Gebruiksaanwijzing /service van het product PT-500 van de fabrikant Unitech
Ga naar pagina of 33
0 USER’S GUIDE PORTABLE DATA COLLECTION TERMINAL PT - 500 DOCUMENT NUMBER: 350500 - 0010.
1 NOTICE The unit is equipped with a NiMH battery pack. It is possibl e that the customer might receive the battery pack in a discharged (dead) state due to product storage.
2 Table of Content Page Chapter 1 Overview …...………………………… 1 1.1 Technical Specification……………… 2 1.2 Software System…………………….. 2 1.3 Application Development……………. 2 Cha pter 2 Installation 2.1 Power On and Off the PT - 500……… 3 2.
3 Chapter 1 Overview The PT - 500 Portable Data Terminal with built - in barcode scanner is a rugged , compact and lightweight hand - held terminal designed for data collection. It offers many features for efficient barcode reading, keyboard data entry, and data processing.
4 1.1 Technical Specification ?? 8 - bit microprocessor CPU. ?? 64KB ROM. ?? 256KB, 512KB, or 1024KB RAM memory. ?? 32x122 dots graphic LCD, 4 li nes x 20 characters. ?? Low power consumption. Standby 25mA Active 160mA ?? Rechargeable NiMH or 3 disposable AA size alkaline batteries.
5 Chapter 2 Installation 2.1 Power On and Off the PT - 500 Press the Power Key ? located near the bottom left corner to turn the terminal on and off. As a safeguard, the unit can only be turned o ff by pressing the power key ? for at least 3 seconds. 2.
6 Insert the batteries in the positions as shown by the polarity symbols inside compartment 4. Replace the battery cover and mo ve the latch back to the locked (centered) position.
7 When the PT - 500 is switched on and the Lithium battery is discharged, the following low backup battery wa rning message will be displayed on the PT - 500 LCD: In this situation you should upload your data from the PT - 500 to a PC and have the Lithium battery replaced.
8 1 A 2 B 3 C 6 F 5 E 4 D 0 K . L 9 I = J 8 H 7 G + M F3 Y F4 Z # U Ins R , ? Del Q F2 X $ T ? ? F1 W % S / P * O - N Exit Menu Enter (YES) Bksp SP (NO) Caps Edit V Unitech Alpha ? Turn on and off of the terminal. Press ? for 3 seconds to turn off terminal.
9 2.4 Triggering the Scanner Module The PT - 500 can be used with a built - in integrated laser or CCD scanner module. To use the scanner, just point the scanner window at a barcode and press the trigger that activates the scanner.
10 RS - 232 COMPUTER SYSTEM MODEM TELEPHONE LINE PORT MODEM RS232 cable 1 A 2 B 3 C 6 F 5 E 4 D 0 K . L 9 I = J 8 H 7 G + M F3 Y F4 Z # U Ins R , ? Del Q F2 X $ T ? ? F1 W % S / P * O - N Exit Menu Enter (YES) Bksp SP (NO) Caps Edit V Unitech Alpha 2.
11 SPARE POWER MAIN COMM RS485 FRONT SIDE RS232 ON OFF DC9V BACK PT015 RS485 RS232 BOTTOM The cradle also provides selectable data communication to the host computer - either point - to - point RS - 232 or multi - point RS485 connection. The following diagram shows how the cradle works with the PT - 500.
12 COMPUTER RS232 cable DC 9V POINT - TO - POINT SYSTEM PT015 Spare Battery pack COMPUTER SYSTEM RS485 interface MULTI - POINT DC 9V DC 9V DC 9V RS232 Connection RS485 Connection Charging and Communication Cradle 1 A 2 B 3 C 6 F 5 E 4 D 0 K .
13 MAIN Indicates the charging status of the main battery installed in the PT - 500. The glowing Red LED indicates charging is in progress. The glowing Green LED indicates charging is complete. POWER When the power is t urned on, the glowing Green LED indicates the cradle is ready to use.
14 Chapter 3 Operation The operating system of the PT - 500 has 4 different operating modes for different purposes and functions. They are as follows: 1. Ready Mode. ?? Keypad Input will be di splayed on the LCD and sent out though RS232 port. ?? Laser or CCD Scanner Input will be displayed on the LCD and sent out through RS232 port.
15 ?? The PT - 500 can execute user - developed applications under Application Mode. Applications will share the configuration settings and files of the system. After the execution of an application, the PT - 500 retu rns to the Ready Mode. The following sections will guide you through the operation functions and features of the PT - 500.
