Gebruiksaanwijzing /service van het product G5300 van de fabrikant Zenoah
Ga naar pagina of 40
E E E E n n n n g g g g l l l l i i i i s s s s h h h h Operator ’ s manual English Please read the operator’ s manual carefully and make sure y ou understand the instructions bef ore using the machine.
KEY T O SYMBOLS 2 – English Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine.
CONTENTS English – 3 Contents KEY T O SYMBOLS Symbols on the machine: ..................................... 2 Symbols in the operator’ s manual: ....................... 2 CONTENTS Contents ..........................................................
4 – English WHA T IS WHA T? What is what on the c hain saw? 14 15 10 11 12 13 24 23 21 20 19 18 17 16 22 25 26 4 2 5 7 6 8 9 3 27 28 29 30 1 G5300 1 Decompression valv e 2 Star ter handle 3 Adjuster screws carb urettor 4 Stop switch (Ignition on/off s witch.
GENERAL SAFETY PRECA UTIONS English – 5 Bef ore using a new c hain saw • Please read this manual carefully . • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly . • Refuel and star t the chain saw .
GENERAL SAFETY PRECA UTIONS 6 – English pro vide information about which training materials and courses are av ailable. Work is constantly in progress to improv e the design and technology - improv ements that increase your safety and efficiency .
GENERAL SAFETY PRECA UTIONS English – 7 • This mov ement activates a spring-loaded mechanism that tightens the brake band (C) around the engine drive system (D) (clutch drum). • The front hand guard is not designed solely to activate the chain brake .
GENERAL SAFETY PRECA UTIONS 8 – English Will m y hand always activ ate the chain brake during a kickbac k? No . It takes a certain force to move the hand guard forw ard. If your hand only lightly touches the front guard or slips ov er it, the force ma y not be enough to trigger the chain brake .
GENERAL SAFETY PRECA UTIONS English – 9 Stop switch Use the stop switch to s witch off the engine. Muffler The muffler is designed to keep noise le vels to a minim um and to direct exhaust fumes a wa y from the user. In areas with a hot, dry climate there is a high r isk of fires.
GENERAL SAFETY PRECA UTIONS 10 – English Cutting equipment designed to reduce kickbac k The only w a y to avoid kic kback is to make sure that the kickbac k zone of the bar nev er touches anything.
GENERAL SAFETY PRECA UTIONS English – 11 Sharpening your c hain and adjusting depth gauge setting General inf ormation on sharpening cutting teeth • Nev er use a blunt chain. When the chain is b lunt you hav e to ex er t more pressure to force the bar through the wood and the chips will be very small.
GENERAL SAFETY PRECA UTIONS 12 – English General ad vice on adjusting depth gauge setting • When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. T o maintain optimal cutting performance the depth gauge (B) has to be filed down to achie ve the recommended depth gauge setting.
GENERAL SAFETY PRECA UTIONS English – 13 Lubricating cutting equipment Chain oil Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather . We recommend the use of our o wn oil for both maximum chain life and to minimise en vironmental damage.
GENERAL SAFETY PRECA UTIONS 14 – English Chain drive spr oc ket The clutch drum is fitted with one of the following driv e sprock ets: A Spur sprock et (the chain sprocket is welded on the drum) B Rim sprock et (replaceable) Regularly check the degree of wear on the drive sproc ket.
ASSEMBL Y English – 15 Fitting the bar and chain Chec k that the chain brak e is in disengaged position by moving the front hand guard tow ards the front handle. Remov e the bar nuts and remove the clutch co ver (chain brake). T ake off the transportation ring (A).
FUEL HANDLING 16 – English Fuel Note! The machine is equipped with a two-stroke engine and must alwa ys be run using a mixture of petrol and two- stroke oil. It is impor tant to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained.
FUEL HANDLING English – 17 • In temperatures below 0 ° C (32 ° F) some oils become too viscous. This can o verload the oil pump and result in damage to the oil pump components. • Contact your service agent when choosing chain oil. Fuelling Clean the area around the fuel cap .
ST ARTING AND ST OPPING 18 – English Star ting and stopping Cold engine Starting: The chain br ake must be engaged when the chain saw is started. Activate the brak e by moving the front hand guard forw ards. Ignition; choke: Set the choke control in the choke position.
ST ARTING AND ST OPPING English – 19 As the chain br ake is still engaged the speed of the engine must be set to idling as soon as possible , this is achiev ed by quic kly disengaging the throttle lock. This prev ents unnecessary wear to the clutch, clutch dr um and brake band.
WORKING TECHNIQUES 20 – English Bef ore use: 1 Check that the chain brak e works correctly and is not damaged. 2 Check that the rear right hand guard is not damaged. 3 Check that the throttle loc kout works correctly and is not damaged. 4 Check that the stop s witch works correctly and is not damaged.
