Gebruiksaanwijzing /service van het product WPL305 van de fabrikant Wasp
Ga naar pagina of 18
WPL305 Thermal Label Printer User’s Guide For Wasp T echnologies DT /TT Printer Copyright W asp Bar Code T echnologies 2004. All rights reserved. No part of this publication may be reproduced or t ransmitted in any form or by any means without the written permission of W asp Bar Code T echnologies.
Contents 1. Introduc tion ......................................................................................... 1 2. Getting S t arted .................................................................................... 1 2.1 Unpacking and Inspection.
1. Introduction Thank you for purchasing the W305 The rmal T ransfer and Direct Thermal Bar Code Printer . Although the printer take s only a small amount of sp ace, it delivers reliable, superior performance. This printer provides both thermal trans fer and direct thermal printing at user selectable speed of: 2.
2.3 Printer Part s Ribbon Access Window T op Cover Open Lever Feed Button Printer T op Cover LED Indicator Figure 1: Top front view 3. Setup 3.1 Setting Up the Printer 1. Place the printer on a flat, secure surface. 2. Make sure the power switch is off.
3.2 Loading the Ribbon The printer automatically detects if a ribbon is inst alled after power on and will switch to thermal transfer or direct t hermal pri nting mode. If printer does not detect the ribbon, the motor that drives the ribbon rewi nd spindle will be turned off.
Figure 3: Ribbon installation 6. Attach the ribbon spindle to the Back Hub by placing the lef t side of the spindle against the knob with the sp ring on it and compressing with the ribbon spindle. Slide the right side down over the other knob. The ribbon spindle should not be able to be removed without re-compressing the spring.
Lower Cover Figure 5: Pull the lever to open the cover 3. Place the roll of labels onto t he center of the paper roll mount. Printer T op Cover Paper Roll Mount Support Bar Paper Guide Te f l o n B a r T op Cover Open Lever Figure 6: Label inst allation 4.
cover . 2. Do not allow the top cover to slam closed. 3. Failure to securely close and lock th e cover will result in poor print quality . 3.7 T op Cover Operation T o Open: 1. When facing the front of the printer pull the cover release levers on both sides of the printer towards you.
when closing the top cover! Figure 8: T op cover is fully open and ready to close Figure 9: Use both hands to close the top cover 5. Do not force the cover! If you are not sure if top cover is locked at a stop position, please do not push top cover to close it or the top cover will be damaged.
4. Power on Utilities There are three power-on utilities to set up and test printer hardware. 1. Printer initialization 2. Ribbon sensor calibration 3. Gap or black mark sensor calibration Note: Y ou must run the #2 and #3 utilities after running the #1 to properly set up the printer .
4.2 Ribbon Sensor Calibration Note: Please make sure the ribbon is properly installed before doing this calibration. Please follow the steps below to calibrate the ribbon sensor . 1. T urn the printer power of f. 2. Press and hold the FEED butt on then turn on the printer .
Print head check pattern Firmware version Firmware checksum Printed mileage (meter) Serial port configuration Country code Print speed (inch/sec) Print darkness Label size (inch) Gap distance (inch) G.
The printer will enter dump m ode after printing the printer configuration. In dump mode, all characters will be printed in 2 columns as in the figure below .
5. Maintenance 5.1 Cleaning Use one or more of the following supplies that meets your needs: Cleaning pens Cleaning swabs Lint-free cloth Printer Part Method Printer Head Let the print head to cool for one minute. Use a cleaning pen to swab the print elements.
The printer is paused. 3. 4. Press the feed button to resume printing. The printer is out of label or ri bbon or the printer settings are not correct Out of label or ribbon Load a roll of labels and follow the instructions in Loading the Labels , then press the feed button to resume printing.
7. Specifications 7.1 Printer Specifications Item W305 Mech ani sm Resolution 203 dpi. Max. Print Width 108 mm. Max. Print Length 1000 mm ( 39” ). Ribbon Capacity 300 meter with 1” core. (Max. OD 67 mm) Printing S peed 2, 3, 4 and 5 ips. Peeler function 2, 3 ips Printing Method Direct thermal and thermal transfer printing.
2D: PDF-417, Maxicode, and DataMatrix. Command Set WPL Environment Operation T emperature: 5 ~ 40. Relative Humidity: 25% ~ 85% (Non Condensing). S torage T emperature: -40 ~ 60. Relative Humidity: 10% ~ 90% (Non Condensing). 7.2 Label Stock Specifications Item Specification T ype Label (Continuous , Die-cut , Fan-fold).
16 8. Product Support If you experience any problems with your W asp printer that you are unable to resolve, use our online support site to register th en call for technical assistance at (214) 547-4100, Monday through Friday , 8:00 AM – 5:00 PM Central Standard T ime.
Een belangrijk punt na aankoop van elk apparaat Wasp Wasp WPL305 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Wasp Wasp WPL305 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Wasp Wasp WPL305 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Wasp Wasp WPL305 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Wasp Wasp WPL305 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Wasp Wasp WPL305 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Wasp Wasp WPL305 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Wasp Wasp WPL305 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
