Gebruiksaanwijzing /service van het product 1100.5 van de fabrikant Viper
Ga naar pagina of 22
model 1100.5.
2 © 2002 Directed Electronics, Inc.
3 © 2002 Directed Electronics, Inc T ABLE OF CONTENTS CONGRA TULA TIONS Congratulations for choosing a Viper Audio power amplifier from Directed Electronics, the industr y leader in high quality automotive security and audio equipment since 1990.
4 © 2002 Directed Electronics, Inc Directed Electronics, Inc. promises to the original purchaser , to replace this product should it prove to be defective in workman- ship or material under normal us.
5 © 2002 Directed Electronics, Inc High-powered car audio systems may produce sound pressure levels that exceed the threshold at which hearing loss may result. They may also impair a driver’ s ability to hear traffic sounds or emergency vehi- cles.
6 © 2002 Directed Electronics, Inc INST ALLA TION GUIDELINES 1. Please read this owner’ s manual carefully before installing this ampli- fier . 2. Disconnect the batter y ground terminal prior to making any elec- trical connections.
7 © 2002 Directed Electronics, Inc electronics and the lower your speaker load, the more heat is generated. For low impedance speaker applications or restricted ventilation installations, an external cooling fan may be advisable.
8 © 2002 Directed Electronics, Inc 1. R R C C A A I I n n p p u u t t J J a a c c k k s s - Accepts line level outputs from head units or signal processors between 150mV and eight volts.
9 © 2002 Directed Electronics, Inc FIGURE 2—AMPLIFIER CONNECTIONS 1100.5 REAR 2 1 5 4 6 1. R R e e m m o o t t e e T T u u r r n n O O n n - This terminal turns on the amplifier when (+) 12 volt is applied to it. Connect it to the remote turn on lead of the head unit or signal source.
10 © 2002 Directed Electronics, Inc TOP P ANEL CONTROLS 1. I I n n p p u u t t G G a a i i n n A A d d j j u u s s t t m m e e n n t t - Controls amplifier sensitivity and is used to match the input level of the ampli- fier to the output level of the signal source.
11 © 2002 Directed Electronics, Inc FIGURE 3—AMPLIFIER CONTROLS TOP 7 1 6 2 5 8 9 3 4.
12 © 2002 Directed Electronics, Inc Control Panel Cover The amplifier’ s gain and filter controls are mounted under the elliptical control panel cover .
13 © 2002 Directed Electronics, Inc SPEAKER WIRING DIAGRAMS Five channel operation (bottom view) Three channel operation (bottom view) N N O O T T E E : : The dual + and -- subout terminals of the 1100.5 are paralleled internally and the combined load impedance should be taken into consideration when connecting multiple subwoofers.
14 © 2002 Directed Electronics, Inc The Viper 1100.5 channel five subwoofer section can be combined with a d600.1 in a master/slave combination for increased power and accurate level matching. They are the Parallel Synced Gain and External Synced Bridged combi- nations.
15 © 2002 Directed Electronics, Inc 1. I I n n p p u u t t / / O O u u t t p p u u t t S S i i g g n n a a l l - Connect these RCA jacks as described in the Front Panel Connections/Controls section of this guide.
16 © 2002 Directed Electronics, Inc FIGURE 5—P ARALLEL SYNC GAINED d600.1/1100.5 1+ 2 3+4 SUB 1-4 OUT SUB OUT SYNC OUT BRIDGE OUT R L REMOTE POWER PROTECTION SUB LEVEL MIN MAX INPUT I/O SLAVE IN SYNC OUT BRIDGE OUT R L SLAVE MA STER REMOTE 1 Do Not Use 4 Do Not Use 2 Do Not Use Master (1100.
17 © 2002 Directed Electronics, Inc 1. I I n n p p u u t t / / O O u u t t p p u u t t S S i i g g n n a a l l - Connect these RCA jacks as described in the Front Panel Connection/Controls section of this guide.
18 © 2002 Directed Electronics, Inc FIGURE 6—EXTERNAL SYNC BRIDGED d600.1/1100.5 1+ 2 3+4 SUB 1-4 OUT SUB OUT SYNC OUT BRIDGE OUT R L REMOTE POWER PROTECTION SUB LEVEL MIN MAX INPUT I/O SLAVE IN SYNC OUT BRIDGE OUT R L SLAVE MA STER REMOTE 1 Do Not Use 4 Do Not Use 2 Do Not Use Master (1100.
19 © 2002 Directed Electronics, Inc Y our Viper Audio power amplifier needs to be adjusted carefully to achieve maximum performance. These are some guidelines to follow when fine-tuning the amplifier . For full-range and simultaneous stereo/mono bass applications, the crossover selection switch should be set to FLA T .
20 © 2002 Directed Electronics, Inc SPECIFICA TIONS RMS continuous power per channel, Channels 1-4 driven into 4 ohms from 20 to 20,000 Hz, with less than 0.08% total Harmonic Distortion @ 14.4 VDC. Channel 5 driven into 4 ohms from 20-250 Hz, with less than 0.
.
22 © 2002 Directed Electronics, Inc The company behind this system is Directed Electronics, Inc. Since its inception, Directed has had one purpose, to provide customers with the finest vehicle security , car stereo products, rear seat entertainment, and accessories available.
Een belangrijk punt na aankoop van elk apparaat Viper 1100.5 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Viper 1100.5 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Viper 1100.5 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Viper 1100.5 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Viper 1100.5 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Viper 1100.5 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Viper 1100.5 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Viper 1100.5 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
