Gebruiksaanwijzing /service van het product HMV9305 van de fabrikant Bosch Appliances
Ga naar pagina of 20
Household Appliances Over -the-Range Microwave Installation Instructions For Models: HMV9302, HMV9305, HMV9306, HMV9307 PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING IMPORT ANT : Save these instructions for the local electrical inspector’ s use.
2 YOUR SAFETY FIRST BEFORE YOU ST ART • Proper installation is the installer's responsibility! – Read the entire manual before you begin. The Model number label is located on the oven front. See Figure 1. Mounting plate is located on back side of microwave oven.
3 • THIS APPLIANCE MUST BE GROUNDED!.
4 • MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT. – Mount the oven against a flat, vertical wall, so it is supported by the wall. The wall should be constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.
5 THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN: P AR TS, TOOLS, MA TERIALS Damper/duct connector (for roof vented or wall vented installation) Not Actual Size Four 1/4" x 2" lag screws - A.
6 YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION: Carton or other heavy material for covering the counter top. • If you have brick or masonry walls, you will need special hardware and tools. • The ductwork you need for the installation is not included.
7 A VOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED! 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 4 Detail. 2. You will cut the power-supply-cord hole (shown in Figure 4 Detail) later when you prepare the wall and upper cabinet in Step 4.
8 THIS OVEN MUST BE PROPERLY VENTED! You may vent your oven in one of three ways: Roof-venting If your oven is located on an outside wall near the roof, as in Figures 5 (3 1 / 4 " x 10" duct) and 8 (6" round duct.
9 STEP 2: PREP ARE THE VENTING SYSYTEM ST ANDARD FITTINGS DUCT LENGTH The total length of the duct system, including straight duct, elbows, transitions, wall or roof caps must not exceed the equivalent of 140 feet. For best performance, do not use more than three 90 degree elbows.
10 Your microwave oven is shipped with the blower assembled for roof venting. You need to adjust the blower if you want wall-venting or room-vented (recirculating) installation.
11 W ALL-VENTED INST ALLA TION: 1. Remove one blower unit mounting screw and one blower plate screw. Remove the blower plate from cabinet. See Figure 13. 2. Carefully lift the blower unit out of the microwave oven. 3. Use side cutters or tin snips to cut and remove knockouts “B” from Back plate.
12 STEP 3: PREP ARE THE VENTING BLOWER ROOM-VENTED (Recirculating) INST ALLA TION: 1. Remove one blower unit mounting screw and one blower plate screw. Remove the blower plate from cabinet. See Figure 19. 2. Carefully lift the blower unit out of the microwave oven.
13 MEASURE AND T ACK / T APE UP THE TEMPLA TES 1. Using a plumb line and (metal) measuring tape, find and mark the vertical center line on the back wall, as in Figure 22. 2. Find and mark one or two points where the studs are on the wall (Studs are normally 16 inches apart) and then measure and mark the stud locations.
14 DRILLING THE HOLES IN THE W ALL AND UPPER CABINET : BE VER Y CAREFUL WHEN DRILLING HOLES INTO THE W ALL. Electrical wires could be concealed behind the wall covering and if the drill hits them you could get an electric shock. 1. Find the points on the mounting plate labeled A, B, C , and D .
15 STEP 5: INST ALL THE MOUNTING PLA TE TO THE W ALL 1. Draw a vertical line on the wall at the center of the 30 ″ wide space. Use the mounting plate as the template for the rear wall. Place the mounting plate on the wall, making sure that the tabs are against the bottom of the cabinet.
16 STEP 5: INST ALL THE MOUNTING PLA TE TO THE W ALL TO PREP ARE THE REAR W ALL CUTOUT OPENING AND EXHAUST ADAPTOR/MOUNTING PLA TE FOR W ALL-VENTED: 1. Place the mounting plate against the rear wall as described in step 5 item 1 (page 15). 2. Using a pencil, put dots through slots F and G, and through holes H and I.
17 STEP 6: A TT ACH THE OVEN TO THE W ALL You will need two people to lift this microwave. Failure to use more than one person could result in personal injury . 1. Carefully lift microwave oven and hang it on support tabs (See Figure 26 on the page 15) at the bottom of the mounting plate.
18 STEP 6: A TT ACH THE OVEN TO THE W ALL 5. Roof vented installation: See Figure 32 Install ductwork through the vent opening in the upper cabinet. Complete the venting system through the roof according to the method needed. See “ PREPARE THE VENTING SYSTEM, ” step 2 on the page 8.
Installation Notes.
Printed in Korea P/No.: 3828W5U0310.
Een belangrijk punt na aankoop van elk apparaat Bosch Appliances HMV9305 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Bosch Appliances HMV9305 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Bosch Appliances HMV9305 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Bosch Appliances HMV9305 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Bosch Appliances HMV9305 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Bosch Appliances HMV9305 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Bosch Appliances HMV9305 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Bosch Appliances HMV9305 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
