Gebruiksaanwijzing /service van het product 56K ISA Lite van de fabrikant Actiontec electronic
Ga naar pagina of 41
.
1 Propr ietar y Notice and Disclaimer U nless otherwise noted, this document and the information herein disclosed are proprietary to A ction- tec Electronics, Inc.
2 Introduction Thank you for purchasing the Action tec 56K ISA Lite internal modem. The Advan- tage incorporates the latest technology in host-based V .90 modems. This new tech- nology provides vast improv ements in both the performance and the capabilities of personal computer fax/modems.
3 Do This Fir st Please read the following tips before attempting to install your new modem. F or Windo ws 95 and Windo ws 98 Installations Be sure to remo ve all other modem drivers from your operating system. T o do this, right-click M y Computer , choose Properties from the menu that appears, then click on the Device Manager tab.
4 If you are going to use the T elephone Answering Machine (T AM) functions of the modem and you are running Windows 95, you need to install a software component called U nimodem V . If you have W indows 95 OEM Se rvice Release 2 (V ersion 4.00.950 B) or a later version of Windows, this component comes standar d as part of the operating system.
5 T o disable COM2, boot your system and enter your BIOS setup. Y ou can normally invoke the BIOS setup menu by pressing a key or a combination of keys at the first boot up screen. Some of the common keys are DELETE, F1, F2, CTRL+AL T+S, CTRL+AL T+ESC.
6 Figure 3b: Windows 95 (or 95A) COM2 Disable Panel Pr oceed to the section titled “Installing the Modem.”.
7 F or Windo ws NT 4.0 Installation Remo ve all other modem drivers from your operating system. On the S tart menu, click Settings then click Control P anel. In Control P anel, double-click on the Mo - dems icon. S elect the modem you wish to remo ve and click Remove.
8 Hardw are Installation 1. T urn off the computer and all peripheral devices connected to it. 2. U nplug the computer power cord from the wall r eceptacle. 3. R emove the computer’ s cover . Refer to your computer owner ’ s manual for instructions.
9 5. F irmly , but gently , insert the modem into the available 16-bit expansion slot. Ensure that the card is seated properly before securing it with the screw remo ved in S tep 4, as shown in the following diagram: Figure 6: Installing The Modem 6. Put the chassis co ver back on the computer .
10 Connecting De vices T o The Modem Fig.7: Connecting Devices On the rear panel of your modem are input jacks to connect devices to the modem. As shown in the diagram, ther e are jacks for connection to a “ phone” and to a phone “line.” The connector labeled Line (T elco) is meant to be connected to a standard analog phone line.
11 Configur ing Windo ws 95 S tep 1 U pon startup, W indows 95 detects the modem and displays the Ne w Har dware F ound dialog box. Select “D river from disk pro vided by hardware manufacturer ” then click OK . Step 2 T ype your CD-R OM drive ’ s drive letter into the Copy manufactur er’ s files from box.
12 Step 4 After the installer has copied the .INF files to the hard disk, a New Har dwar e F ound dialog box should appear prompting for the “W ave Device for V oice M odem ”. Click OK . (See “Do This F irst ” for information on UNIMODEM.INF if this screen does not appear).
13 S tep 6 T o determine what COM por t and IR Q is assigned to the modem in Windows 95, click on the M odems icon in Control P anel and select the Diagnostic tab . Click on the COM P or t icon and then on the M ore Info button to view the modem proper ties.
14 Configur ing Windo ws 95 OEM SR2 S tep 1 U pon startup, W indows 95 detects the modem and launches the U pdate Device Driver Wizard dialog box. Insert the modem ’ s installation CD-R OM and click Next. Step 2 After Windows 95 has found the updated drivers for your modem, click Finish.
15 Step 3 If Windows asks for its own installation disc, click OK. Insert the requested CD-R OM, type the drive letter of your CD-R OM in the dialog box that appears next, and click OK . S tep 4 After the Wizar d has copied the .INF files to the hard disk, it should detect “ W ave Device for V oice Modem ” and prompt for its driver .
16 S tep 6 T o determine what COM por t and IR Q is assigned to the modem in Windows 95, click on the M odems icon in Control P anel and select the Diagnostics tab . Select your modem and then click on the Mor e Info button to view the modem proper ties.
17 S tep 7 R emember this COM port number . When you install your Data/F ax softwar e or internet browser program, you may need to set your modem port location to this same number .
18 Configur ing Windo ws 98 Step 1 After installing the modem hardware, turn on your computer . Windows will detect the modem and start the Add N ew Hardware W izard. Click N ext. Step 2 The Add N ew Har dware W izard will ask if you would like it to “ search for the best driver for your device (Recommended).
19 Step 3 The Wizard will ask wher e it should search for the drivers. Click “CD- R OM drive ” to select it. Make sure the installation CD-R OM is in the CD- R OM drive. Click N ext. Step 4 N ext the Wizard will identify the driver file and r eport its location on the CD-R OM drive.
20 Step 5 After copying the files to your hard drive, the wizard will report that it is finished installing the drivers for the modem. Click Finish. Step 6 Windo ws will now detect a “W ave Device for V oice M odem ” and star t the Add N ew Hardware Wizar d again to find the drivers for the voice capabilities of your modem.
