Gebruiksaanwijzing /service van het product CHTZ6010 van de fabrikant Zenoah
Ga naar pagina of 24
HTZ7510 CHTZ6010 848D3L93A1 (704) OWNER’S MANUAL HEDGE-TRIMMERS • Before using our products, please read this manual carefully to understand the proper use of your unit.
.
SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
4 1. Right handle 2. Fuel tank 3. Starter 4. Left handle 5. Throttle lever 6. Engine switch 7. Muffler 8. Blade 9. Front handle 10. Rear handle 11. Plate receive 12.
English For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake. (a). The port to refuel the "MIX GASOLINE" POSITION: FUEL TANK CAP (b).The direction to close the choke POSITION: AIR CLEANER COVER (c).
6 3. SAFETY PRECAUTIONS ■ BEFORE USING THE MACHINE a. Read this owner's manual carefully to understand how to operate this unit properly. b. This product has been designed for use in trimming l.
3. SAFETY PRECAUTIONS g. Lack of sleep, tiredness, or physical exhaustion results in lower attention spans, and this in turn leads to accidents and injury. Limit the amount of time over which the hedge-trimmer is to be used continuously to somewhere around 30~40 minutes per session, and take 10~20 minutes of rest between work sessions.
8 3. SAFETY PRECAUTIONS ■ WARNING CONSIDERING HANDLING OF FUEL a. The engine of this product is designed to run on a mixed fuel which contains highly flammable gasoline.
3. SAFETY PRECAUTIONS persons, always check the presence and locations of others so as to maintain a distance each person sufficient to ensure safety. c. Make sure that there are no loose screws or bolts, fuel leaks, ruptures, dents, or any other problems which might interfere with safe operation.
10 3. SAFETY PRECAUTIONS ■ KICKBACK SAFETY PRECAUTIONS •A dangerous reaction may occur when the spinning blade contacts a solid object in the critical area. It is called Kick back. As a result, the operator can lose control of the unit which can cause serious or fatal injury.
3. SAFETY PRECAUTIONS d. If the grass gets caught in the blade during operation, or if you need to check the unit or refuel the tank, always be sure to turn off the engine. e. If the blade touches a hard object like a stone, immediately stop the engine and check if something is wrong with the blade.
12 English d. When sharpening, removing, or reattaching the blade, be sure to wear thick, sturdy gloves and use only proper tools and equipment to prevent injury.
English 4. FUEL •G asoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. • Wipe up all spills before starting the engine. •M ake sure to stop the engine and allow it cool before refueling the unit. • Keep open flames away from the area where fuel is handled or stored.
14 [HTZ7510] [CHTZ6010] English 5. OPERATION ■ STARTING THE ENGINE Keep the blades clear of everything around It as they will start moving upon the engine starts. 1. [HTZ7510] Make sure that the throttle lever is at idling position. [CHTZ6010] Release the throttle lever and make sure it is fully back.
English ■ RUNNING IN THE ENGINE During the first 20 working hours, do not use the hedge-trimmer at maximum power for long periods. ■ ADJUSTING IDLING SPEED • Before adjusting the carburetor, clean the air filter and warm up the engine.
F9 F8 English • Use only as much throttle as is needed to do the job. Excessive engine speed is unnecessary. • Avoid cutting thick branches, for which will damage the blades and shorten the life of drive systems. • Tilting the trimmer 5 to 10° to the cutting object will make the job easy and bring a good result.
17 Every Every Every Before 25 50 100 System/compornent Procedure use hours hours hours note after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary see ADJUSTING replace carburetor idle adjusting screw ✔ IDLING SPEED if necessary clean and readjust GAP: 0.
18 English 6. MAINTENANCE F10 F12 F11 Before cleaning, inspecting, or repairing the unit, make sure that the engine has stopped and is cool. ■ BLADE (F10) • Check the blade and the fasteners for looseness, cracking, or bending. • Check the cutting edges and reform with a flat file.
English 6. MAINTENANCE F13 F14 3. Check if the safety lock returns to its original position when you release your hand from safety lock. If you find any defects at the checks above, contact your nearest servicing dealer for repair.
20 English 6. MAINTENANCE F15 F16 F17 ■ FUEL FILTER (F15) When the engine runs short of fuel supply, check the fuel strainer for blockage. ■ WAY OF THE COOLING AIR (F16) This engine is air-cooled. Dust clogging between the inlet port of the cooling air and cylinder fins will cause overheating of the engine.
21 English 6. MAINTENANCE F19 F20 ■ MUFFLER AFTER 100 HOURS OF USE 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent at the same time. (F19) (1) screw driver (2) muffler 2.
English Model name ................ HTZ7510 [CHTZ6010] Type ..............................Reciprocating single-sided [double-sided] dual blades Blade length .............................. 750 [600]mm Engine model ........................... Zenoah GZ23N Displacement .
.
Head Office: 1-9, Minamidai, Kawagoe-city , Saitama, 350-1 192 Japan T elephone: (+81)49-243-1 1 17 T elecopier: (+81)49-243-7197.
Een belangrijk punt na aankoop van elk apparaat Zenoah CHTZ6010 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Zenoah CHTZ6010 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Zenoah CHTZ6010 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Zenoah CHTZ6010 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Zenoah CHTZ6010 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Zenoah CHTZ6010 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Zenoah CHTZ6010 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Zenoah CHTZ6010 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
