Gebruiksaanwijzing /service van het product 1F91W-71 van de fabrikant White Rodgers
Ga naar pagina of 36
OPERA TION GUIDE Multi-stage Electronic Digital Thermostat 1F91W -71 WHITE-RODGERS Operator: Save this booklet for future use!.
2 Please read this manual thoroughly before operating or programming your thermostat. If you have questions, you may write to our Technical Service Department at the address shown on the back cover of this booklet.
3 In This Guide . . . YOUR NEW THERMOSTAT'S FEATURES ........................................... 4 OPERATING YOUR THERMOSTAT ........ 5 PARTS OF THE THERMOSTAT The Back Of the Thermostat Body The Display The Thermostat Buttons OPERATING FEATURES PROGRAMMING YOUR THERMOSTAT .
4 • Computed Energy Management Recovery (EMR) • Automatic changeover (operator selectable) • Five-day/two-day programming capability • Simultaneous heat and cool program stor- age • Preprogr.
5 Before you begin programming your new ther- mostat, you should be familiar with its features and with the display and the location and opera- tion of the thermostat buttons. The information in this section will help you become familiar with your thermostat so that you can easily program it.
6 PARTS OF THE THERMOSTAT The Back of the Thermostat Body Turn the thermostat body over. On the back are the 9 volt Energizer ® alkaline battery and the option switches.
7 line battery. The battery will provide power for all functions except the display light and audio prompting, which work only on 24 VAC power. If the word BAT is displayed con- tinuously (non-flashing), the thermostat is not being supplied with 24 VAC power and is being powered by the battery alone.
8 Other than and , the buttons are located behind the thermostat door. To open the door, use your fingernail in the indentation at the top center of the door. Pull the door out, then swing the door down on its hinges. Following are brief descriptions of the display and the thermostat buttons.
9 1 2 3 4 6 6 2 DAY 5 DAY 2 3 5 4 FAN FAN BAT 5 DAY FAN VIEW PRGM ADV PRGM FAN ON - AUTO HOLD TEMP RUN PRGM SET CLOCK SET DAY SYSTEM HEAT - OFF - COOL - AUTO TIME FWD TIME BACK.
10 The Thermostat Buttons Sets the system mode ( HEAT ing, OFF , COOL ing, or AUTO matic changeover [user selectable feature]). Selects fan operation (see #6, above). This button is also used to program the fan to run continuously during a program period.
11 10 11 12 13 14 15 16 17 18 9 7 8 5 DAY FAN VIEW PRGM ADV PRGM FAN ON - AUTO HOLD TEMP RUN PRGM SET CLOCK SET DAY SYSTEM HEAT - OFF - COOL - AUTO TIME FWD TIME BACK.
12 OPERATING FEATURES Now that you are familiar with the thermostat display and buttons, read the following informa- tion to learn about the many features of the thermostat.
13 power. If the switch is OFF (down), use a pencil or small screwdriver to move the switch to the ON position (see figure at right). Leave the battery out of the thermo- stat for at least two minutes , to allow the thermostat to reset itself. DO NOT MOVE ANY OTHER OPTION SWITCH , as it may affect thermostat operation.
14 • TWO HOUR TEMPERATURE OVER- RIDE — Press or until the display shows the temperature you want. The thermostat will override current pro- gramming and keep the room temperature at the selected temperature for two hours. After two hours, the thermostat will auto- matically revert to the program.
15 A cooling anticipation setting of less than 10 may cause decreased compres- sor life. To adjust anticipation, press SET CLOCK and SET DAY at the same time. The display will show HEAT 8 (this is the factory preprogrammed heating anticipation setting).
16 • BACKLIT DISPLAY — When you press any button on the thermostat, the display is lit for approximately eight seconds (this fea- ture works only when the thermostat is attached to the wall and 24 VAC power is present to the thermostat).
17 PLANNING FOR YOUR NEEDS This thermostat will store separate heating and cooling programs for five-day (weekday) and two-day (weekend) operation. Usually, the five- day program is set to run Monday through Fri- day, and the two-day program is set to run Saturday and Sunday.
18 questions 1 through 4. If you are using the thermostat in your home, answer questions 5 through 8. Keep in mind that you should plan for both weekday and weekend programs. FOR COMMERCIAL APPLICATIONS: 1a. What time does the first person arrive at the building in the morning? b.
