Gebruiksaanwijzing /service van het product WESY19001 van de fabrikant Weider
Ga naar pagina of 24
USER'S MANUAL QUESTIONS? As a manufacturer , we are committed to providing complete customer satisfaction. If you have questions, or if there are missing parts, we will guarantee complete satisfaction through direct assistance from our factory . TO A VOID UNNECESSAR Y DELA YS, PLEASE CALL DIRECT TO OUR T OLL-FREE CUSTOMER HOT LINE.
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. Read all instructions in this manual and in the accompanying literature before using the training system. 2. It is the responsibility of the owner to ensure that all users of the training system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arm Curl Pad Curl Frame Press Arm Weight Stack Backrest Shroud Seat Thank you for selecting the versatile WEIDER ® 245 training system. The WEIDER ® 245 of fers a selection of weight stations designed to develop every major muscle group of the body .
1/4" Nylon Lockn ut (2) 1/2" x 1/2" Spacer (61) 1/4" Flat W asher (78) 5/16" Flat W asher (70) 5/8" x 1/2" Spacer (82) 3/8" Nylon Jamnut (67) Cable Clip (53) 1&.
1/4" x 2 1/4" Carriage Bolt (38) 5/16" x 6" Bolt (60) 3/8" x 5" Bolt (75) 3/8" x 4 1/4" Bolt (64) 3/8" x 4" Bolt (16) 3/8" x 3 1/4" Bolt (8).
7 ASSEMBL Y Make sure you have the following tools: • T wo (2) adjustable wrenches • One (1) standard screwdriver • One (1) phillips screwdriver • One (1) rubber mallet • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape.
3 4 FRAME ASSEMBL Y 8 1 21 42 4 19 25 Pin Groove 62 3. Attach the Front Upright (42) to the Base (4) using two 3/8” x 2 1/4” Bolts (1) and two 3/8” Nylon Locknuts (21). Do not tighten the Nylon Locknuts yet. 4. Slide a Weight Bumper (19) down over each Weight Guide (62).
5. Insert the Weight Tube Cap (72) into the indi- cated end of the Weight Tube (63). Slide the Weight Tube into the center holes in the Weights (25). Slide the T op Weight (56) down onto the Weight Guides (62) as shown. 6. Press four 1 1/2” x 2 1/2” Inner Caps (27) into the T op Frame (55).
ARM ASSEMBL Y FRAME ASSEMBL Y 8. Attach the T op Frame (55) to the Weight Guides (62) using a 5/16” x 6” Bolt (60), two 1/2” x 1/2” Spacers (61), and a 5/16” Nylon Locknut (3) as shown. Tighten all Nylon Locknuts used in steps 3 through 8. 9.
11 ARM ASSEMBL Y 1 1. Attach the Seat Plate (37) to the Seat Frame (36) using a 1/4” x 2 1/4” Carriage Bolt (38), a 1/4” Flat W asher (78), and a 1/4” Nylon Locknut (2). 12. Attach a Bumper (1 1) to the Seat Frame (36) using a #10 x 1” Screw (80).
18 15 48 47 Bracket Lubricate 55 65 68 45 44 47 16 17 CABLE ASSEMBL Y ARM ASSEMBL Y 12 15. Press a 1 3/4” Square Inner Cap (44) into the lower end of the Left Arm (47). Using a small amount of soapy water , slide a Foam Arm Pad (45) onto the Left Arm.
19. Route the Short Cable (23) around two “V”- Pulleys (6). Attach the “V”-Pulleys and two Long Cable T raps (50) to the Left Arm (47) and the Right Arm (48) as shown, using two 3/8” x 2 1/2” Bolts (7) and two 3/8” Nylon Locknuts (21). Do not overtighten the Nylon Locknuts.
26 23 24 25 23. Important: As you assemble the Long Cable (69) in steps 23–30, refer to the Cable Diagram on page 21. Route the Long Cable (69) between the Base (4) and the Press Frame (17) as shown.
27. Route the Long Cable (69) behind the Press Frame (17) and under the Seat Frame (36) as shown. Route the Long Cable (69) around two 3 1/2” Pulleys (15). Slide the 3/8” x 5” Bolt (75) through the 3 1/2” Pulleys (15), two Cable T raps (66), and the Press Frame (17) as shown.
31. Attach the Seat (13) to the Seat Frame (36) using two 1/4” x 3/4” Bolts (18), a 1/4” x 2 1/4” Bolt (33), and a 1/4” Flat W asher (78). 32. Attach the Backrest (41) to the Front Upright (42) using two 1/4” x 3” Bolts (43) and two 1/4” Flat W ashers (78).
35. Attach the Shroud (59) to the brackets on the T op Frame (55) and the Base (4) using four #8 x 1/2” Screws (79). 17 35 79 79 59 55 79 4 SEA T ASSEMBL Y 36. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENT , beginning on page 18 of this manual.
18 54 39 53 52 23 25 26 CHANGING THE WEIGHT SETTING T o change the weight setting of the weight stack, insert the Weight Pin (26) under the desired W eight (25). Be sure to insert the Weight Pin until the bent end of the Weight Pin is touching the W eights, and turn the bent end downward.
19 This chart shows the approximate weight resistance at each exercise station. “T op” refers to the 6.5 lb. top weight. The other numbers refer to the 10 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm.
20 TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the training system. Replace any worn parts immediately . The training system can be cleaned using a damp cloth and mild non-abrasive detergent.
21 CABLE DIAGRAM The diagram below shows the proper routing of the Short Cable (23) and the Long Cable (69). Use the diagram to be sure that the cables and the cable traps have been assembled correctly . If the cables have not been cor- rectly routed, the training system will not function properly and damage may occur .
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. P ART LIST—Model No. WESY19001 R0201A Key No. Qty .
2 21 66 15 64 9 21 21 8 43 21 68 65 48 42 45 44 79 79 79 79 3 61 62 60 23 86 57 56 63 26 25 73 14 73 5 21 58 15 15 12 58 1 4 3 3 21 21 21 19 19 77 12 27 53 21 21 15 17 16 52 39 22 3 15 75 46 46 31 49 .
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.
Een belangrijk punt na aankoop van elk apparaat Weider WESY19001 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Weider WESY19001 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Weider WESY19001 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Weider WESY19001 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Weider WESY19001 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Weider WESY19001 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Weider WESY19001 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Weider WESY19001 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
