Gebruiksaanwijzing /service van het product SRTZ2500 van de fabrikant Zenoah
Ga naar pagina of 32
OWNER / OPERA T OR MANUAL SHOR T REA CH TRIMMER 848-A2A-93A1 (501) SRTZ2500 The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING Before using our trimmers, please read this manual carefully to understand the proper use of your unit.
INFORMA TION This machine is equipped with an Overload Cancellation Mechanism. When the cutting blades have got into metal wires or those twigs difficult to cut, the mechanism acts as a shock absorber , and protects the drive gears and the blades from severe reaction which could give damage to those parts.
SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
2. Specifications ■ SRTZ2500 Overall size(LxWxH) ························································ 67.
5 (1) Read owner's manual before operating this machine. (2) Wear head, eye and ear protection. (3) Handling this machine improperly could result in accidents causing serious injury or death.
6 For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake.
5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product.
8 b. At night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the working area.
■ BEFORE STARTING THE ENGINE 1. The area within a perimeter of 50 feet (15m) of the person using the product should be considered a hazardous area into which no one should enter. If necessary yellow warning rope, warning signs should be placed around the perimeter of the area.
10 Never place the throttle into the high speed position when starting the engine. 3. After starting the engine, check to make sure that the cutting attachment stops rotating when the throttle is moved fully back to its original position.
• IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around.
12 5. For safe operation ■ HANDLING FUEL 1. The engine of the RedMax product is designed to run on a mixed fuel which contains highly flammable gasoline.
■ MOUNTING ENGINE (SE1) 1. Push the driveshaft housing toward the clutch housing and rotate it by hand to check that the driveshaft is engaged with the gears. 2. Insert the driveshaft housing into the clutch housing until it bottoms, and align the positioning holes on the clutch housing and the shaft tube and install the screw.
14 6. Set up SE4 ■ ATTACHING THE TRIMMING MECHANISM (SE4) 1. Remove the cap on the end of the main pipe. 2. Remove the screw screwed into the end of the trimming mechanism.
■ RECOMMENDED MIXING RATIO GASOLINE 50:OIL 1 • Exhaust emission are controlled by the fundamental engine parameters and components(eq., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion.
16 7. Fuel again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture.
■ STARTING ENGINE The cutting head will start rotating upon the engine starts. 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine. 2. Push the primer pump several times until overflown fuel flows out in the clear tube.
18 8. Operation ■ STOPPING ENGINE (OP3) 1. Release the throttle lever and run the engine for a half minute. 2. Shift the ignition switch to the STOP position. • Except for an emergency, avoid stopping the engine while pulling the throttle lever.
handling can cause accidents which may in turn lead to serious injury or death. For this reason, you should always be careful to follow the following instructions when using your trimmer. • Never hold the trimmer in a way in which the blades are pointed towards someone else.
20 9. Maintenance ■ BLADES (MA1) •W hen refilling the tank or resting, it is often a good idea to use the time to oil the cutting blades. • If a gap exists between the upper and lower blades, follow the procedure below to adjust them so that they fit more closely together.
QUICK TIP If the blades become so worn down that it is no longer possible to eliminate the gap between them, you should contact the authorized RedMax servicing dealer from which you purchased your RedMax® trimmer to have the blades resharpened or replaced.
22 ■ SPARK PLUG • Starting failure and mis-firing are often caused by a fouled spark plug. Clean the spark plug and check that the plug gap is in the correct range. For a replacement plug, use the correct type specified by RedMax. (MA5) • REPLACEMENT PLUG IS A NGK CMR7A.
9. Maintenance ■ INTAKE AIR COOLING VENT •N ever touch the cylinder, muffler, or spark plugs with your bare hands immediately after stopping the engine.
11 . T roubleshooting guide Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank ➞ incorrect fuel ➞ drain it and with correct fuel fuel filter ➞ fuel filter is clogged ➞ clean carbu.
Jun. 2003 12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company.
12. Parts list 26 Fig.1 DRIVE UNIT SRTZ2500 (S/N 000000 and up) Fig.2 CUTTING UNIT SRTZ2500 (S/N 000000 and up).
Fig.2 CUTTING UNIT SRTZ2500 (S/N 000000 and up) Fig.1 DRIVE UNIT SRTZ2500 (S/N 000000 and up) Key# Description Part Number Q'ty 1P IPE COMP. T3075-12100 1 2 SHAFT T3075-12210 1 3 GRIP 3577-32141 1 4L EVER COMP.
Fig.3 ENGINE UNIT SRTZ2500 (S/N 50100000 and up) 28 12. Parts list.
Fig.3 ENGINE UNIT SRTZ2500 (S/N 50100000 and up) 29 Key# Description Part Number Q'ty 1 CYLINDER 4810-12111 1 2 GASKET, base 4810-12210 1 3 BOLT 1850-12130 2 4 INSULATOR 4810-13162 1 5 GA.
EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP.
Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera.
KOMATSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093 ©P rinted in Japan.
Een belangrijk punt na aankoop van elk apparaat Zenoah SRTZ2500 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Zenoah SRTZ2500 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Zenoah SRTZ2500 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Zenoah SRTZ2500 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Zenoah SRTZ2500 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Zenoah SRTZ2500 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Zenoah SRTZ2500 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Zenoah SRTZ2500 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
