Gebruiksaanwijzing /service van het product FT-1807M van de fabrikant Vertex Standard
Ga naar pagina of 34
Introduction This manual provides technical information necessary for servicing the FT-1807M FM Transceiver. Servicing this equipment requires expertise in handling surface-mount chip components.
2 Specifications General Frequency Range : Tx 400 - 470 MHz Rx 400 - 470 MHz Channel Step : 5/10/12.5/15/20/25/50/100 kHz Standard Repeater Shift : ±600 kHz Frequency Stability : Better than ±5 ppm (–20 °C to +60 °C) Modes of Emission : F2D/F2A/F3E Antenna Impedance : 50 Ohms, unbalanced Supply voltage : 13.
3 Exploded V iew & Miscellaneous Parts g c d e f g g d d d c c c f f f f f f f f e e e e e e e e e e M4090178 SPEAKER Non-designated parts are available only as part of a designated assembly .
4 Note.
5 Block Diagram.
6 Connection Diagram.
7 Circuit Description Receive Signal Path Incoming RF signal is from the antenna jack is deliv- ered to the Main Unit and passed through the low- pass filter network consisting capacitors C1213, C1236.
8 Circuit Description TX APC Circuit A portion of the power amplifier module output is rectified by D1022 ( 1SS321 ), then delivered to APC Q1038 ( LM2904PWR ), as a DC voltage which is pro- portional to the output level of the power amplifier module.
9 Alignment Introduction The FT -1807M is carefully aligned at the factory for the specified performance across the amateur band. Realignment should therefore not be necessary ex- cept in the event of a component failure.
10 Alignment Preparation & Precautions A 50-Ohm RF load and in-line wattmeter must be connected to the antenna jack in all procedures that call for transmission; alignment is not possible with an antenna. After completing one step, read the next step to see if the same test equipment is required.
11 Squelch Threshold Level Inject a 435.100 MHz signal at a level of –14 dBµ (with 1 kHz modulation @±3.5 kHz deviation) from the RF signal generator . Rotate the SQL knob to the 10-o’clock position. Rotate the DIAL knob to set the alignment param- eter to “ 435.
12 CTCSS TX Deviation Rotate the DIAL knob to set the alignment param- eter to “ 435.000 103 435.000 103 435.000 103 435.000 103 435.000 103 .” Press the [ D/MR ( MW )] key to enable adjustment of the “CTCSS TX Deviation.
13 MAIN Unit Circuit Diagram 1.5 V (1.5 V) Ú 1 Ú 2 Q1043 Pin 2 TX ( LOW 1 ) : 0.7 V (2.0 V) TX ( LOW 2 ) : 0.7 V (2.4 V) TX ( LOW 3 ) : 0.7 V (3.1 V) TX ( HIGH ) : 0.7 V (3.8 V) Ú 1 Q1028 Pin RX TX 1 5.0 V 5.0 V 2 --- --- 3 3.0 V 0 V 4 5.0 V 0.6 V 5 5.
14 MAIN Unit Note.
15 MAIN Unit Parts Layout (Side A) B A D CE F 1 2 3 4 5 2SA1774 (FR) (Q1007) 2SC4154 (E) (Q1033) 2SC4400 (RT4) (Q1032) 2SC4617 (BR) (Q1051, 1053) 2SC5226 (R22) (Q1026) 2SC4915O (Q0) (Q1054) 2SC5374 (N.
16 MAIN Unit Parts Layout (Side B) b a d ce f 1 2 3 4 5 2SA1774 (FR) (Q1024, 2027, 1029) 2SC4154 (E) (Q1001, 1021, 1046, 1047) FMMTL718TA (Q1025) 2SJ364 (4M) (Q1034, 1036, 1041, 1042) LM2904PWR (Q1038.
17 PCB with Components CB3539001 FT-180 7 M CB3539002 FT-180 7 E Printed Circuit Board AH023U000 FR014760C 1- C 1001 CHIP TA.CAP. 10uF 10V TAJA106M010Y K78100072 1- B e4 C 1002 CHIP TA.CAP. 10uF 10V TAJA106M010Y K78100072 1- B e4 C 1003 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B e3 C 1005 CHIP CAP.
18 Parts List MAIN Unit REF DESCRIPTION VALUE V/W TOL. MFR'S DESIG VXSTD P/N VERS. LOT SIDE LAY ADR C 1082 AL.ELECTRO.CAP. 100uF 16V RC2-16V101MF1# K40129038 1- A B3 C 1083 CHIP CAP. 0.001uF 50V B GRM188B11H102KA01D K22174809 1- B d4 C 1084 CHIP CAP.
19 Parts List MAIN Unit REF DESCRIPTION VALUE V/W TOL. MFR'S DESIG VXSTD P/N VERS. LOT SIDE LAY ADR C 1166 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A E4 C 1167 CHIP CAP. 100pF 50V CH GRM1882C1H101JA01D K22174235 1- A D3 C 1168 CHIP CAP.
20 Parts List MAIN Unit REF DESCRIPTION VALUE V/W TOL. MFR'S DESIG VXSTD P/N VERS. LOT SIDE LAY ADR C 1251 CHIP CAP. 1pF 50V CK GRM1884C1H1R0BZ01D K22174267 1- A E3 C 1252 CHIP CAP. 1pF 50V CK GRM1884C1H1R0BZ01D K22174267 1- A F4 C 1253 CHIP CAP.
