Gebruiksaanwijzing /service van het product C24EO5 van de fabrikant Vulcan-Hart
Ga naar pagina of 24
This Manual is prepared for the use of tr ained Vulcan Service Technicians and should n ot be used by those not properly qualified. This manual is not intended to be all encompassing.
C24EO SERIES STEAMERS TABLE OF CONTENTS G E N E R A L ................................................................................ 3 Installation, Operation and Cleaning ........................................................ 3 Introduction .....
C24EO SERIES STEAMERS - GENERAL GENERAL INSTALLATION, OPERATION AND CLEANING Refer to the Installation & Operation Manual for specific instructions. INTRODUCTION Features ! Requires no water or drain line connections (manual fill & manual drain).
C24EO SERIES STEAMERS - GENERAL TOOLS Standard ! Standard set of hand tools ! Clear silicone sealant ! VOM with an AC current tester (any quality VOM with a sensitivity of at least 20,000 ohms per volt can be used) ! Temperature meter & thermocouple Special ! Thermal Transfer Compound, Dow Corning 340 Part No.
C24EO SERIES STEAMERS - REMOVAL AND REPLACEMENT OF PARTS REMOVAL AND REPLACEMENT OF PARTS COVERS AND PANELS Side Panels 1. Remove screws from bottom of panel. 2. Slide panel down to clear top cover. 3. Reverse procedure to install. Top Cover 1. Remove SIDE PANELS.
C24EO SERIES STEAMERS - REMOVAL AND REPLACEMENT OF PARTS 2. Disconnect lead wires to component being replaced. 3. Remove component. 4. Reverse procedure to install replacement component and check steamer for proper operation. NOTE: If replacing temperature control, see TEMPERATURE CONTROL CALIBRATION in SERVICE PROCEDURES AND ADJUSTMENTS.
C24EO SERIES STEAMERS - REMOVAL AND REPLACEMENT OF PARTS HIGH LIMIT THERMOSTAT Do not sharply bend and kink, or clamp down on the capillary tube or damage may occur. 1. Remove right SIDE PANEL. 2. Disconnect lead wires from high limit. 3. Remove thermostat from mounting bracket.
C24EO SERIES STEAMERS - REMOVAL AND REPLACEMENT OF PARTS C. Install thermostat hand tight. Do not over tighten . TEMPERATURE PROBE 1. Remove right SIDE PANEL and REAR PANEL. 2. Disconnect probe leads from the temperature control. 3. Remove temperature probe from steam vent pipe.
C24EO SERIES STEAMERS - REMOVAL AND REPLACEMENT OF PARTS 5. Partially remove heating element assembly by pulling assembly towards you. 6. Remove high limit thermostat bulb and bracket.
C24EO SERIES STEAMERS - REMOVAL AND REPLACEMENT OF PARTS DOOR Removal 1. Close door. 2. Remove left SIDE PANEL. 3. Remove nuts from upper hinge located inside front panel. 4. Open door slightly, and while holding door, pull upper hinge away from front panel.
C24EO SERIES STEAMERS - REMOVAL AND REPLACEMENT OF PARTS Handle Installation 1. Apply Lubriplate 630AA around slots of outer door housing where step spacers contact housing. 2. Install door handle into outer door housing such that hinge side of door housing is to the left and arrow on handle is pointed upward.
C24EO SERIES STEAMERS - REMOVAL AND REPLACEMENT OF PARTS Assembly 1. Apply Lubriplate 630AA to sides of sliding bracket. 2. Insert spring pin into bottom of sliding bracket. A. Place spring over spring pin. 3. Assemble sliding bracket into stationary bracket.
C24EO SERIES STEAMER - SERVICE PROCEDURES AND ADJUSTMENTS SERVICE PROCEDURES AND ADJUSTMENTS DOOR LATCH ADJUSTMENT Opening a Jammed Door Should the steamer door jam and cannot be opened, DO NOT FORCE OR PRY the door as damage will occur. 1. Lift up on bottom of door at the handle end to disengage latch.
C24EO SERIES STEAMER - SERVICE PROCEDURES AND ADJUSTMENTS HEATING ELEMENT TEST The heating element assembly contains elements molded into a cast aluminum block. 3 pan units have 6 elements and 5 pan units have 3 elements. See wiring diagrams. 1. Turn cooking mode switch to constant.
C24EO SERIES STEAMER - SERVICE PROCEDURES AND ADJUSTMENTS TEMPERATURE CONTROL CALIBRATION To set the temperature control for optimum steamer operation, the elevation above sea level for the service location must first be determined. The steamer was preset at the factory to sea level.
C24EO SERIES STEAMER - ELECTRICAL OPERATION ELECTRICAL OPERATION COMPONENT FUNCTION B u z z e r ................................ Creates audible signal when timed cook cycle is complete and when a low water condition exists. L i m i t i n g C o n t a c t o r ( 1 C O N ) .
C24EO SERIES STEAMER - ELECTRICAL OPERATION COMPONENT LOCATION CONTROL PANEL COMPONENTS FRONT PANEL COMPONENTS F25386 (June 2010) Page 17 of 24.
C24EO SERIES STEAMER - ELECTRICAL OPERATION SEQUENCE OF OPERATION Schematic diagram AI2851 will be used to explain the electrical sequence of operation. Timed Cooking Mode 1. Conditions. A. Steamer connected to correct voltage and is properly grounded.
C24EO SERIES STEAMER - ELECTRICAL OPERATION 8. Turn cook timer off. A. Timer contacts 11 & 14 open, buzzer is de- energized. B. Steamer reverts to hold temperature and continues to cycle until a cook time is dialed on timer, power switch is turned to off, or the door is opened.
C24EO SERIES STEAMER - ELECTRICAL OPERATION SCHEMATIC DIAGRAM F25386 (June 2010) Page 20 of 24.
C24EO SERIES STEAMER - ELECTRICAL OPERATION WIRING DIAGRAMS - HEATING ELEMENTS C24EO3 - 208V/240V F25386 (June 2010) Page 21 of 24.
C24EO SERIES STEAMER - ELECTRICAL OPERATION C24EO5 - 208V/240V F25386 (June 2010) Page 22 of 24.
C24EO SERIES STEAMER - ELECTRICAL OPERATION C24EO5 - 480V F25386 (June 2010) Page 23 of 24.
C24EO SERIES STEAMER - TROUBLESHOOTING TROUBLESHOOTING SYMPTOM POSSIBLE CAUSES Compartment leaks water around door. 1. Steamer not level. 2. Steamer overfilled. Steam leaks around door. 1. Worn gasket. 2. Damaged gasket. 3. Steam vent pipe blocked. 4.
Een belangrijk punt na aankoop van elk apparaat Vulcan-Hart C24EO5 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Vulcan-Hart C24EO5 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Vulcan-Hart C24EO5 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Vulcan-Hart C24EO5 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Vulcan-Hart C24EO5 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Vulcan-Hart C24EO5 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Vulcan-Hart C24EO5 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Vulcan-Hart C24EO5 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
