Gebruiksaanwijzing /service van het product 9940 van de fabrikant Weider
Ga naar pagina of 33
® USER’S MANUAL Model No. WESY97310 Serial No. The serial number is found in the location shown below . Write the serial number in the space above. Serial Number Decal Patent Pending Visit our website at www .
2 Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Before Y ou Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 ASSEMBLED DIMENSIONS: Height: 77 in. Width: 80 in. Depth: 55 in. Low Pulley Station Foot Plate Leg Lever Press Arms Backrest Curl Pad Butterfly Arms Ab Pulley Station Weight Stacks Leg Press Lever Thank you for selecting the innovative and versatile WEIDER ® PRO 9940 home gym.
4 Note: This introduction will save you more time than it takes to read it! Identifying Parts T o help you identify the small parts used in assem- bly , we have included a P ART IDENTIFICA TION CHART located in the center of this manual.
1. Before beginning, make sure that you have read and understood the information on page 4. Locate and open the parts bag labeled “FRAME ASSEMBL Y .” See drawing 1a. Press a 2” Square Inner Cap (28) into each end of the Butterfly Base (4). Press two 2” Square Inner Caps (28) into the Weight Base (5).
3. Place the bracket on the lower end of the Butterfly Upright (1) over the indicated 5/16” x 2 1/2” Carriage Bolts (92) in the Butterfly Base (4). Hand tighten two 5/16” Nylon Locknuts (64) onto the Bolts. Do not tighten the Nylon Locknuts yet.
7. Press a 1” Square Inner Cap (98) into the small tube on the Press Upright (2). Place the bracket on the lower end of the Press Upright (2) over the indicated 5/16” x 2 1/2” Carriage Bolts (92) in the Press Base (6). Hand tighten two 5/16” Nylon Locknuts (64) onto the Bolts.
8 10. Lubricate the 3/8” x 3” Bolt (88). Attach the Leg Press Lever (83) to the Press Base (6) with the Bolt and a 3/8” Nylon Locknut (50). Do not overtighten the Nylon Locknut; the Leg Press Lever must pivot easily . 10 1 1. Place two Weight Bumpers (51) over the indicated holes in the Weight Base (5).
9 14. Attach the Weight T op Frame (66) to the Press T op Frame (9) with one 3/8” x 2 3/4” Bolt (46), a Support Plate with 4” center holes (94), and a 3/8” Nylon Locknut (50). Slide a 3 1/2” Pulley (24) with a Cable T rap (25) onto a 3/8” x 4” Bolt (78).
15 15. Attach each of the four Weight Guides (15) to the Weight T op Frame (66) with a 3/8” x 3 3/4” Bolt (59), a 3/8” Flat W asher (48), and a 3/8” Nylon Locknut (50). Important: Go back and fully tighten all Nylon Locknuts used in steps 1 through 15.
11 20. Locate and open the parts bag labeled “PULLEY BAG 2.” Remove one “V”-Pulley (27) from the bag. Leave the remaining pulleys in the bag for identification of the Pro Pulley . Wrap the Butterfly Cable (73) around a “V”-Pulley (27) in the direction shown.
12 23. Attach the Butterfly Cable (73) to the bracket on the Right Butterfly Arm (1 1) with a 3/8” x 1” Bolt (84) and two 3/8” Nylon Jamnuts (63). Note: The loop on the Cable and the two Nylon Jamnuts must be mount- ed underneath the welded bracket.
13 26. Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in the direction shown. Attach the Pulley to the Small Pulley Bracket (22) with a 3/8” x 1 3/4” Bolt (57) and a 3/8” Nylon Locknut (50). Make sure the Pulley Bracket is oriented as shown.
14 29. Wrap the Ab Cable (74) around a 4 1/2” Pulley (82) in the direction shown. Attach the Pulley inside the indi- cated bracket on the Weight T op Frame (66) with a 3/8” x 1 3/4” Bolt (57) and a 3/8” Nylon Locknut (50). Make sure the threaded end of the Ab Cable is routed through the bracket, as shown.
15 31. Remove a Pro Pulley (26) from the bag labeled “PULLEY BAG 2. Identify the Low Pulley Cable (75). It is approximately 143 1/2” long and it has a ball on one end and a loop on the other . Route the end with the loop through the slot in the cable guide on the Butterfly Base (4).
