Gebruiksaanwijzing /service van het product SW590A-R2 van de fabrikant Black Box
Ga naar pagina of 23
Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 Mail order: Black Box Corporation , 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.
FEDERAL COMMUNICA TIONS COMMISSION AND INDUSTR Y CANADA RADIO FREQUENCY INTERFERENCE ST A TEMENTS This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication.
Chapter Page 1 Specifications .............................................................................................................4 2 Introduction ...............................................................................................
Interface — RS-232 asynchronous (each port individually selectable for DTE or DCE) Connectors — Switch: (5) DB25S female; Switch with Expansion Board: (9) DB25S female Pins Suppor ted — 1-8, 20,.
The Code Operated Switch II (COS II) makes code-operated switching possible for diverse combinations of serial devices. As it switches, the COS II also reconciles differences in word size, speed, flow control, and parity for up to four devices. An Expansion Board, available separately , doubles the maximum number of devices, to eight.
3.1. Introduction In addition to this manual, your Switch package should contain one standard switch unit and a wallmounted power supply . After you’ve unpacked the Switch, take a few minutes to look through this manual.
The board layout for the Four -Port Expansion Board is shown on this page (Fig. 2). If you have ordered one, check your Board to make sure it matches. NOTE: Every time you change the DIP switch settings, you must press the reset button located on the front panel of the switch, or unplug the power supply.
In addition, there are some system characteristics that are set with the eighth DIP switch of the individual port switch banks. Sections 3.6 and 3.7 explain these functions in depth.
Automatic Timeout The COS II times the inter vals between the reception of each character and the next. Y ou may instruct it to return to an unlinked state after inter vals of 2.5, 5, or 10 minutes, or you may disable this automatic timeout feature. SWF 5 and SWF 6 control this feature.
3.6.2 S ETTING THE A RMING C HARACTER WITH SWG Switch Bank SWG supplies a portion of the control-code sequence, the sequence that activates the Switch. The arming character , the ASCII code that alerts the COS-II to an upcoming switch action, is set with SWG.
ARMING CHARACTER SWITCH POSITIONS LSB MSB ASCII CTRL HEX DECIMAL 1 2 3 4 5 6 7 8 ’ 27 39 ON ON ON OFF OFF ON OFF OFF ( 28 40 OFF OFF OFF ON OFF ON OFF OFF ) 29 41 ON OFF OFF ON OFF ON OFF OFF * 2A 42 OFF ON OFF ON OFF ON OFF OFF + 2B 43 ON ON OFF ON OFF ON OFF OFF , 2C 44 OFF OFF ON ON OFF ON OFF OFF - 2D 45 ON OFF ON ON OFF ON OFF OFF .
CODE OPERA TED SWITCH II 12 ARMING CHARACTER SWITCH POSITIONS LSB MSB ASCII CTRL HEX DECIMAL 1 2 3 4 5 6 7 8 S 53 83 ON ON OFF OFF ON OFF ON OFF T 54 84 OFF OFF ON OFF ON OFF ON OFF U 55 85 ON OFF ON .
ARMING CHARACTER SWITCH POSITIONS LSB MSB ASCII CTRL HEX DECIMAL 1 2 3 4 5 6 7 8 80 128 OFF OFF OFF OFF OFF OFF OFF ON 81 129 ON OFF OFF OFF OFF OFF OFF ON 82 130 OFF ON OFF OFF OFF OFF OFF ON 83 131 .
ARMING CHARACTER SWITCH POSITIONS LSB MSB ASCII CTRL HEX DECIMAL 1 2 3 4 5 6 7 8 AE 174 OFF ON ON ON OFF ON OFF ON AF 175 ON ON ON ON OFF ON OFF ON B0 176 OFF OFF OFF OFF ON ON OFF ON B1 177 ON OFF OF.
ARMING CHARACTER SWITCH POSITIONS LSB MSB ASCII CTRL HEX DECIMAL 1 2 3 4 5 6 7 8 DF 223 ON ON ON ON ON OFF ON ON E0 224 OFF OFF OFF OFF OFF ON ON ON E1 225 ON OFF OFF OFF OFF ON ON ON E2 226 OFF ON OF.
T o Set SWB 8 Pass breaks ON Ignore breaks OFF Lead Pass-Through This function allows the COS II either to pass hardware-handshake leads to connected devices, or to block them. If they are blocked, the leads will still be used to regulate the 8K internal buffer of the Switch.
3.9. Connecting and Powering Up the COS-II Once you have configured the internal switches and jumpers, you can connect your devices and the wallmounted power jack to the COS-II. Before you begin, you might wish to check the settings of all the DIP switches again, to make sure you have set them correctly .
4.1. Introduction The primary action of the Switch consists of detecting and responding to control-code sequences. As it switches to a particular port, the COS-II establishes a link between the master and the slave device.
4.6. Indicators The front panel of the Switch contains 10 LEDs. The Power LED, at the extreme right, will glow steadily when power is on. The Lockout LED, a green LED at the extreme left, will light when the unit is in lockout. Each of the eight port LEDs, numbered 0 through 7, will respond to the action of the COS II.
CODE OPERA TED SWITCH II After you have hit a key , the screen will change to: Serial Por t T est The Serial Port T est is a loopback test that checks whether data is being correctly transmitted and received on any port. The test also checks, using DTR/CTS/RI or R TS/DCD, whether the box can loop back control leads correctly .
Individual Port Switch Bank Settings Switch Position Setting Option 1 2 3 4 5 6 7 Speed 110 bps ON ON ON 300 bps OFF ON ON 600 bps ON OFF ON 1200 bps OFF OFF ON 2400 bps ON ON OFF 4800 bps OFF ON OFF .
System Switch Options A vailable through Position 8 Switch Option SWA 8 SWB 8 SWC 8 SWD 8 SWE 8 Self-test ON Normal operation OFF Pass breaks ON Ignore breaks OFF Lead pass-through ON Normal operation.
1000 P ark Drive • Lawrence, P A 15055-1018 • 724-746-5500 • F ax 724-746-0746 ©Copyright 1999. Black Box Corporation. All rights reserved..
Een belangrijk punt na aankoop van elk apparaat Black Box SW590A-R2 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Black Box SW590A-R2 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Black Box SW590A-R2 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Black Box SW590A-R2 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Black Box SW590A-R2 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Black Box SW590A-R2 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Black Box SW590A-R2 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Black Box SW590A-R2 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.