Gebruiksaanwijzing /service van het product KLT-12G van de fabrikant Blodgett
Ga naar pagina of 23
1 IMPORTANT NOTES FOR INSTALLATION AND OPERATION KLT-12G GAS FIRED FLOOR MODEL TILTING KETTLE INSTALLATION – OPERATION – MAINTENANCE BLODGETT OVEN COMPANY www.
2 It is recommended that this manual be read thoroughly and that all instructions be followed carefully. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
3 TABLE OF CONTENTS DESCRIPTION PAGE 1.0 IMPORTANT NOTES FOR INSTALLATION AND OPERATI ON ........................... 2 2.0 SERVICE CONNECTIONS ................................................................................... 4 3.0 INTRODUCTION .....
4 2.0 SERVICE CONNECTIONS 3 [76] 4.75 [121] 23.75 [603] 25.388 [645] 17.25 [438] 5.5 [140 ] 1 1.25 [2 86] 15 [381] 7.75 [197] MIN. 6 [152] 12.50 [317] POUR P A TH 6 [152] 23.88 [607] 32.88 [835] 55.75 [1416] 30 [762] Ø16.75 [425] I.D. Ø20 [508] 15.88 [403] FLANGED FOOT DETAIL 4 7/16" [1 1mm] HOLES ON 3 [76] B.
5 3.0 INTRODUCTION DESCRIPTION Model KLT-12G (12 gallon capacity) gas fired, self -contained, tilting kettle. The kettle has a jacket of double-wall construction forming a sealed reservoir around the lower two-thirds of the kettle. The reservoir is charged with distilled water.
6 4.0 INSTALLATION INSTRUCTIONS GENERAL Gas installation to conform to local codes or in absence of local codes to the National Fuel Gas Code - ANSI Z223.1 - latest edition. In Canada, installation to be according to CAN/CGA- B149.1 (NAT) or CAN/CGA-B149.
7 GAS CONNECTION 1. The Serial and Rating Plate on the unit indicates the type of gas your unit is equipped to burn. DO NOT connect to any other gas type. 2. A 3/4" NPT line is provided at rear for the connection. The unit is equipped with an internal pressure regulator which is set at 4" W.
8 INSTALLATION 1. Uncrate carefully. Report any hidden freight damage to the freight company immediately. 2. Ideally an exhaust system should be direct ly above the appliance to exhaust combustion gases generated by the unit. 3. The appliance is intended for use on noncombustible floors.
9 5.0 OPERATING INSTRUCTIONS FRONT PANEL CONTROLS: Power Switch This switch turns the main power to the unit on and off. It must be turned on to heat the kettle. It should be turned off when the kettle will not be in use for long periods. Thermostat Selects the desired internal kettle operating tem perature.
10 TILTING INSTRUCTIONS Your kettle has the standard “Clean Lock” feature and may not be tilted without disengaging the tilt knob located on the console at the top left. This feature locks the kettle in the upright position and also allows the operator to lock the kettle at 105 degrees for ease of cleaning.
11 6.0 PERIODIC MAINTENANCE All units are adjusted at the factory. In order to avoid problems in operation, check type of gas an d manifold pressure at initial installation and compare it with information on the rating plate. CLEANING The gas fired tilting kettle should be cleaned after each use.
12 GENERAL SERVICE In order to avoid problems, check that the unit has been connected to the gas supply type and voltage for which it was supplied. This can be done by examining the rating plate that lists the gas type and voltage for which the unit was manufactured.
13 counterclockwise. Use the centre of the black ring as an indicator. 6. If relief valve opens, reduce setting on pressure switch, cool kettle completely by filling with cold water and repeat this procedure.
14 7.0 TROUBLESHOOTING Unit does not come on: 1. Power switch and/or thermostat is “OFF”. 2. Unit is not plugged in. 3. Main power supply is off. 4. Tilt micro switch out of alignment or faulty. Unit is on electrically but does not heat: 1. Gas supply to the unit is “OFF”.
15 APPENDIX ‘A’ MATERIAL SAFETY DATA SHEET PREPARATION INFORMATION: Prepared for use in Canada by: E H & S Product Regulatory Management Department DOW CHEMICAL CANADA INC.
16 S HAZARDS IDENTIFICATION EMERGENCY OVERVIEW POTENTIAL HEALTH EFFECTS (See Section 11 for toxicological data.) EYE: May cause slight transient (temporary) eye i rritation. Corneal injury is unlikely. Mists may cause eye irritation. SKIN CONTACT: Prolonged contact is essentially nonirritating to skin.
17 4. FIRST AID EYES: Flush eyes with plenty of water. SKIN: Wash off in flowing water or shower. INGESTION: No adverse effects anticipat ed by this route of exposure incidental to proper industrial handling. INHALATION: Remove to fresh air if effects occur.
18 possibly resulting in spontaneous combustion. Container may rupture from gas generation in a fire situation. EXTINGUISHING MEDIA : Water fog or fine spray, carbon dioxide, dry chemical, foam. Alcohol resistant foams (ATC type) are preferred if available.
19 S EXPOSURE CONTROLS/PERSONAL PROTECTION ENGINEERING CONTROLS: Provide general and/or local exhaust ventilation to control airborne levels below the exposure guidelines.
20 HAZARDOUS DECOMPOSITION PRODUCTS: Hazardous decomposition products depend upon temperature, air supply and the presence of other materials. HAZARDOUS POLYMERIZATION: Will not occur. 11. TOXICOLOGICAL INFORMATION (See Section 3 for Potential Health Effects.
21 local laws and regulations. Regulations may vary in different locations. Waste characterizations and compliance with applicable laws are the re sponsibility solely of the waste generator. THE DOW CHEMICAL COMPANY HAS NO CONTROL OVER THE MANAGEMENT PRACTICES OR MANUFACT URING PROCESSES OF PARTIES HANDLI NG OR USING THIS MATERIAL.
22 U.S. REGULATIONS SARA 313 INFORMATION: To the best of our knowledge, this product contains no chemical subject to SARA Title III Section 313 supplier notification requirements.
23 CANADIAN REGULATIONS WHMIS INFORMATION: The Canadian Workplace Hazardous Materials Information System (WHMIS) Classification for this product is: This product is not a “Controlled Product” under WHMIS.
Een belangrijk punt na aankoop van elk apparaat Blodgett KLT-12G (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Blodgett KLT-12G heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Blodgett KLT-12G vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Blodgett KLT-12G leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Blodgett KLT-12G krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Blodgett KLT-12G bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Blodgett KLT-12G kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Blodgett KLT-12G . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
