Gebruiksaanwijzing /service van het product 831.159833 van de fabrikant Weider
Ga naar pagina of 37
CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference. WEIGHT SYSTEM EXERCISER User ’ s Manual Model No. 831.159833 Serial No. W rite the serial number in the space above for reference.
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 IMPORT ANT PRECAUTIONS W ARNING : T o reduce the risk of serious injury , read the following important precautions before using the weight system. 1. Read all instructions in this manual and in the accompanying literature before using the weight system.
4 ASSEMBLED DIMENSIONS: Height: 77 in. Width: 80 in. Depth: 59 in. Low Pulley Station Foot Plate Leg Lever Press Arm Backrest Curl Pad Butterfly Arm Ab Pulley Station W eight Stack Leg Press Lever Thank you for selecting the innovative and versatile WEIDER ® PRO POWER ST ACK weight system.
5 ASSEMBL Y Make sure that you have the following tools: • T wo adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet •Y ou will also need grease or petroleum jelly , a small amount of soapy water , and masking tape.
1. Before beginning, be sure that you have read and understood the information on page 5. Locate and open the parts bag labeled “FRAME ASSEMBL Y .” Press a 50mm Square Inner Cap (67) into each end of the Butterfly Base (1).
4. Slide the Butterfly Upright (4) over the indicated M8 x 61mm Carriage Bolts (75) in the Butterfly Base (1). Hand tighten two M8 Nylon Locknuts (86) onto the Bolts. Do not tighten the Locknuts yet. 4 7 5. Press three 50mm Square Inner Caps (67) into the Butterfly T op Frame (7).
7 8. Press a 25mm Square Inner Cap (69) into the small tube on the Press Upright (5). Slide the Press Upright (5) over the indicated M8 x 61mm Carriage Bolts (75) in the Press Base (3). Hand tighten two M8 Nylon Locknuts (86) onto the Bolts. Do not tighten the Locknuts yet.
9 10. Press a 50mm Square Inner Cap (67) into the Press T op Frame (9). Attach the Press T op Frame (9) to the indicated bracket at the top of the Press Upright (5) with two M8 x 66mm Bolts (89), a Medium Support Plate (109), and two M8 Nylon Locknuts (86).
10 13. Slide six Weights (41) onto the Right W eight Guides (26). Make sure the Weights are turned so the pin grooves are on the bottom. Press a Weight T ube Bumper (45) into the lower end of the Short Weight T ube (44) . Slide the Short Weight T ube into the center holes in the W eights (41).
11 105 92 29 28 67 8 90 90 90 26 27 4 7 5 8 9 28 5 77 92 35 15 16 38 29 105 90 90 90 15. Press a 50mm Square Inner Cap (67) into the Center T op Frame (8). Place the Center T op Frame on the indicated brackets on the Uprights (4, 5). Note: The tops of the four Weight Guides (26, 27) must be behind the Center T op Frame, as shown in step 16.
12 20. See the inset drawing. Press a Plastic Bushing (60) onto each welded tube on the Press Frame (17). Slide the Press Frame into place on the Press Base (3). Note: This will be a tight fit; the Plastic Bushings should fit onto each end of the welded tubes in the Base.
13 23 86 20 84 73 Bracket 24 4 11 4 90 73 37 34 22. Identify the Right and Left Butterfly Arms (19, 20) by the positions of the welded brackets. Press a 45mm Square Inner Cap (68) into each end of the Right Butterfly Arm (19). Wet the lower end of the Butterfly Arm with soapy water .
14 26. Remove another “V”-pulley (34) from the bag labeled “PULLEY BAG 2.” W rap the Butterfly Cable (73) over the “V”-pulley (34). Attach the “V”-pulley and a Long Cable T rap (37) to the bracket on the back of the Butterfly Upright (4) with an M10 x 58mm Bolt (1 14) and an M10 Nylon Locknut (90).
32. Identify the Ab Cable (74). It is approximately 226 1/2” long, and it has a ball on one end and an eyelet on the other . W rap the Ab Cable (74) over a 90mm Pulley (35) as shown. Place two Pulley Covers (39) over the Pulley , so that the large tabs are on the indicated side.
16 34. Wrap the Ab Cable (74) over a 90mm Pulley (35) in the direction shown. Attach the Pulley to the Double “U”-bracket (31) with an M10 x 45mm Bolt (94) and an M10 Nylon Locknut (90).
17 38 93 32 74 35 38 38. Wrap the Ab Cable (74) over a 90mm Pulley (35) in the direction shown. Attach the Pulley and a Cable T rap (38) to the second set of holes from the bottom in the indicated pair of Pulley Plates (32) with an M10 x 48mm Bolt (93) and an M10 Nylon Locknut (90).
18 41. Locate the Weight Plate (48) that is attached to the bottom of the Bottom Weight (47). See the inset drawing. Attach the end of the Ab Cable (74) to the bottom of the Weight Plate (48) with an M10 x 45mm Bolt (94) and an M10 Nylon Locknut (90).
19 45. Remove the M10 Nylon Locknut (90) used in step 43. W rap the Low Cable (71) under a 90mm Pulley (35). Attach the Pulley and a Cable T rap (38) to the M10 x 121mm Bolt (102) used in step 43 with the M10 Nylon Locknut (90). Make sure the Cable T rap is positioned to hold the Cable in the groove of the Pulley .