16 35 75 46 48 48 63 35. Attach the loop on the end of the Low Pulley Cable (75) to the indicated hole in the Small Leg Lever (41) with a 3/8” x 2 3/4” Bolt (46), two 3/8” Flat W ashers (48), and a 3/8” Nylon Jamnut (63). 36. Remove a Pro Pulley (26) from the bag labeled “PULLEY BAG 2.
17 39. Important: Although the following steps are not difficult to perform, the correct routing of the cable is critical to the functioning of the home gym.
18 43. Wrap the Press Cable (72) around a 3 1/2” Pulley (24) in the direction shown. Attach the Pulley and a Cable T rap (25) to the indicated hole on the far side of the Leg Press Lever (83) with a 3/8” x 4 3/4” Bolt (60) and a 3/8” Nylon Jamnut (63).
19 47. Route the threaded end of the Press Cable (72) around the 3 1/2” Pulley (24) that was mounted on the bracket on the Weight Base (5) in an earlier step. 47 24 5 72 48. Wrap the Press Cable (72) over a 4 1/2” Pulley (82) in the direction shown.
20 Seat Assembly 50. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Attach the Backrest (12) to the indicated holes in the Butterfly Upright (1) with two 1/4” x 2 1/2” Bolts (79) and two 1/4” Flat W ashers (71). 50 79 79 1 12 71 51.
21 Miscellaneous Assembly 52. Insert a 1/4” x 2 1/2” Carriage Bolt (45) through the center hole in a Seat Plate (65). Attach the Seat Plate to a Seat (13) with two 1/4” x 3/4” Bolts (49).
22 56 56. Apply the WEIDER PRO 9940 decal in the location shown. Important: The warning decals shown below have been attached to the home gym in the locations shown. If a decal is missing or illegible, please call our customer hotline at the number on the front cover of this manual to order a replacement decal.
23 Cable Diagrams The cable diagrams below and on the next page show the proper routing of the Butterfly Cable (73), the Ab Cable (74), the Low Pulley Cable (75) and the Press Cable (72).
24 14 2 1 5 15 13 6 9 3 7 11 4 8 10 12 Press Cable (72).
25 ADJUSTING THE LEG PRESS PLA TE T o adjust the position of the Leg Press Plate (55), pull out the Lock Pin (91) and slide the Adjustment T ube (90) backwards or forwards in the bracket on the Leg Press Lever (83). Line up one of the adjustment holes in the Adjustment T ube with the hole in the bracket and re-insert the Lock Pin.
26 Slack can be removed form the Press Cable (72) by moving one or both of the “V”-Pulleys (27) on the Press Cable. One “V”-Pulley (27) is attached to the small tube on the Press Upright (2). There are three free holes in the small tube, and you can move the “V”-Pulley to any one of them to tighten the cables.
27 The threaded ends on the Press Cable (72) and the Ab Cable (74) that are attached to the weight stacks can also be used to tighten the cables. T o tighten the Ab Cable (74), remove the “U”-Bracket (97) from the Short Weight Tube (17) by removing the 5/16” x 1 3/4” Bolt (96) and the 5/16” Nylon Locknut (64).
3/8" Nylon Locknut (50) 3/8" Nylon Jamnut (63) 5/16" Nylon Locknut (64) 1” T ap Screw (80) 3/8" x 2" Bolt (54) 1/4" Flat W asher (71) 5/16" x 1 3/4" Bolt (96).
3/8" x 3 1/2" Bolt (56) 3/8" x 4 3/4" Bolt (60) 3/8" x 2 3/4" Bolt (46) 3/8" x 3" Bolt (88) 3/8" x 3 1/2" Carriage Bolt (95) 3/8" x 3 3/4" B.
3/4" Round Inner Cap (43) 1” Retainer Ring (31) 1" Round Outer Cap (38) 1" Square Inner Cap (98) 1 3/4" Square Inner Cap (35) 1" Round Inner Cap (76) 1" Round Inner Cap.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Part List—Model No. WESY97310 R0601A Key No. Qty .
46 57 57 59 59 24 50 24 46 78 56 60 59 87 62 52 50 87 64 64 25 63 24 89 92 92 95 64 64 30 30 43 51 89 80 25 24 54 62 63 50 24 25 50 88 24 60 63 25 24 92 92 101 102 89 87 64 71 79 68 50 24 57 22 57 50 .
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.
Een belangrijk punt na aankoop van elk apparaat Weider 9940 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Weider 9940 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Weider 9940 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Weider 9940 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Weider 9940 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Weider 9940 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Weider 9940 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Weider 9940 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