19 6a. What time does the last person leave the house in the morning? b. What temperature should the house be at this time? These will be your DAY tempera- ture settings. 7a. What time does the first person arrive home in the evening? b. What temperature should the house be at this time? These will be your EVE (evening) temperature settings.
20 Heating Program for ALL days of the Week: Cooling Program for ALL Days of the Week: PERIOD TIME TEMP PERIOD TIME TEMP MOR DAY EVE NHT 5:00 AM 9:00 AM 4:00 PM 10:00 PM 70 70 70 64 MOR DAY EVE NHT 5:.
21 WEEKDAY (5 DAY) WEEKEND (2 DAY) Start Time Temperature Start Time Temperature MOR HEAT DAY HEAT EVE HEAT NHT HEAT MOR COOL DAY COOL EVE COOL NHT COOL Heating/Cooling Schedule Plan.
22 WEEKDAY (5 DAY) WEEKEND (2 DAY) Start Time Temperature Start Time Temperature MOR HEAT DAY HEAT EVE HEAT NHT HEAT MOR COOL DAY COOL EVE COOL NHT COOL SAMPLE Heating/Cooling Schedule Plan 5:30 AM 8:.
23 ENTERING YOUR PROGRAM Follow these steps to enter the heating and cooling programs you have selected. We recommend that you remove the thermostat from the wall for programming (especially for entering cooling programming). A fresh 9 volt Energizer ® alkaline battery must be installed to perform off-wall programming.
24 5. Press SET DAY once. The display will show the day of the week as an abbreviation ( MO for Monday, TU for Tuesday, etc.). 6. Press and hold either TIME FWD or TIME BACK until you reach the current day of the week. 7. Press RUN PRGM once. The display will show the correct time and room temperature alter- nately.
25 AM, and 70 ° is the programmed tempera- ture (this example reflects factory prepro- gramming). 3. To change the displayed start time to your selected start time for weekday MOR heat program, press TIME FWD or TIME BACK until your selected time appears.
26 Enter Cooling Program If outside temperature is below 50 ° F, we recommend that you remove the ther- mostat from the wall before proceeding with the following steps to program cool- ing temperatures. Personal injury or property damage may occur due to air conditioner compressor slugging.
27 3. Press RUN PRGM . 4. Press SYSTEM HEAT - OFF - COOL - AUTO until COOL is displayed. 5. Repeat step 2 to check cooling tempera- tures. 6. Press RUN PRGM to begin program operation.
28 1. How can I permanently change a part of my program? Press VIEW PRGM until you reach the time/tem- perature schedule you want. Then press or and TIME FWD and TIME BACK to change the program.
29 4. What happens if the electricity goes off or is manually shut off? If you have not installed a 9 volt alkaline battery, the display will go blank and the program will be lost in approximately one minute.
30 To correct this, remove the thermostat from the wall and disconnect the battery. Wait about one minute, then reconnect the bat- tery. The thermostat will revert to the factory preset program until you reprogram the thermostat.
31 The display light and audio prompting (beep) only work when the thermostat is on the wall and 24 VAC power is present to the thermo- stat. These features will not work on battery power alone. See OPERATING YOUR THERMOSTAT . 9. The display is flashing BAT.
32 • The EMR function is operating. The EMR function will bring the system on auto- matically to bring the temperature to the selected level by the beginning of the next program period. See OPERATING YOUR THERMOSTAT . • You have programmed the incorrect day or time.
33 14. Between heating and cooling seasons, I want to turn my system off. Can I do this without affecting my thermostat program- ming? Any time you wish to turn your system off, simply press SYSTEM HEAT - OFF - COOL - AUTO until the display shows OFF .
34 dead. If you are changing the battery after seeing a flashing BAT on the display, the installed battery may be dead. If you remove the old battery and install a fresh one within one minute, you should not lose your ther- mostat programming.
35.
If you need further information on programming or operation, you may write to our Technical Service Department at the address shown below. WHITE-RODGERS DIVISION EMERSON ELECTRIC CO.
Een belangrijk punt na aankoop van elk apparaat White Rodgers 1F91W-71 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen White Rodgers 1F91W-71 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens White Rodgers 1F91W-71 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding White Rodgers 1F91W-71 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over White Rodgers 1F91W-71 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van White Rodgers 1F91W-71 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de White Rodgers 1F91W-71 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met White Rodgers 1F91W-71 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