20 49. W rap the Press Cable (72) under a 90mm Pulley (35). Attach the Pulley and a Cable T rap (38) to the indicated hole in the Press Upright (5) with an M10 x 93mm Bolt (85), an M10 W asher (97) and an M10 Nylon Locknut (90). Make sure the Cable T rap is positioned to hold the Cable in the groove of the Pulley .
21 53. Wrap the Press Cable (72) around a 90mm Pulley (35) in the direction shown. Attach the Pulley and a Cable T rap (38) to the indicated hole on the right side of the Press Upright (5) with an M10 x 121mm Bolt (102) and an M10 Nylon Locknut (90).
22 57. Remove the M10 Nylon Locknut (90) used in step 53. Route the Press Cable (72) through the Press Frame (17). W rap the Press Cable (72) under a 90mm Pulley (35). Slide a Cable T rap (38) and the Pulley onto the M10 x 121mm Bolt (102) in the bottom of the Press Upright (5).
23 61. Attach the Press Cable (72) to the remaining “U”- bracket (33) with an M8 W asher (100) and an M8 Nylon Locknut (86). Note: Do not completely tighten the Locknut; it should be threaded onto the Cable so that only two threads show past the Locknut (see the inset drawing).
24 65. Press a 45mm Square Inner Cap (68) into the indicated end of the Adjustment T ube (15). Orient the Leg Press Plate (16) and Adjustment T ube (15) as shown in the inset drawing. Attach the Adjustment T ube to the Leg Press Plate (16) with an M8 x 58mm Bolt (1 10), two M8 W ashers (100), and an M8 Nylon Locknut (86).
25 ADJUSTING THE LEG PRESS PLA TE To adjust the position of the Leg Press Plate (16), pull out the Adjustment Pin (40) and slide the Adjustment T ube (15) either backward or forward in the bracket on the Leg Press Lever (14). Line up one of the adjustment holes in the Adjustment T ube with the hole in the bracket and re-insert the Adjustment Pin.
26 81 47 41 41 CHANGING THE WEIGHT SETTING To change the setting of a weight stack, insert a W eight Pin (81) under the desired W eight (41). Insert the Weight Pin so that the bent end touches the weight stack.
27 WEIGHT RESIST ANCE CHART The chart below shows the approximate weight resistance at each exercise station. “Left T op” and “Right T op” refer to the 6 lb. top weights. “Bottom” refers to the 12.5 lb. bottom weight. The other numbers refer to the 12.
28 The threaded ends on the Rear Cable (70) and the Press Cable (72) attached to the weight stacks can be used to tighten the cables. To tighten the Rear Cable (70), remove the M8 x 45mm Bolt (96) and the M8 Nylon Locknut (86) from the “U”-bracket (33) and the Short Weight T ube (44).
29 97 12 72 92 34 90 97 5 72 85 34 5 90 37 37 Slack can be removed from the Press Cable (72) by moving the “V”-pulley (34) attached to the Press Seat Frame (12) closer to the Press Upright (5).
CABLE DIAGRAMS The Cable Diagrams below and on the next page show the proper routing of the Rear Cable (70), the Low Cable (71), the Press Cable (72), the Butterfly Cable (73), and the Ab Cable (74).
Low Cable (71) 5 4 3 1 2 6 7 3 1 8 9 10 11 5 6 2 1 4 1 2 4 3 2 3 Butterfly Cable (73) 5 Rear Cable (70) 31 4 Ab Cable (74).
M10 x 63mm Carriage Bolt (76) M6 x 65mm Bolt (79) M4 x 25mm Screw (80) M10 x 67mm Bolt (82) M10 Nylon Locknut (90) M8 Nylon Locknut (86) M6 Nylon Locknut (103) M8 x 66mm Bolt (89) M10 x 69mm Bolt (92).
M10 x 97mm Bolt (77) M10 x 93mm Bolt (85) M10 x 76mm Bolt (88) M6 x 62mm Carriage Bolt (91) M10 x 91mm Bolt (101) M10 x 121mm Bolt (102) M10 x 72mm Bolt (105) M10 x 207mm Bolt (106) M10 x 92mm Carriag.
25mm Retainer (54) 25mm Round Cover Cap (55) 25mm Round Inner Cap (66) 19mm Round Inner Cap (64) 50mm Square Inner Cap (67) 45mm Square Inner Cap (68) 25mm Square Inner Cap (69).
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 11 Butterfly Base 21 Center Base 31 Press Base 41 Butterfly Upright 51 Press Upright 61 Upright Sup.
62 59 62 62 5 6 35 38 38 35 35 38 35 35 38 37 34 18 18 60 35 38 38 32 32 23 12 34 37 38 38 38 38 14 40 35 35 61 61 109 50 15 16 47 41 41 27 46 26 46 42 44 45 33 35 17 9 35 29 38 35 109 32 32 38 35 35 .
Part No. 202725 R1203A Printed in China © 2003 Sears, Roebuck and Co. FULL 90-DA Y W ARRANTY For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this .
Een belangrijk punt na aankoop van elk apparaat Weider 831.159833 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Weider 831.159833 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Weider 831.159833 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Weider 831.159833 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Weider 831.159833 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Weider 831.159833 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Weider 831.159833 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Weider 831.159833 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
