Gebruiksaanwijzing /service van het product ICP-CC404 van de fabrikant Bosch Appliances
Ga naar pagina of 98
EN Installation Guide ICP-CC404 Control Panel ICP-CC404.
ICP-CC404 | Installation Guide | Copyright Notice 2 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 Copyright Notice Unless other wise indicated, th is publication is the copyright of Bosch Security Systems, Inc. (“ Bosch ”). All ri ghts are r eserve d.
ICP-CC404 | Installation Guide | Contents Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 3 Contents 1.0 Introduc tion ....... .......... .......... .......... ............. ....7 1.1 Features ... .......... ........... .......... .......... ..
ICP-CC404 | Installation Guide | Contents 4 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 6.3.5 Bell Test................ ............ ............ ........... ..........37 6.3.6 Strobe Test ................... ............ .......... .........
ICP-CC404 | Installation Guide | Contents Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 5 16.6 One-Shot Polarities ........ .......... .......... ........... ...70 17.0 System Event Timers............ ............. .......... ..70 17.1 Programming Entry /Exit Timers.
ICP-CC404 | Installation Guide | Contents 6 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 Tables Table 1: Zone D efaults.... .......... ............ ........... ..........8 Table 2: Zone T ypes ............... .......... ........... .......... .
ICP-CC404 | Installation Guide | 1.0 Introduction Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 7 1 .0 Int roduct ion Congratulations on selecting the ICP-CC404 Control Panel for your installation .
ICP-CC404 | Installation Guide | 1.0 Introduction 8 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 When programming th e telephone numbers for Receiver 1 and Receiver 2, you m ust program a 0 as a 10. Program ming a 0 in the telep hone number indicates the end of the dialing sequence.
ICP-CC404 | Installation Guide | 2.0 Programming Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 9 2.0 Programming The control p anel progra mming optio ns are stored in a non-volatile EP ROM. This memory holds all configuration a nd user-specifi c data even after a total power loss.
ICP-CC404 | Installation Guide | 2.0 Programming 10 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 2.2 Prog ramming with the Programming Key The CC891 Programming Key allows you to store or copy programming information from your control panel.
ICP-CC404 | Installation Guide | 2.0 Programming Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 11 2.4.1 Command 9 58 – Enable/Di sable Zone Status Mode This function enables an d disables Zone Status Display Mode w hen using the hand-held programmer.
ICP-CC404 | Installation Guide | 2.0 Programming 12 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 2.4.3 Command 9 60 – Exit from the Insta ller's Programming M ode This command exits from th e Installer’s Programming Mo de. You can ex it from the Installer’s Programm ing Mo de from any location.
ICP-CC404 | Installation Guide | 2.0 Programming Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 13 2.4.7 Com mand 964 – Erase the P rogramm ing Key This command erases all data fro m the programming key. You can onl y use the CC891 Programmi ng Key with the ICP-CC404 Control Panel.
ICP-CC404 | Installation Guide | 2.0 Programming 14 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 Table 6: Command 965 Defaults Location Description Default Value Setting 032 Handshake To ne fo.
ICP-CC404 | Installation Guide | 2.0 Programming Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 15 2.5 Disable Factory Defaul ts Program the Disable Factor y Defaults feature in Location 900 .
ICP-CC404 | Installation Guide | 3. 0 Codep ad Indicators 16 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 3.0 Codepad Indic at ors 3.1 ICP-CP508 W Eight Zo ne LED Codepad Figure 1: ICP-CP508W Eight Zone LED Codepad The codepad is the co mmunications in terface between you an d the alarm system.
ICP-CC404 | Installation Guide | 3.0 Codepad Indicators Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 17 Table 12: FAULT Indicator Indicator Definition On A system fault m ust be corrected Of.
ICP-CC404 | Installation Guide | 4.0 System Operations 18 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 Zone Isola ting Mode Flashing This indicator (the person) flashes once every 3 sec when you attempt to isolate zones or prog ram zone s to automatically isolate for STAY Mode 2.
ICP-CC404 | Installation Guide | 4.0 System Operations Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 19 Two beeps so und and the AWAY ind icator is extinguished.
ICP-CC404 | Installation Guide | 4.0 System Operations 20 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 4.5 Arming th e System in STAY Mo de 2 Use STAY Mode 2 to arm the perimeter and unused areas of the pr emises to detect an intruder, while at the same time being able to move freely within an automatically isolated are a.
ICP-CC404 | Installation Guide | 4.0 System Operations Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 21 4.7 Codepad Dure ss Alarm Figure 3: ICP-CP508W LED Code pad Showing Audible Al arm Buttons A codepad D uress Alarm is us ed as a silent ho ldup alarm when 9 is added to the end of a va lid User Code used to dis arm the system.
ICP-CC404 | Installation Guide | 4.0 System Operations 22 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 2. Enter the number of t he zone to isolate and press [STAY]. The indicator for th e zone flashes. 24-Hour zones are automati cally isolated as soon as you press [STAY].
