Gebruiksaanwijzing /service van het product WS-38 van de fabrikant Windster
Ga naar pagina of 27
OPERA TION Please read and save this guide through before using your range hood. Store the guide away in a safe place so that you will know where it is, when you want to refer to it.
Table of Contents Important Safety Instructions ---------------------------- Safety Notes ------------------------------------------------- Tools and Materials Required ----------------------------- A.
Read and Save These Instructions CAUTION - To reduce risk of fire and to properly exhaust air, make sure to properly exhaust air. Be sure to duct air outside- Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces, or garages.
W ARNING - To reduce the risk of injury in the event of a range top grease fire, observe the following: A- with a close- fitting lid, cookie sheet, or metal tray, then turn off the burner. Be careful to prevent burns. If the flames do not go out immediately, SMOTHER FLAMES EVACUATE AND CALL THE FIRE DEPARTMENT.
1. All electrical work must be done in accordance with local and/or national electrical code as applicable for safety. This product must be grounded if your are unfamiliar with methods of installing electrical wiring, secure the services of a qualified electrician.
Drill, electric of ratchet driver, with 3/16" wood bit (for drilling starter holes and 1 ” wood bit (to drill an access holes in the cabinet or kitchen wall for the electric power line) ¼ Plier (for opening electrical knockout).
1. Remove the top electrical knockout, you may plan to bring power to the range hood either through the cabinet or through the wall (Fig.1) 2. Insert a screwdriver into the knockout slot and bend the knockout back and forth. (Fig.2) 3. You may have to use pliers to pull the loosened knockout free.
1. If you want to move the electric range to make room for working on the cabinet turn off the 220 volt power for the electric range at the service entrance. 2. Before moving a gas range, shut off the gas. NOTE: SKIP FOLLOWING STEPS 3A THROUGH 3D IF THE HOOD IS TO BE MOUNTED ON A CABINET WITH .
C. Screw the four 1" wood screws (for mounting the hood) into the exact center of the arrow and into the keyhole mounting slots marked on the cabinet bottom (for flush installations), or marked on the 1” recessed cabinet installation) (Fig.7) Do not turn the mounting screws in all the way.
4. Pick up the inner oil collector. NOTE : Reinstalling Baffle filters. Reverse the steps as removing Baffle filters. For mounting under cabinet 1. After above step H, then continue the following steps. 2. Remove 2 screws on the spacer(s). 3. Remove spacer(s).
2. After using the machine, wipes the machine by neutral detergent in order to keep it clean and maintain the appearance with brightness and sanitation. 3. When the level of dirty oil of the collector reached 4/5 of height, it has to be removed in order to avoid overflowing and pollution.
10 F. Completely finished . A. Remove the pre-mounted 6” round duct opening. B. Put transition plate by first installing on the half round section. (Optional) 4 screws C. Take the rectangular starting collar. (Optional) D. Overlap the rectangular starting collar on the top of transition plate.
11 A. Remove the pre-mounted 6” round duct opening. B. Put transition plate by first installing on the half round section. (Optional) 4 screws C. Use slotted screw driver, (or whatever flat head) to knock out the pre-mounted rear rectangular cap. D.
12 F. Take the pre-mounted rectangular plate. H. Insert appropriate rectangular starting collar (optional) (2 different size) ¼ ¾ ( LxWxH ) 1 1 ¼ ”x3 ¾ ”x3 ( LxWxH ) ⓐ ⓑ⅛ " 1 1 "x3 "x1 " I. Mount rectangular starting collar.
1. Position the hood in place so that : 2. Adjust the hood so the front is flush with the cabinet front. a. The electrical line is routed through the appropriate Knockout opening. This step will have to be accomplished while positioning the hood (Fig.
1. Using metal brackets and screws (included), center hood onto board and install screw. 2. Remove the hood from the board and nail the wood board onto the wall. (Be sure the nail is in the center of the stud) 3. Place the range hood on the board and tighten the screw.
1. Remove stainless Baffle filters. ( Ref.P8-H) 2. Remove screws on wiring case, fish out wires through the knockout. (Fig.12) 3. Mark the electrical connection by fastening all wires to the existing wall wiring according to the their colors. (Black to Black, White to White, Green to Ground) 4.
16 2. : Fan speed selection and fan off. A. : When the main power button is being pressed, by pressing button / / for desired fan speed. - slow speed - medium speed - high speed B. : To turn off the fan, just press the button, or press off the main power button.
Note: Care Instruction : Care Instruction : 17 Range hood should be turn on either before or the same time when cooking begins. After cooking, range hood should be kept on for about 3 more minutes for complete ventilation of cooking odor.
Correction Symptom Fan are not operatable. I lluminating LED light does not work A. Check power source to see if it is normal. A. Disconnect the power source. Hood vibrates. A. Check for damaged vanes. B. Check power inlet plug to see if it is plugged firmly into it's socket.
T . Parts Layout Diagram T. Parts Layout Diagram 19 1 4 3 2 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20.
20 Parts List Parts List Description Hood casing Air chamber Top plate 6” round vent ( ) Motor housing Inner vent (Rear ventilation) Motor (s) Fan (s) Oil tunnel * Spacer (s) * Baffle filter (s) * Handle (s) Oil collector * LED light LED light fixture Control panel Control button LED driver Bracket Wiring partition Vertical ventilation No.
NOTE : Any faults with this unit should only be attended to by a qualified technician. U. Circuit Diagram U. Circuit Diagram 21 Voltage : 110V/60Hz Power consumption : maxi 170W (Motor + LED light) MO.
V. S i z e V. Size 22 15" 11" 5" 9 2 12" 26 2-1/2" 22-7/16" 12” 26° 22-7/16” 2-1/2” 92° 15” 11 ” 5” 8-3/8” 5” 2° 30”(36”)(42”)(48”) 22-7/16” .
What Is Not C overed By These Warranti es: 1) Conditions and damages resulting from any of the following: ? Improper installation, delivery , or ma intena nce. ? A n y repa ir, m odification, a lteration or adjustment not a uthorized by the manufac turer or an auth oriz ed service dea lers.
Def ective Products: A ll produc ts will be inspected, tested, and carefully pac ked by t he m anufac turer before shipping to custome rs. Products tha t ar e damaged during transit can only be exchanged for the sa me product, under the condition t hat the custo mer must get a RMA (Return Merchandise Authorization) from Windster.
2102 N. Seaman Ave., S. El Monte, CA 91733 TEL:(626)350-1015 (626)350-5215 FAX:(626)350-1254 © 2006-2008 Windster Hoods, Inc. Specifications subject to change without notice.
Een belangrijk punt na aankoop van elk apparaat Windster WS-38 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Windster WS-38 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Windster WS-38 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Windster WS-38 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Windster WS-38 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Windster WS-38 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Windster WS-38 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Windster WS-38 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
