Gebruiksaanwijzing /service van het product 2000X WESY7773.1 van de fabrikant Weider
Ga naar pagina of 24
CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Model No. WESY7773.1 S erial No. Write the serial number in the s pace above for future reference. QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction.
2 W ARNING DECAL PLACEMENT W ARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. Read all instructions in this manual an d all warnings on the resist ance system b efo re using the resistance system. Use the resist- ance system only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the resistance system are adequately informed of all precautions.
ASSEMBLED DIMENSIONS: Height: 82 in. / 208 cm Width: 64 in. / 163 cm Depth: 80 in. / 203 cm 4 T op Frame High Pulley Lat T ower Backrest Storage Knob Fulcrum Knob Curl Bar Upright Low Pulley Base Plat.
5 Before beginning assembly , carefully read the following information and instructions: • Assembly requires two persons. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
75 6 2. Attach a Wheel (31) to the outside of the Base (1) with an M10 x 108mm Bolt (81), three M10 W ashers (75), and an M10 Nylon Locknut (76). Do not overtighten the Locknut; the Wheel m ust be able to turn easily . Attach the other Wheel (not shown) in the same manner .
7 8. Attach the Leg Lever Bumper (55) to the Front Leg (6) with an M4 x 19mm Screw (77). Lubricate an M10 x 68mm Bolt (56) with grease. Orient the Leg Lever (7) with the slot on the side shown. Attach the Leg Lever to the Front Leg (6) with the Bolt and an M10 Nylon Locknut (76).
8 9. Attach two 8mm Metal Spacers (97), a 60mm Metal Spacer (39), and two Bearing Wheels (46) t o one end of the Seat Carriage (12) with an M8 x 104mm Button Head Bolt (60) and an M8 Nylon L ocknut (65) as shown.
9 14. Attach the two 10-pound Short Caps (20) to the 10-pound Center Resistance Bar (44) with two M4 x 12mm Flat Head Screws (85). Using twelve M4 x 12mm Flat Head Screws (85), attach the two 10-pound.
10 19. Attach a Pulley Housing (94) to the indicated “U”- channel on the 10-pound Center Resistance Bar (44) with an M10 x 102mm Button Head Bolt (24), two Pivot Bushings (74), and an M10 Nylon Locknut (76). Wrap the Long Cable (80) over a 90mm Pulley (28).
1 1 23 80 Rod 28 71 76 11 21. Attach a Pulley Housing (94) to the indicated “U”- channel on the 10-pound Center Resistance Bar (44) with an M10 x 102mm Button Head Bolt (24), two Pivot Bushings (74), and an M10 Nylon Locknut (76). Wrap the Long Cable (80) around a 90mm Pulley (28).
12 27. Slide the four Foam Pads (26) onto the tubes on the Front Leg (6) and the Leg Lever (7). Press four 19mm Round Inner Caps (78) into the ends of the tubes. 28. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENTS, beginning on the following page.
This section explains how to adjust the resistance system. See the EXERCISE GUIDELINES on page 17 for important information about how to get the most benefit from your exercise program. Also, refer to the accompa- n ying exercise guide to see the correct form for each exercise.
14 4 9 80 A TT ACHING THE ACCESSORIES T o attach a Short Handle (49) to a high pulley , first attach the high pulley to the resistance system (see A TT ACHING THE HIGH PULLEYS AND LEG LEVER on page 13). Then, attach the Short Handle to the Short Cable (33) with a Cable Clip (51).
ADJUSTING THE BACKREST T he Backrest (14) can be used in a level position or one of three inclined positions. T o use the Backrest in a level position, secure the Seat Carri age (12) to the adjustment hole in the Bench Rail (5) next to the Front Leg (6) (see ADJUSTING THE SEA T on page 13).
CABLE DIAGRAM The cable diagram shows the proper routing of the Long Cable (80). Use the diagram to make sure that the Cable has been assembled correctly . If the Cable has not been correctly routed, the resistance system will not function properly and damage may occur .
17 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS Muscle Building T o increase the size and strength of your muscles, push them close to their maximum capacity . Y our mus- cles will continually adapt and grow as you progres- sively increase the intensity of your exercise.
Rest for a short period of time after each set. The ideal resting periods are: • Rest for three minutes after each set for a muscle building workout. • Rest for one minute after each set for a toning work- out. • Rest for 30 seconds after each set for a weight loss workout.
19 MONDA Y D ate: / / EXERCISE RESIST ANCE SETS REPS EXERCISE RESIST ANCE SETS REPS EXERCISE RESIST ANCE SETS REPS AEROBIC EXERCISE AEROBIC EXERCISE TUESDA Y Date: / / WEDNESDA Y Date: / / THURSDA Y Date: / / FRIDA Y Date: / / Make photocopies of this page for scheduling and recording your workouts.
M10 Nylon Locknut (76) M8 Nylon Locknut (65) M6 Nylon Locknut (69) M8 Flange Nut (19) M8 W asher (59) M10 Lock W asher (103) 38mm Round Inner Cap (38) 50mm Square Inner Cap (98) 45mm Square Inner Cap .
M10 x 103mm Bolt (66) M10 x 91mm Bolt (90) M10 x 108mm Bolt (81) M6 x 13mm Bolt (92) M4 x 16mm Screw (62) M4 x 19mm Screw (77) M4 x 12mm Flat Head Screw (85) M10 x 25mm Button Head Screw (87) M8 x 19m.
K ey No. Qty . Description Key No. Qty . Description 1 1 Base 2 1 Base Plate 3 1 Upright 4 1 Lat T ower 5 1 Bench Rail 6 1 Front Leg 7 1 Leg Lever 8 1 Backrest Backing 9 1 Seat Backing 10 1 T op Frame.
69 79 100 93 70 65 59 3 8 3 4 1 0 65 59 38 34 21 7 1 2 8 14 8 15 16 21 71 28 54 62 17 17 62 58 58 62 58 53 62 13 9 89 62 62 4 87 87 3 28 76 76 28 28 29 28 29 22 71 73 30 76 66 99 5 41 2 76 82 82 65 60.
Part No. 221079 R1005A Printed in China © 2004 ICON IP , Inc. T o order replacement parts, see the front cover of this manual. T o help us assist you, please be prepared to give the following information: • the MODEL NUMBER of the product (WESY7773.
Een belangrijk punt na aankoop van elk apparaat Weider 2000X WESY7773.1 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Weider 2000X WESY7773.1 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Weider 2000X WESY7773.1 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Weider 2000X WESY7773.1 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Weider 2000X WESY7773.1 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Weider 2000X WESY7773.1 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Weider 2000X WESY7773.1 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Weider 2000X WESY7773.1 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
