Gebruiksaanwijzing /service van het product SW925A van de fabrikant Black Box
Ga naar pagina of 34
1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746 CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S.: Call 877-877-BBOX (outside U.
1 MODULAR SMAR T SWITCH FEDERAL COMMUNICA TIONS COMMISSION AND INDUSTR Y CANADA RADIO FREQUENCY INTERFERENCE ST A TEMENTS This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication.
3 MODULAR SMAR T SWITCH 12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada. 13. Los cables de la fuente de poder deben ser guiados de tal.
5 MODULAR SMAR T SWITCH Contents Chapter Page 1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 MODULAR SMAR T SWITCH Chapter Page Appendix A: Serial Ports ..................................................................................53 A.1 RS-232 and RS-422 Pin Assignments ....................................................53 A.2 Connecting to Computers—RS-232 Connections .
9 MODULAR SMAR T SWITCH 2. Introduction The Modular Smart Switch is suitable for a wide variety of applications, including printer and plotter sharing, file transfer, modem sharing, network switching, electronic point-of-sale systems, access control networks, machine tool control, data collection, and mainframe connections.
11 MODULAR SMAR T SWITCH 3. Installing Memor y and Por t Modules To fit memory and port modules, you will need to remove the lid of your Modular Smart Switch. To do this, remove the four retaining screws holding the lid in place (see Figure 3-2 ) and lift the lid away.
13 MODULAR SMAR T SWITCH Figure 3-2. Fitting Port Modules. To fit port modules: 1. Make sure that the Modular Smart Switch is powered off. 2. Remove the rear- panel blanking plates as appropriate. 3. Insert the modules as shown in Figure 3-2 . 4. Push the modules onto the mating connectors on the base board.
15 MODULAR SMAR T SWITCH 4.1 Setting the Global Timeout Period Figure 4-1. Setting the Global Timeout Period. 0 0 1 1 0 1 0 1 OFF (0) ON (1) 1 2 3 4 5 6 Timeout = 16 seconds Timeout = 30 seconds Timeout = 1 minute Timeout = 4 minutes Reserved - set to 0 TEST switch - set to 0 (OFF) for normal operation 14 MODULAR SMAR T SWITCH 4.
17 MODULAR SMAR T SWITCH 4.2 Setting Parallel Ports as Inputs or Outputs Figure 4-2. Selecting the Direction of Parallel Ports (Input or Output). HIGH port Dual parallel port module LOW port HIGH port.
19 MODULAR SMAR T SWITCH NOTE The XON/XOFF setting for printer and plotter con-nections is a bidirectional protocol that recognizes the XON and XOFF characters in both directions. The XON/XOFF setting for com-puter connections recog-nizes the XON and XOFF characters in one direction only.
21 MODULAR SMAR T SWITCH 5. Installing the Modular Smar t Switch 5.1 Selecting Ports for Y our Equipment Printer and Plotter Sharing Applications Unless otherwise specified, all print and plot data will automatically be routed to port 1. If you are automatically sharing a single printer or plotter, connect it to port 1.
23 MODULAR SMAR T SWITCH MODE COM1:9600,N,8,1,P <enter> This sets the baud to 9600, no parity, 8 bits per character, and 1 stop bit on COM1. You may wish to put this in your computer’s AUTOEXEC.
25 MODULAR SMAR T SWITCH 5.9 Buffer Status Indicators The buffer status indicators show the state of the internal buffer memory in the form of a bar graph: • 1 ⁄ 4 Indicator —Buffer is over 1/4 .
27 MODULAR SMAR T SWITCH 6.3 Command-Line Options The control software supports a number of command line options that allow the utility to be installed and run in several different formats. They also allow a number of default settings to be changed and different hotkey combinations to be selected.
29 MODULAR SMAR T SWITCH To use HOTKEY within Windows, you must first install the control software in your computer’s memory. Do this before you run Windows, because once you are within Windows, resident programs cannot be loaded. You can then activate HOTKEY by clicking on HOTKEY.
31 MODULAR SMAR T SWITCH F. Destination Port—Indicates the port on the Modular Smart Switch that your PC is currently connected to. All data output from the currently selected PC port (G) will be routed to this destination port on the Modular Smart Switch.
33 MODULAR SMAR T SWITCH 6.8 Direct Output of T yped Keyboard Characters Normal keyboard characters and control characters can be sent to the printer using the “Direct Output” option. In the keyboard characters box, all characters typed will be sent directly to the printer except <up>, <down>, and <escape>.
35 MODULAR SMAR T SWITCH When in the functions menu, use the arrows to select END OF FILE and then press <enter>. The dialog box will respond with an END OF FILE message for a few seconds. The END OF FILE function can also be used to end long timeouts.
