Gebruiksaanwijzing /service van het product RX-485 van de fabrikant Yamaha
Ga naar pagina of 20
IMPORTANT! Please record the serial number of this unit in the space below. Model: Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
2 1 Read Instructions – All the safety and operating instructions should be read before the unit is operated. 2 Retain Instructions – The safety and operating instructions should be retained for future reference. 3 Heed Warnings – All warnings on the unit and in the operating instructions should be adhered to.
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
4 Indoor FM Antenna AM Loop Antenna Remote Control Transmitter Batteries (size AA, R6, UM-3) SUPPLIED A CCESSORIES After unpacking, check that the following parts are contained. This product complies with the radio frequency interference requirements of the Council Directive 82/499/EEC and/or 87/308/EEC.
5 ANTENNA CONNECTIONS ● Each antenna should be connected to the designated terminals correctly, referring to the following figure. ● Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength.
6 Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other components to which connections are being made.
7 * : Refer to “ ABOUT THE ACCESSORY TERMINALS ” on page 8. RX-385 R L A B 75 Ω UNBAL PHONO CD AUX A B FM ANT GND AM ANT TAPE PB REC OUT TAPE 1 SPEAKERS Video cassette player etc.
8 Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut to be as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is, + and – markings are observed.
9 1 Set to the “ ∞ ” position. 2 3 Select a desired input source. * The name of the selected input source will appear in the display. * Note that pressing on each input selector button selects the source which is connected to the corresponding input terminals on the rear panel.
10 1 Select the source to be recorded. * To dub from tape to tape, refer to the “ Notes ” shown below. * When you select AUX , TUNER , CD or PHONO , be sure that TAPE 1 and/or TAPE 2 are not also selected. 2 Play the source and then turn the VOLUME control up to confirm the input source.
11 Using the PURE DIRECT switc h RX-485 only You can enjoy the purest possible sound from your audio sources by setting this switch ON. By doing so, the audio signal bypasses the BASS , TREBLE , BALANCE and LOUDNESS controls, eliminating any alterations to the audio signal.
12 FM/AM AM FM 1 Select the reception band (FM or AM) while watching the display. 2 3 Tune to a desired station manually. * To continue tuning search, press and hold the button. 1 Select the reception band (FM or AM) while watching the display. 2 3 To tune to a higher frequency, press the right side once.
13 1 1 Select the page where the preset station is stored. 2 2 Select the preset station number. 1 Tune to a desired station. (Refer to the previous page for tuning procedures.) 2 3 Select a desired page (A – E) of preset stations while watching the display.
14 A UT OMA TIC PRESET TUNING You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on page 13.
15 1 Recall the preset station on E1 (by following the method of “To recall a preset station” on page 13). 2 3 Next, recall the preset station on A5 by following the same method with step 1.
16 REMO TE CONTR OL TRANSMITTER The remote control transmitter provided with this unit is designed to control all the most commonly used functions of the unit. If the CD player, turntable and tape deck connected to this unit are YAMAHA components, then this remote control transmitter will also control various functions of each component.
17 NO TES ABOUT THE REMO TE CONTROL TRANSMITTER Battery installation Battery replacement If you find that the remote control transmitter must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. Notes ● Use only AA, R6, UM-3 batteries for replacement.
18 If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help.
19 SPECIFICA TIONS AUDIO SECTION Minimum RMS Output Power per Channel 8 ohms, 20 Hz to 20 kHz, 0.04% THD < RX-485 > .....................................65W+65W < RX-385 > [U.S.A. and Canada models] .......45W+45W [Australia, U.K., Europe and General models] .
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.
Een belangrijk punt na aankoop van elk apparaat Yamaha RX-485 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Yamaha RX-485 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Yamaha RX-485 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Yamaha RX-485 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Yamaha RX-485 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Yamaha RX-485 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Yamaha RX-485 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Yamaha RX-485 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
