Gebruiksaanwijzing /service van het product 1610 van de fabrikant Vermont Casting
Ga naar pagina of 40
Homeowner ’ s Installation and Operating Manual For use in the United States and Canada Do Not Discard This Manual: Retain for Future Use 30002850 7/06 Rev . 2 SAFETY NOTICE: IF THIS APPLIANCE IS NOT PROPERL Y INST ALLED, OPERA TED AND MAINT AINED, A HOUSE FIRE MA Y RESUL T .
2 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 This manual describes the installation, operation, and maintenance of the V ermont Castings Defiant Model 1610 non-catalytic wood burning heater . This heater meets the U.S. Environmental Protection Agency’s emission limits for wood heaters sold on or after July 1, 1990.
3 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 T able of Contents Specifications ................................................. 4 Installation ...................................................... 5 Clearance Charts ..................
4 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Specifications Defiant, Model 1610 EP A Emissions rating ................................... 0.75 g/hr* Range of heat output ........... 10,000 to 30,300 BTU/hr .* Maximum heat output ......
5 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Installation SAFETY NOTICE: IF YOUR DEFIANT IS NOT PROP- ERL Y INST ALLED, A HOUSE FIRE MA Y RESUL T .
6 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 What Kind of Chimney to Use Y ou must connect the Defiant to a code-approved masonry chimney with a flue liner , to a relined masonry chimn.
7 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 as guides when you drill 1/8” (3mm) holes in the bot- tom of the next section. • Fasten the chimney connector to the chimney . Instructions for various installations follow . Figure 6 illustrates the general layout of chimney connector parts.
8 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Without a thimble, a suitable length of chimney con- nector can be extended through the breech to the inner face of the flue liner , and cemented securely in place. Additional pieces of connector are then attached with sheet metal screws.
9 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 ST245 fireplace flex connector 12/99 Flexible Connector Mantel Shield Fireplace Adapter Kit “Positive Connection” ST245 Fig.
10 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 D E F I A N T ST494 steel wall pass thru 1 1/00 18” (460mm) clear- ance between pipe and sides/top/bottom of opening ST494 Fig.
1 1 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Procedure: 1. Convert specifications to R-value: i. R-value given - no conversion needed. ii. k-factor is given with a required thickness (T) in inches: iii. K-factor is given with a required thickness (T) in inches: iv .
12 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 ST248 wall shield construction 12/14/99 djt Stud W all Framing W all Shield Noncombus- tible Spacers and Fasteners Drywall Air Flow Air Flow Screen Shield Metal Spacer ST248 Fig. 13 Approved wall shield construction.
13 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 An unprotected mantel (“A”, Fig. 15) cannot be more than 9” (230 mm) deep and must have a minimum clearance of 41” (1041 mm), measured from the stove’s top plate. With a ventilated shield, this clearance may be reduced safely to 29” (737 mm).
14 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Defiant NC Clearance Chart for 6” Connections ONL Y Stove Clearance Stove Installed Parallel to W all Unprotected Surfaces Protected Surf.
15 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Defiant NC Clearance Chart for 8” Connections ONL Y Stove Clearance 1 Stove Installed Parallel to W all Unprotected Surfaces Protected Su.
16 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 D E F F C ST486a Defiant Clearance Diagrams 1 1/00 C A B J K L L I I G H P Q R R O M O N U V S T N/A N/A Defiant NC Clearance Diagrams for .
17 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 48" (1220 mm) 48" (1220 mm) 48" (1220 mm) ST498 Defiant Wall shield B 1 1/00 Fig. 17 Parallel installation with rear wall pass-through, two wall shields. Reduced clearances to both rear and side walls.
18 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Distance from the Center of the Flue Collar to the W all for 6” Connections ONL Y The information on this page is helpful in planning stove placement, particularly in those installations with chimneys that pass through the ceiling.
19 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Distance from the Center of the Flue Collar to the W all for 8” Connections ONL Y The information on this page is helpful in planning stove placement, particularly in those installations with chimneys that pass through the ceiling.
20 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Set Up Y our Stove Cast iron stoves are heavy , and it will take two to four people to move your Defiant into position. Wipe the protective coating of oil from the griddle with a clean dry rag or a paper towel.
