock Operations (Factory Alarm Rearm) . 1) T ype 1 1 Flash/chirp Unlock before st art. Lock pulse after st art and on shut down.
Menu 4- T ac h Settings Setting 1 Auto T ach Learn. 1) Perform a System Reset. See p age 15. 2) T urn the ignition key on. (Park lights will turn on). 3) S tart the vehicle, the LEDs on the antenna will come on when a proper t ach signal is detected*.
Page 21 REMOTE V EHICLE S T ARTER/ALARM INST ALLATION MANUAL Step 1 - Within 3 seconds turn the ignition ON-OFF-ON-OFF-ON - Leaving Key ON Step 2 - Press and hold the Program Button - Th e park Lights will turn ON and the siren will chirp once.
87 86 85 87a 30 87 86 85 87a 30 Lock Un lock Ve h i c l e Lock/Unlock Switch T o Control Relay or Actuator Green Fused +12V Blue Ground Ne ga tiv e Type Door Loc ks 250ma Ne ga tiv e Door Loc ks (More T han 250ma) P ositiv e T ype Door Locks Note: When installing relays always use a fused power source.
87 86 85 87a 30 87 86 85 87a 30 Blue Green Lock Un lock V ehicle Lock/Unlock Switch To Actuator Fused +12V x x Cut Cut 87 86 85 87a 30 Ground DIA GNOSTICS 13 87 86 85 87a 30 87 86 85 87a 30 Blue Green.
DIA GNOSTICS If the remote starter does not activate when the st art button is pressed the p ark lights will flash a diagnostic to indicate what shutdown input has been triggered. For example when the start button is pressed the p ark lights flash 3 times slowly .
Een belangrijk punt na aankoop van elk apparaat Ultra Start 26XX Series (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ultra Start 26XX Series heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ultra Start 26XX Series vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ultra Start 26XX Series leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ultra Start 26XX Series krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ultra Start 26XX Series bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ultra Start 26XX Series kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ultra Start 26XX Series . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