16 (This example is for units with 1024KB RAM memory. Units with 128, 256, or 512 KB memory will display messages appropria te for their respective memory size.) Hold the power on/off key down for at least 3 seconds. The PT - 500 will shut down. Release the power on/off key and press it again to power on.
17 3.2 System Mode MAIN MENU System Mode is the main window to access other system f unctions and settings. Simply press the [MENU] button on the right - hand top corner under Ready Mode to change to the System Mode display. The Main Menu has six selections from which to choose.
18 terminal. M AIN.EXE is a user application program downloaded to the PT - 500. MAIN.EXE and its internal name (Song Demo v1.00, which is defined in the RESOURCE area of user’s C program) will appear only if you have downloaded the program into the PT - 500.
19 Select [1] to change the tim e Enter the correct time (HH:MM:SS). Press [Enter] to save and exit to previous menu. Press [EXIT] to abort and exit to previous menu. Select [2] to change the date Enter the correct date (MM/DD/YYYY). Press [Enter] to save and exit to previ ous menu.
20 3. COMM MENU Select [3 - COMM] to change the settings of the RS232 port. Press [SP] to change the setting. Press [Enter] to confirm the setting and continue to the next selection. Press [EXIT] to abort the last change and exit to the previous menu.
21 There are four user - definable function keys, F1 to F4. Under Ready Mode, pressing one of them wi ll automatically perform a series of keypad inputs.
22 Use F3 or F4 to either abort or confirm the settings and then return to the previous menu. 6. MISC MENU Select [6 - MISC] to modify Power Auto Features. Select [1] to change Auto PowerOff feature. Select [2] to change Auto Run program. Select [Exit] to return to the previous menu.
23 Press [SP] to select the auto run program from start up. Press [Enter] to save the setting and return to the previous menu. Press [EXIT] to abort and return to the previous menu. 3. DIR MENU Select [3 - DIR] to list files. Files can be data, fonts, or an executable program sa ved in the PT - 500.
24 Press [EXIT] to exit to the previous menu. 5. DIAG MENU Select [5 - DIAG] to diagnose the PT - 500 to determine if there are any hardware problems. Select [1] to diag nose LCD Select [2] to diagnos.
25 3. DIAG COM Before diagnosing, loop back the RS232 port Pin 2 - 3, Pin 7 - 8, and press [ENTER]. The test result will be displayed on the bottom line. 4. DIAG MEM During diagnosis, Memory Bank and Offset values will be displayed. If no problem is encountered, a “PASS” message will be d isplayed and you can exit to the previous menu.
26 Note: Initialization will remove any data and user programs from memory. Please upload any important data and then press [YES] to confirm or [NO] to abort. Select [EXIT] to return to Ready Mode. 3.3 EasyJob Mode Easy Job is an application generator to help the user to define simple data collection tasks for the PT - 500.
27 Left - arrow, right - arrow, and backspace keys can be used for editing. During data input, the user can browse the input data, insert one new record, or delete one existing record.
28 Purge Data can be used to delete all the data records after uploading data to the PC. The PURGE feature will delete all the data records but still retain the data format. Press [YES] to confirm or [NO] to abort. The second line number is the number of data records currently in memory.
29 If ON, the EOF (1A Hex) will be sent at the end of the data record. Field Delimiter , / ; /SPACE/NONE The Field Delimiter will be used to separate the fields in each record. Record Delimiter CRLF /NONE/CR/LF The Record Delimiter will be used to separate the records in one file.
30 If ON, each record will include a time stamp automatically following the data record. The time stamp format will follow the setting defined by Time Style. Field 1 to 16 Data input fields are numbered 1 through 16 (maximum). Each field will h ave its own Prompt, Picture, Min, and Max.
31 x Printable characters. (ASCII code 32 - 126) z Full ASCII characters. % Control character used to append constant string. This character can appear only at the beginni ng of a picture. Min >= 1 , <=Max Minimum length of data input. Max >=Min, <= 40 Maximum length of data input.
32 MAININFO COM Converter SETENV BAT Set the environment ASM BAT Assembly C51 BAT Compiler LNK BAT Linker H <DIR> C Header files C <DIR> C Source files R03 <DIR> Object & Lib fil.
Een belangrijk punt na aankoop van elk apparaat Unitech PT-500 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Unitech PT-500 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Unitech PT-500 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Unitech PT-500 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Unitech PT-500 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Unitech PT-500 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Unitech PT-500 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Unitech PT-500 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