37 MODULAR SMAR T SWITCH 7. Serial Por t Control Utility The control software allows serial ports on IBM compatible PCs to be run at the high baud rates supported by the Modular Smart Switch. The utility can be used to control COM1 or COM2 and supports a wide range of protocols.
39 MODULAR SMAR T SWITCH OR : b) The Fast Printing Direct to Port option is switched off within Windows 3.1. This can be found within the CONTROL PANEL PRINTERS CONNECT window. 38 MODULAR SMAR T SWITCH Increasing the baud rate of serial connections reduces the maximum cable lengths.
41 MODULAR SMAR T SWITCH Figure 8-1. Main Menu. A=The port on the Modular Smart Switch that is connected to the computer that you wish to exchange files with. B=The port on your computer that is connected to the Modular Smart Switch. C=A flashing arrow to indicate that the Modular Smart Switch is in “file- transfer mode.
43 MODULAR SMAR T SWITCH 8.4 General Hints and Tips 1. Always use the control software when using file-transfer software: Many packages such as Laplink Pro will not operate without the control software installed. 2. File transfer requires a protocol of 8 bits per character, 1 stop bit, no parity, and hardware handshaking.
45 MODULAR SMAR T SWITCH 9.2 Connect Command 9.2.1 S ELECTING A D ESTINATION P ORT By default, the Modular Smart Switch automatically sends all data to port 1. To send data to a different port or route back to port 1, use the following command: <PM CONNECT port> where “port” represents a port number from 1 to 12.
47 MODULAR SMAR T SWITCH <PM CONNECT port SOFTWARE:DISABLE> 9.2.6 R EMOVING L INE F EEDS AT E ND OF S OFTWARE C OMMANDS When programming applications such as DBASE to automatically send data to .
49 MODULAR SMAR T SWITCH 9.6 Sending Default Start-of-Day Destination Ports At the start of each day, each port will be routed through to port 1. However, for IBM compatible PCs, individual start-of-day destinations can be set for each computer. To do this, create a text file containing the desired selection command (see Section 9.
51 MODULAR SMAR T SWITCH 10.4 Problems Interfacing Serial Devices Most problems experienced with connecting serial devices are caused by incorrect cabling or incorrect handshake/protocol settings.
53 MODULAR SMAR T SWITCH Appendix A: Serial Por ts A.1 RS-232 and RS-422 Pin Assignments The serial ports on the Modular Smart Switch use DB25 connectors. The following table lists RS-232 and RS-422 pin assignments and signal descriptions. Those pins not appearing in the table are not used.
55 MODULAR SMAR T SWITCH Figure A-1. IBM PC/XT Serial Cable Pinning. If you already have a cable that works directly between your IBM PC and serial printer, it may be suitable for use as the input cable to your Modular Smart Switch.
57 MODULAR SMAR T SWITCH A.4 Connecting to Modems The cable shown in Figure A-4 can be used to connect to most standard modems. Do not connect additional lines. Figure A-4. Cable Pinout for Modems. Modular Smart Switch end 25-Pin socket connector Printer end 25-pin plug connector 1 2 3 4 5 7 20 1 2 3 4 5 7 20 56 MODULAR SMAR T SWITCH Figure A-2.
59 MODULAR SMAR T SWITCH A.6 Connecting to NEC Spinwriter The NEC Spinwriter ® series of printers also provide a DB25 socket connector for serial data. However, their “printer ready” flow-control signal is output on pin 19 (unlike most printers, which output this signal on pin 20).
61 MODULAR SMAR T SWITCH A.8 RS-422 Cables The pins and connector types used for RS-422 communication vary widely between devices. Standard cables therefore do not exist. Connect the cable as shown in Figure A-8 . For systems using XON/XOFF handshaking, only RXD +, RXD -, TXD +, and TXD - need to be connected.
63 MODULAR SMAR T SWITCH T able B-1. DB25 Parallel Connector Pinouts. Pin Name Input from Computer Output to Printer 1 STROBE INPUT OUTPUT 2-9 DATA 0 to 7 INPUT OUTPUT 10 ACKNOWLEDGE OUTPUT no connect.
64 MODULAR SMAR T SWITCH B.2 Cable for IBM PC, PC/XT , A T , or Compatible Parallel cables to connect from IBM compatibles to the Modular Smart Switch require a 25-pin plug on both ends. All lines should be connected “straight- through” (that is, 1 to 1, 2 to 2, etc.
Een belangrijk punt na aankoop van elk apparaat Black Box SW925A (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Black Box SW925A heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Black Box SW925A vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Black Box SW925A leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Black Box SW925A krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Black Box SW925A bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Black Box SW925A kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Black Box SW925A . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
