Gebruiksaanwijzing /service van het product PCW22A-R3 van de fabrikant Black Box
Ga naar pagina of 33
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500 ) FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 Mailing address: Black Box Corporation , 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.
FCC ST A TEMENT 1 FEDERAL COMMUNICA TIONS COMMISSION AND INDUSTR Y CANADA RADIO FREQUENCY INTERFERENCE ST A TEMENTS This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly , that is, in strict accordance with the manufacturer’ s instructions, may cause inter ference to radio communication.
PROTOCOL CONVER TER A/S-2G 2 INSTRUCCIONES DE SEGURIDAD (Normas Oficiales Mexicanas Electrical Safety Statement) 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
T ABLE OF CONTENTS 3 T able of Contents 1.0 Specifications .......................................................................................................................................5 2.0 Introduction ......................................
PROTOCOL CONVER TER A/S-2G 4 4.2 Synchronous Device to Asynchronous Device ........................................................................22 4.2.1 Line Control ..................................................................................
CHAPTER 1: Specifications 5 1.0 Specifications Protocol — Asynchronous: TTY (ASCII) Bisynchronous: 2770, 2780, 3741, and 3780 (EBCDIC) Por ts — A: Asynchronous B: Synchronous/bisynchronous Speed — Up to 19.
PROTOCOL CONVER TER A/S-2G 6 2.0 Introduction The Model A/S-2G provides compatibility between an asynchronous, ASCII coded device and a synchronous, EBCDIC coded device. It is desirable, prior to installation, to review the following checklist to ensure the appropriateness of all the devices in the system for the planned application.
CHAPTER 3: Installation 7 3.0 Installation 3.1 UNP ACKING AND INSPECTION After unpacking the A/S-2G, inspect it for shipping damage. Should there be any noticeable damage, save the cartons and contact the carrier who delivered the box to place a freight damage claim.
PROTOCOL CONVER TER A/S-2G 8 Block size for the 2770/2780 is normally limited to 160, but block size is 400 if the 2770/2780 has the Multiple Record T ransmission.
CHAPTER 3: Installation 9 Switch #4 ON = Self-Diagnostics Mode. OFF = Normal Operation. Switch #5, #6 —Block Size Specification. 56 OFF OFF 80 Characters OFF ON 128 Characters ON OFF 256 Characters .
PROTOCOL CONVER TER A/S-2G 10 NOTE Self-diagnostics will normally display the switches as they are set on the printed circuit board. If the switches were reconfigured (see Section 3.2.4), the switches will be displayed as they are set in the software.
CHAPTER 3: Installation 11 If SW3, Switch #7 is ON, the A/S-2G will drop DTR when only 32 character spaces remain in the buffer . The A/S-2G will reassert DTR as soon as there are at least 33 character spaces available. For most applications, it is best to configure SW3, Switch #7 ON.
PROTOCOL CONVER TER A/S-2G 12 3.3.5 CARRIER OPTIONS If the carrier detect signal is to be driven by the A/S-2G configuration (DCE), the jumper labeled CAR A ENB must be installed. CAR A ENB is located below U20. Refer to the printed circuit board, Figure 5-2, on page 28.
CHAPTER 3: Installation 13 there is data to be transmitted. Once the A/S-2G receives CTS from the attached device, it will transmit the data. When the synchronous port (Port B) is configured as DTE, the CTS B jumper must be placed over the CNT position.
PROTOCOL CONVER TER A/S-2G 14 3.4.8 COMMAND P ASS-THRU T o use the command pass-thru feature, the command must be preceded by &% and terminated by &% . Example: &% - Command - &% Commands consist of character pairs. Each pair must represent a valid Hexidecimal value (i.
CHAPTER 4: Operation 4.0 Operation By its nature, a protocol converter must operate differently in each direction, since it is communicating with separate devices. Therefore, its operation will be discussed separately for asynchronous to synchronous operation and for synchronous to asynchronous.
PROTOCOL CONVER TER A/S-2G 16 In 3741 protocol, each block contains only one record. If SW3, Switch #5 is OFF , the A/S-2G will fill the block with spaces until it reaches 128 characters . If SW3, Switch #5 is ON, the block will end immediately after CR.
CHAPTER 4: Operation 17 If SW3, Switch #7 is OFF , the A/S-2G will send an X-OFF (ASCII DC3, 13 Hex) to the asynchronous device when RAM reaches a nearly-full state. This prevents data from being lost due to a buffer overrun. When RAM space is available, the A/S-2G will send an X-ON (ASCII DC1, 11 Hex) to resume transmission.
