Gebruiksaanwijzing /service van het product 4210 van de fabrikant Wilton
Ga naar pagina of 24
Operating Instructions — Parts Manual Wilton Belt and Disc Sanding Machine Model: 4210 WHM TOOL G ROUP 2420 V antage Drive Elgin, Illinois 60123 Part No.
This manual has been prepared for owners of Wilton Model 4210 Belt and Disc Sanding Machine. Its purpose is to promote safety through the use of accepted operating and maintenance procedures.
3 T able of Content s Cover Page ..................................................................................................................... ...... 1 General Specifications ....................................................................
4 General Specifications Belt Size 6" x 48" Disc Size 10 " Motor Horsepower 1 H P V o lt ag e 1 15/230 V ac (pre-wired for 1 15 V ac) Switch Removable Safety Key Platen Cast Iron T ables Cast Iron (2) Belt Speed 1650 SFPM Disc Speed 2100 RPM Dust Collection Shrouds T wo (standard) Weight 120 lbs.
5 - Never operate with machine guards missing. - Always wear safety glasses with side shields (See ANSI Z87.1) - Never wear loose clothing or jewelry . - Never overreach — you may slip and fall into the machine. - Never leave machine running while you are away from it.
6 General Electrical Cautions This machine should be grounded in accordance with the National Electrical Code and local codes and ordinances. This work should be done by a qualified electrician. The machine should be grounded to protect the user from electrical shock.
7 Introduction This manual includes operating and maintenance instructions for the Wilton Model 4210 Belt and Disc Sander . This manual also includes p arts listings and illustrations of replaceable parts. Belt and Disc Sander Features Figures 1 and 2 depict the main features of the Wilton Model 4210 Belt and Disc Sander .
8 The disc sander consists of an aluminum disc onto which is installed an adhesive-backed sanding and other abrasive discs. The disc is contained within a ducted shroud. The sanding disc can be replaced by removing the table and a cover over the lower portion of the disc.
9 Operation This section defines the controls and other features with which the operator should be familiar . Refer to Figures 3 and 4 for some typical sander operations. Figure 3. Contouring with Belt Sander Figure 4. Sanding using Disc Sander Controls The ON/OFF switch is located on the side of the machine base (refer to Figure 5).
10 Adjusting Platen Housing Position The sanding belt can be operated with the platen housing horizontal, vertical, or at any angle in between. Change position of the platen housing as follows: W ARNING : DISCONNECT ELECTRICAL POWER TO THE MACHINE BEFORE PERFORMING ANY MAINTENANCE.
11 Maintenance This section provides procedures required to main- tain the belt/disc sander . The numbers in parenthe- ses throughout the manual correspond with reference numbers for parts shown in the exploded views in the Replacement Parts section. Lubrication The bearings used in the sanding machine are sealed, pre-lubricated bearing.
12 9. Install plate (55) and secure with four screws (56). Check for clearance between plate (55) and the sanding disc. 10. Install table (60) onto rod (74). Position table so it is level and tighten screw (65) against rod (74). 1 1. Connect electrical power and operate machine to check operation.
13 Replacement of Motor W ARNING : DISCONNECT ELECTRICAL POWER TO THE MACHINE BEFORE PERFORMING ANY MAINTENANCE. 1. Disconnect electrical power . 2. Remove four screws from base. With assistance of the second person, lift base from stand. NOTE : Place base on bench.
14 Wiring Data Figure 10: Pictoral diagram for single phase motor , 1 15 volts w/plug. Single phase electrical hook-up When connecting your machine to single phase power you may be connecting to either 1 15 or 230 volts, depending upon the motor type provided.
15 Connecting Power for 3-phase Motors 1. Be certain the power to the branch you are connecting is off, and locked out, so power cannot be reestablished, accident ally . 2. Connect the ground wires. Thse wires will be either green, or green with a white trace.
16 T roubleshooting Fault Probable Cause Remedy Machine does not start. 1. Blown fuse or tripped 1. Determine reason for blown fuse/tripped circuit breaker . breaker (such as a short circuit or motor overload). Correct reason for fault. Replace fuse/reset breaker .
17 Replacement Parts This section provides exploded view illustrations that show the replacement parts for the Wilton Model 4210 Belt/ Disc Sander . Also provided are parts listings that provide part number and description. The item numbers shown on the illustration relate the item number in the facing parts listing.
18 Ref. Part No. Number Description Q ty . 1 5513476 Panel, Access 1 2 5513477 Knob 2 3 5515307 Stand, Complete 1 Assembled V iew and Parts Listing of S tand – Model 4210 Belt and Disc Sander 3 2 1.
19 Exploded V iew – W ilton Model 4210 Belt & Disc Sander.
20 Parts Listing – Wilton Model 4210 Belt & Disc Sander Ref. Part No. Number Description Q t y 2 551301 1 Base 1 3 5513012 Bracket 1 4 5513013 Platen 1 5 5513014 Drum, Drive 1 6 5513015 Shaft, D.
21 Wiring Diagram WHITE BLACK BLAC K WHIT E GREE N GREE N GROUND 300MFD 125 VAC 4210 ELECTRICAL S C HEMATIC - 1 1 5V GREY BLACK YELLOW RED WHITE BLACK GREEN GREE N 4210 ELECTRICAL S C HEMATIC - 2 3 0V.
Notes.
Notes.
WHM TOOL GROUP 2420 V antage Drive Elgin, Illinois 60123 Ph.: 800-274-6848 www .wmhtoolgroup.com.
Een belangrijk punt na aankoop van elk apparaat Wilton 4210 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Wilton 4210 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Wilton 4210 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Wilton 4210 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Wilton 4210 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Wilton 4210 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Wilton 4210 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Wilton 4210 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