21 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Install the Optional Ash Door Heat Shield Many installations will require the use of the supplied ash door heat shield. Refer to the “Floor Protection” sections starting on Page 10 to determine if your instal- lation requires the use of the ash door heat shield.
22 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 The Defiant Controls T wo controls regulate the performance of the Defiant: a primary air control supplies oxygen for the fire, and a damper directs air flow within the stove to activate and deactivate the catalytic combustor .
23 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 DEFIANT DEFIANT ST543 Damper positions 1 1/00 Damper Positions Open (Updraft Mode) Closed (Efficient Mode) ST543 Fig. 29 The Defiant’ s damper operating positions.
24 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Infra-Red Reflective Glass Panels for Clear Fire Viewing The outer surfaces of the ceramic glass panels have an infrared-reflective coating which keeps the inner surfaces warm.
25 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Starting and Maintaining a Wood Fire Burn only solid wood in the Defiant, and burn it directly on the grate. Do not elevate the fuel. Do not burn coal or other fuels. The bypass damper must be open when starting a fire or when refueling.
26 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Once the draft is established, open the front door and light the rest of the fuel from the bottom. Do not light the main bed of fuel until the chimney begins drawing, and repeat the procedure as often as necessary if the initial attempt is unsuccessful.
27 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Ash Disposal Routine ash removal is important for ease of main- tenance, and is important for the stove’s durability . Remove ash before it reaches the top of the ash pan. Check the level at least once a day .
28 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 A stove is part of a system, which includes the chimney , the operator , the fuel, and the home. The other parts of the system will affect how well the stove works. When there is a good match between all the parts, the system works well.
29 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 transfer , and it gives you long-term flexibility for install- ing a different stove without relocating the thimble.
30 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Conclusion Wood-burning is an art rather than a science. Once the stove and chimney system are in place, you can only vary your technique, mostly your timing, to achieve good results.
31 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Keep Y our Stove Looking New and Working Its Best Let the fire in the stove go out and allow the stove to cool completely before beginning any maintenance procedure.
32 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Adjust the Damper as Needed The tension on the Defiant’s damper is adjustable to compensate for compression of the gasket that seals the damper to the upper fireback. T o adjust the damper: 1.
33 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 3. Determine the correct length of the appropriate-sized gasket by laying it out in the channel. Allow an extra 1-2” (25-50 mm), and mark the spot to be cut. 4. Remove the gasket from the channel, place it on a wood cutting surface, and cut it at the marked spot with a utility knife.
34 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Clean the chimney connector by disconnecting the sec- tions, taking them outside, and removing any deposits with a stiff wire brush. Reinstall the connector sections after cleaning, being sure to secure the joints between individual sections with sheet metal screws.
35 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 12 87 24 23 20 22 19 21 13 14 5 16 17 18 25 69 64 35 65 6 7 8 39 32 88 42 43 50 41 15 48 38 40 34 2 53 54 55 58 76 75 70 74 68 80 78 67 77 7.
36 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Defiant W oodburning Stove Model 1610 (continued) 1. Side Insulation 30002846 2. Right Side Brick 30002847 3. Left Side Refractory 30002848 4. Brick Support Bracket 30002480 5. Griddle Gasket 1203668 6.
37 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 Defiant W oodburning Stove Model 1610 (continued) Shell Enamel Parts - Defiant Model 1610 Part Name Classic Biscuit Bordeaux Chestnut Ebon.
38 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850.
39 Defiant 1610 Non-Catal ytic W oodbur ning Stove 30002850 L I M I T E D L I F E T I M E W arranty For V ermont Castings Defiant, Non-Catalytic W ood Stove Limited Lifetime W arranty CFM Corporation.
2695 Meadowvale Blvd. • Mississauga, Ontario, Canada L5N 8A3 800-668-5323 • www .cfmcorp.com CFM Corporation.
Een belangrijk punt na aankoop van elk apparaat Vermont Casting 1610 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Vermont Casting 1610 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Vermont Casting 1610 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Vermont Casting 1610 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Vermont Casting 1610 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Vermont Casting 1610 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Vermont Casting 1610 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Vermont Casting 1610 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