21 Step 7 The Add N ew Hardware Wizar d will ask if you would like it to “ search for the best driver for your device (Recommended).” If this option is not alr eady selected, click it, then click N ext. Step 8 The Wizard will ask wher e it should search for the drivers.
22 Step 9 N ext the Wizard will identify the driver file and r eport its location on the CD-R OM drive. Click the N ext button to copy and instal the driver . S tep 10 Windows will copy and install the files, and then display the dialog box below , repor ting that the process has finished.
23 Step 11 Windows will finish loading. T o make sure your modem has been installed correctly , click Start on the taskbar . On the S tart menu, click Settings, then click Control P anel. In Contr ol P anel, double-click the Modems icon, then click the P roperties tab to bring it to the front.
24 Step 12 Check that the M ore Info dialog box that appears on your screen matches the illustration below . Make a note of the interrupt (also known as an IR Q) and the port number . These will be needed to configure y our communications software. Y our modem is now installed and configured for use with Windows 98.
25 Configur ing Windo ws NT 4.0 Before installing the modem, make sure you have installed the P nP ISA Enabler and the latest Service Pack upgrade to Windows NT 4.0. See the section titled “Do This F irst” for details. Step1 Install the modem hardware and turn on your computer .
26 Step 4 A panel for selecting the device to be installed should appear . H ighlight the “V .90 Windows M odem (LHT)” selection and click OK . Step 5 If you see the following dialog box, you will need to set the configuration manually .
27 S tep 6 Select the Resource Settings which do not cause any conflicts with other devices. Step 7 R estart your computer . Step 8 Click on the Modems icon in the Control P anel .
28 Step 10 At the Remote Access Setup dialog box, click on Add. Select the Remote Access Setup device you wish to add and Click OK. Step 11 Click Continue to finish the installation. Step 12 After Windows NT has completed the binding process, allow Windows NT to shut down and restart the computer .
29 Installing and Configuring Comm unications Software If your modem came with a communications software package, it is strongly recom- mended that you use this software for your modem. I t ’ s default installation param- eters have been specially configured to work with this modem.
30 call is detected. The modem converts the digital information contained in the .wav file into an audio signal which is then sent over the phone line. The person calling hears your outgoing message and responds with an incoming message. The sequence of recording an incoming message is the reverse of an outgoing mes- sage.
31 Windo ws 95 and Windo ws 98 Step 1: Chec k System Resour ces. In Control P anel double-click the System icon. Click the Device M anager tab . In the list of devices, double-click the Modems icon to show what modems are in- stalled. If there is no M odems icon, your modem did not install.
32 Figure 8: More Inf o P anel If you receive an error message or the panel is blank, go to the section of this manual “Does N ot Install.” Step 4: Does Not Install The most likely reason for a non-installation in Windows 95 or 98 is a lack of IR Q resources.
33 Play ”, or if y ou have “Plug N Play ” settings, set them to “ on.” Next, from the infor- mation you noted in S tep 2, find the interrupt selection for the IR Q your modem is using (some BIOS don ’ t allow individual selection of interrupts to ISA, Plug-N-Play , or PCI).
34 Note to users of Windo ws 95 and 98 If you are using W indows 95 or 98, ther e are two additional files which may be generateed when installing a piece of hardware from an OEM. The file is called oem#.inf. The number (#) used is generated b y Windows 95 each time an additional piece of hardware is installed.
35 After Windows finds the other file, delete it as befor e. Restart your system and follow the installation procedures in the section of this manual titled “Installing the M o- dem.” Note to users of Windo ws NT W indows NT 4.0 installation problems are often due to inadequate preparation.
36 Nothing Appears On The Screen When I T ype Issue the command A TE1 to the modem to enable command echo. This will let you see what you type. Cannot Connect at 56K N ote: Current FCC r egulations limit your maximum connection rate to 53Kbits/s. The number you are calling may not support V .
37 Y our phone line may not suppor t or may only intermittently support a 56K connec- tion. Ther e are many conditions that must be met before a 56K connection can be established. The telephone company must hav e you connected to the (P ublic S witched T elephone Network) in a particular way .
38 Appendix B: Comm unications Regulations FCC Regulations The following statements are pro vided in accordance with the F ederal Communica- tions Commission (FCC) regulations. Please read these statements carefully before installing your modem. FCC P ar t 68 Requirements This equipment complies with P art 68 of the FCC Rules.
39 Declar ation of Conf or mity This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to P art 15 of the FCC Rules. These limits are designed to provide r easonable protection against harmful interference in a residential installa- tion.
40 Canadian Depar tment Of Comm unications (CDOC) Requirements for End U sers: N otice: The Canadian Department of Communications label identifies cer tified equip- ment. This cer tification means the equipment meets certain telecommunications network requirements.
Een belangrijk punt na aankoop van elk apparaat Actiontec electronic 56K ISA Lite (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Actiontec electronic 56K ISA Lite heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Actiontec electronic 56K ISA Lite vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Actiontec electronic 56K ISA Lite leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Actiontec electronic 56K ISA Lite krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Actiontec electronic 56K ISA Lite bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Actiontec electronic 56K ISA Lite kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Actiontec electronic 56K ISA Lite . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