21 Parts List MAIN Unit REF DESCRIPTION VALUE V/W TOL. MFR'S DESIG VXSTD P/N VERS. LOT SIDE LAY ADR L 1003 CHIP COIL 0.0033uH LQN21A3N3D04 L1690606 1- A C5 L 1004 M.RFC 0.022uH 2% C1608CB-22NG L1691036 1- A B4 L 1005 M.RFC 0.015uH TFL0816-15 L1690493 1- B e3 L 1006 M.
22 Parts List MAIN Unit REF DESCRIPTION VALUE V/W TOL. MFR'S DESIG VXSTD P/N VERS. LOT SIDE LAY ADR R 1004 CHIP RES. 100 1/16W 5% RMC1/16S 101JTH J24189013 1- A B5 R 1005 CHIP RES. 22k 1/16W 5% RMC1/16S 223JTH J24189041 1- A B 5 R 1006 CHIP RES. 0 1/16W 5% RMC1/16S JPTH J24189070 1- A C5 R 1007 CHIP RES.
23 Parts List MAIN Unit R 1092 CHIP RES. 2.2k 1/16W 5% RMC1/16S 222JTH J24189029 1- B e3 R 1093 CHIP RES. 1k 1/16W 5% RMC1/16S 102JTH J24189025 1- B e3 R 1094 CHIP RES. 10k 1/16W 5% RMC1/16S 103JTH J24189037 1- A B3 R 1095 CHIP RES. 470 1/16W 5% RMC1/16S 471JTH J24189021 1- A B3 R 1096 CHIP RES.
24 R 1173 CHIP RES. 1k 1/16W 5% RMC1/16S 102JTH J24189025 1- A F3 R 1175 CHIP RES. 47 1/16W 5% RMC1/16S 470JTH J24189009 1- A F4 R 1177 CHIP RES. 10k 1/16W 5% RMC1/16S 103JTH J24189037 1- A F3 R 1178 CHIP RES. 150k 1/16W 5% RMC1/16S 154JTH J24189051 1- A F3 R 1179 CHIP RES.
25 Parts List MAIN Unit REF DESCRIPTION VALUE V/W TOL. MFR'S DESIG VXSTD P/N VERS. LOT SIDE LAY ADR R 1257 CHIP RES. 2.7k 1/16W 5% RMC1/16S 272JTH J24189030 1- B a3 R 1258 CHIP RES. 47k 1/16W 1% RMC1/16 473FTP J24183473 1- A F1 R 1259 CHIP RES. 22 1/16W 5% RMC1/16S 220JTH J24189005 1- A F4 R 1260 CHIP RES.
26 Note MAIN Unit.
27 CNTL Unit Circuit Diagram Ú Ú J2003 Pin RX TX 1 5.0 V 5.0 V 20 V 0 V 30 V 0 V 40 V 0 V 50 V 0 V 60 V 0 V 70 V 0 V 8 1.9 V 1.8 V 9 3.0 V 3.0 V 10 0 V 0 V 11 1.1 V 0 V 12 3.2 V 0 V 13 4.9 V 4.9 V 14 0 V 0 V 15 8.0 V 8.0 V 16 0.6 V 0 V 17 0 V 0 V 18 0 V 0 V 19 --- --- 20 5.
28 CNTL Unit Parts Layout B A D CE F G 1 2 2SC4617 (BR) (Q2007, 2008, 2013) 2SC5374 (NA) (Q2003) BR24L64 (Q2006) HD64F2266TF13 (Q2002) b a d ce f g 1 2 S-812C50AUA (Q2010) BD4830FVE (Q2011) DTC143ZE (.
29 PCB with Components CB3540001 FT-1807M A2 CB3540002 FT-1807M A1 CB3540003 FT-1807M A3 CB3540004 FT-1807E B1 CB3540005 FT-1807E B2 CB3540006 FT-1807M B3 CB3540007 FT-1807E C1 CB3540008 FT-1807E C2 CB3540009 FT-1807M C3 CB3540010 FT-1807E D1 CB3540011 FT-1807E D2 Printed Circuit Board AH023U000 FR014770B 1- C 2001 CHIP CAP.
30 Parts List CNTL Unit REF DESCRIPTION VALUE V/W TOL. MFR'S DESIG VXSTD P/N VERS. LOT SIDE LAY ADR D 2002 LED SML-512WWT86 G2071104 1- A C1 D 2003 LED SML-512WWT86 G2071104 1- A C1 D 2004 LED SM.
31 Parts List CNTL Unit REF DESCRIPTION VALUE V/W TOL. MFR'S DESIG VXSTD P/N LOT … LAY ADR R 2031 CHIP RES. 100 1/16W 5% RMC1/16S 101JTH J24189013 1- A F1 R 2032 CHIP RES. 100 1/16W 5% RMC1/16S 101JTH J24189013 1- A F1 R 2033 CHIP RES. 100 1/16W 5% RMC1/16S 101JTH J24189013 1- A F1 R 2034 CHIP RES.
32 Note CNTL Unit.
.
Copyright 2006 VERTEX STANDARD CO., LTD. All rights reserved No portion of this manual may be reproduced without the permission of VERTEX STANDARD CO., LTD.
Een belangrijk punt na aankoop van elk apparaat Vertex Standard FT-1807M (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Vertex Standard FT-1807M heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Vertex Standard FT-1807M vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Vertex Standard FT-1807M leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Vertex Standard FT-1807M krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Vertex Standard FT-1807M bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Vertex Standard FT-1807M kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Vertex Standard FT-1807M . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