PROTOCOL CONVER TER A/S-2G 18 Data Flow — A/S-2G to Synchronous Device Bisynchronous Device A/S-2G Converter Asynchronous Device *Assumes block size of 80 is selected. IF 2270 - 2780 AA AA 32 32 32 32 02 (text up to 80 characters), IF , BCC1, BCC2; etc.
CHAPTER 4: Operation 19 Data Flow — A/S-2G to Synchronous Device Bisynchronous Device A/S-2G Converter Asynchronous Device ACK 1 NAK Negative Acknowledgment AA AA 32 32 32 32 3D FF FF ACK 0 WA K AA AA 32 32 32 32 6B FF FF Holds up transmission while buffer clears DC3 (ASCII 13 Hex) or drop DTR CTS or user -specified lead Frees up buffer space.
PROTOCOL CONVER TER A/S-2G 20 Data Flow — A/S-2G to Synchronous Device Bisynchronous Device A/S-2G Converter Asynchronous Device WA K ACK 1 ACK 0 AA 32 32 32 32 02 2D FF FF NAK AA AA 32 32 32 32 3D .
CHAPTER 4: Operation 21 Data Flow — A/S-2G to Synchronous Device Bisynchronous Device A/S-2G Converter Asynchronous Device *Assumes block size of 80 is selected.
PROTOCOL CONVER TER A/S-2G 22 4.2 SYNCHRONOUS DEVICE TO ASYNCHRONOUS DEVICE 4.2.1 LINE CONTROL When the A/S-2G is initially connected to an AC power source or reset, the synchronous device can gain control of the line by sending an ENQ.
CHAPTER 4: Operation 23 Should the A/S-2G receive a DLE EOT (disconnect), the A/S-2G will cycle the synchro-nous DTR lead off for 2 seconds. This action will disconnect a phone line if the DTR B jumper is set for CNT .
PROTOCOL CONVER TER A/S-2G 24 Data Flow — A/S-2G to Asynchronous Device Bisynchronous Device A/S-2G Converter Asynchronous Device ENQ Send data block A Send data block B ENQ ENQ Send data block C Un.
CHAPTER 4: Operation 25 Data Flow — A/S-2G to Asynchronous Device Bisynchronous Device A/S-2G Converter Asynchronous Device Send data block D Send data block D Send data block E Retransmit block E T.
PROTOCOL CONVER TER A/S-2G 26 Data Flow — A/S-2G to Asynchronous Device Bisynchronous Device A/S-2G Converter Asynchronous Device Send data block F (last block) EOT ACK 0 Send block F Send C R LF EO.
CHAPTER 5: Conversions and Connections 27 5.0 Conversions and Connections 5.1 TRANSP ARENCY MODE OF OPERA TION With a special transparency PROM installed, the A/S-2G will communicate with a host system in IBM binary synchronous transparent mode. T o special-order the transparency PROM, please call technical support.
PROTOCOL CONVER TER A/S-2G 28 5.3 RS-232 CABLE CHAR T RS-232C pins are defined as follows: 1 = Chassis (or Frame or Protective) Ground F-GND, C-GND, or P-GND 2 = T ransmit Data TD or TXD 3 = Receive D.
CHAPTER 5: Conversions and Connections 29 5.4 CODE CONVERSIONS The conversions used in the standard 2770, 2780, 3741, and 3780 PROMs are shown in the following charts. Y our PROM can be customized. Please call T echnical Support if you have particular translation requirements.
PROTOCOL CONVER TER A/S-2G 30 Character or ASCII EBCDIC Graphic Hex Dir. Hex Comments @4 0 7 C A4 1 C 1 B4 2 C 2 C4 3 C 3 D4 4 C 4 E4 5 C 5 F4 6 C 6 G4 7 C 7 H4 8 C 8 I4 9 C 9 J4 A D 1 K4 B D 2 L4 C D.
CHAPTER 5: Conversions and Connections UNASSIGNED EBCDIC CODE 04 2B 46 58 71 8D AB B7 CE ED 08 30 47 59 72 8E AC B8 CF EF 09 31 48 62 73 8F AE B9 DA FA 17 34 49 63 74 90 AF BA DB FB 1A 38 51 64 75 9A .
1000 P ark Drive • Lawrence, P A 15055-1018 • 724-746-5500 • F ax 724-746-0746 © Copyright 1998. Black Box Corporation. All rights reserved..
Een belangrijk punt na aankoop van elk apparaat Black Box PCW22A-R3 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Black Box PCW22A-R3 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Black Box PCW22A-R3 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Black Box PCW22A-R3 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Black Box PCW22A-R3 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Black Box PCW22A-R3 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Black Box PCW22A-R3 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Black Box PCW22A-R3 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