WORKING TECHNIQUES English – 21 6 Before mo ving your chain saw s witch off the engine and lock the chain using the chain brak e. Carr y the chain saw with the bar and chain pointing bac kwards. Fit a guard to the bar before tr anspor ting the chain saw or carrying it for any distance .
WORKING TECHNIQUES 22 – English 7 T ake great care when you cut with the top edge of the bar , i.e. when cutting from the underside of the object. This is known as cutting on the push stroke . The chain tries to push the chain saw back to wards the user .
WORKING TECHNIQUES English – 23 T wo factors decide whether the chain will jam or the object that you are cutting will split: the first is how the object is suppor ted before and after cutting, and the second is whether it is in tension. In most cases you can a void these problems b y cutting in two stages; from the top and from the bottom.
WORKING TECHNIQUES 24 – English Star t by cutting from abo ve (about 1/3 of the wa y through). Finish by cutting from below so that the tw o cuts meet. T ree felling technique Safe distance The saf e distance betw een a tree that is to be felled and anyone else w orking nearby is at least 2 1/2 tree lengths.
WORKING TECHNIQUES English – 25 Remo v e any undergrowth from the base of the tree and check the area f or obstacles (stones, branches, holes , etc.) so that you ha ve a clear path of retreat when the tree star ts to fall. Y our path of retreat should be roughly 135 degrees aw ay from the intended f elling direction.
WORKING TECHNIQUES 26 – English Finish the felling cut par allel with the directional cut line so that the distance between them is at least 1/10 of the trunk diameter. The uncut section of the trunk is called the felling hinge . The felling hinge controls the direction that the tree f alls in.
WORKING TECHNIQUES English – 27 Cutting trees and branches that are in tension Prepar ations: Work out which side is in tension and where the point of maximum tension is (i.e. where it would break if it was bent e ven more). Decide which is the safest w ay to release the tension and whether you are ab le to do it safely .
WORKING TECHNIQUES 28 – English Limbing Mak e sure that y ou can stand and move about saf ely . Work on the left side of the trunk. Work as close as possible to the chain sa w for maximum control. If possible, let the weight of the chain saw rest on the trunk.
MAINTENANCE English – 29 General The user must only carry out the maintenance and service work descr ibed in this manual. Carb urettor adjustment Due to existing en vironmental and emissions legislation your chain sa w is equipped with movement limiters on the carburettor adjuster scre ws.
MAINTENANCE 30 – English High speed jet H At the factor y the engine is adjusted at sea level. When working at a high altitude or in different weather conditions, temperatures and atmospheric humidity , it ma y be necessary to make minor adjustments to the high speed jet.
MAINTENANCE English – 31 Chec king the inertia brake release Place the chain saw , with the engine switched off , on a stump or other stable surf ace. Release the front handle and let the saw f all by its own w eight, rotating around the rear handle towards the stump .
MAINTENANCE 32 – English Chain catcher Chec k that the chain catcher is not damaged and is firmly attached to the body of the chain saw . Right hand guard Chec k that the right hand guard is not damaged and that there are no visible def ects, such as crac ks.
MAINTENANCE English – 33 Starter Changing a broken or w orn starter cord • Loosen the screws that hold the starter against the crankcase and remov e the star ter . • Pull out the cord approx. 30 cm and hook it into the notch in the rim of the pulley .
MAINTENANCE 34 – English Air filter The air fi lter must be regularly cleaned to remov e dust and dir t in order to av oid: • Carburettor malfunctions • Star ting problems • Loss of engine power • Unnecessary wear to engine par ts. • Excessive fuel consumption.
MAINTENANCE English – 35 Adjustment of the oil pump The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner .
36 – English MAINTENANCE Maintenance schedule The follo wing is a list of the maintenance that must be performed on the machine. Most of the items are descr ibed in the Maintenance section. Dail y maintenance Weekl y maintenance Monthly maintenance Clean the outside of the machine .
English – 37 TECHNICAL D A T A T echnical data Note 1: Noise emissions in the environment measured as sound power (L W A ) in conformity with EC directive 2000/14/EC .
38 – English TECHNICAL D A T A Bar and chain combinations The f ollo wing recommended combinations of bar and saw chain are type approv ed for y our chain saw . Saw c hain filing and file gauges F or file gauges , see recommendations from manufacturer (www .
LIMITED W ARRANTY English – 39 Limited warranty Should an y f ailure occur on the product under nor mal operating conditions within the applicable w arranty period, the failed part will be replaced or repaired free of charge by a ZENO AH authorized dealer.
1151331-26 ´®z+SA,¶6y¨ ´®z+SA,¶6y¨ 2008-11-03.
Een belangrijk punt na aankoop van elk apparaat Zenoah G5300 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Zenoah G5300 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Zenoah G5300 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Zenoah G5300 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Zenoah G5300 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Zenoah G5300 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Zenoah G5300 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Zenoah G5300 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