ICP-CC404 | Installation Guide | 4.0 System Operations Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 23 2 – Date and Time The date and time fault occurs ever y time power is removed from the control pa nel.
ICP-CC404 | Installation Guide | 5.0 Remote Radio Transmitter Ope rations 24 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 AC MAINS Failure An AC MAINS supply failur e automatically flash es the MAINS indicator.
ICP-CC404 | Installation Guide | 5 .0 Remote Radio Transmitter Operation s Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 25 To add or change a re mo te radio User Code : 1. Enter the Master Code and press [1][AWAY]. Three beeps soun d and the STAY and AWAY indicators flash.
ICP-CC404 | Installation Guide | 5.0 Remote Radio Transmitter Ope rations 26 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 If horn spea ker indication beeps are enabled, one two-tone beep sounds from the horn speaker. If strobe indications ar e enabled, the strobe flashes fo r 6 sec to indicate th e system is armed.
ICP-CC404 | Installation Guide | 6.0 System Functions Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 27 If horn spea ker indication beeps are enabled, one beep sounds from the ho rn speaker. If strobe indications are enabled, the strobe flashes for 3 sec to indicate the syst em is disarmed.
ICP-CC404 | Installation Guide | 6.0 System Functions 28 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 To set the first Test Report: 1. Enter the Installer Code and press [1][A WAY]. Three beeps soun d and the STAY and AWAY indicators flash. 2.
ICP-CC404 | Installation Guide | 6.0 System Functions Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 29 When arming the system in AWAY Mode, the control panel au tomatically dials the telecommunication exchange to redirect all calls to your mobile pho ne, pocket pager, or answering service.
ICP-CC404 | Installation Guide | 6.0 System Functions 30 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 To disable the Telco disarming sequence: Enter the Installer Code and press [3][AWAY][2] [AWAY][STAY][4][AWAY]. To program the Te lco arming sequ ence – easy call forward (immediate on): 1.
ICP-CC404 | Installation Guide | 6.0 System Functions Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 31 To enter Sa tellite Siren Service Mode : Enter the Installer Code and press [5][AWAY].
ICP-CC404 | Installation Guide | 6.0 System Functions 32 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 The default Master Code is 2580 and is User Code 1. You can program multiple Master Codes. Refer to Sectio n 13.3 User Code Priority on page 52 fo r more information.
ICP-CC404 | Installation Guide | 6.0 System Functions Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 33 3. Press any of the [TRANSMIT] buttons on the hand-held transmitter. Two beeps soun d and the STAY and AWAY indicators turn off. 4. Repeat this procedu re to change other re mote radio User Codes.
ICP-CC404 | Installation Guide | 6.0 System Functions 34 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 6.2.4 Change Te lco Arming or Disarming Sequence Program the call forward se quence to automatically operate when you arm the system in AW AY Mode.
ICP-CC404 | Installation Guide | 6.0 System Functions Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 35 If there is no Telco disarming sequence programmed , an additional two beeps sound after entering this mo de. These two beeps n ormally sound after the last di git of the sequence is shown.
ICP-CC404 | Installation Guide | 6.0 System Functions 36 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 You can disable all zones s elected to automatically isolate for STAY Mode 2 at any time. To disable STAY Mode 2 zones: Enter your Master Code and press [4][AWAY] [AWAY].
ICP-CC404 | Installation Guide | 6.0 System Functions Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 37 To enter Event Memory Recall Mode: Enter your Master Code and press [8][AWAY]. Three beeps sou nd. The events are played back by the codepad in dicators in re verse chronological order.
ICP-CC404 | Installation Guide | 7.0 Remote Arming by Telephone 38 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 6.3.7 Turning Day Alarm On and Off Pressing and holding [4] turn s Day Alarm on or off.
ICP-CC404 | Installation Guide | 8.0 Alarm Link Software Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 39 If the control pane l does not answer the call, the system might be armed alre ady, remote functions are not enabled, or the Ring Coun t is set to 0.
ICP-CC404 | Installation Guide | 9.0 Dome stic Dialing 40 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 To program the control pane l for remote connection with callback verification: 1. Program the Call Back Telephon e Number in Locations 159 to 174 (refer to Section 11.
ICP-CC404 | Installation Guide | 9.0 Domestic Dialing Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 41 If a busy tone is not de tected, the control panel assumes that the telephon e was answered and sends its transmiss ion. The transm iss ion sequence consists of an identification beep, fo llowed by a siren to ne and a long pause.
ICP-CC404 | Installation Guide | 10.0 Dialer Reporting Formats 42 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 1 0 .0 Dialer Reporting Formats 10.1 Transmission Formats The ICP-CC404 Control Panel pr ovides a number of transmission formats for its dialing and communication fea tures.
ICP-CC404 | Installation Guide | 10.0 Dialer Reporting Formats Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 43 Table 33: Poi nt ID Codes Poin t ID Event Description Event Code Explanation Section Zones 1 to 8 Burgla ry Zone 130 Burglary 1 4.
ICP-CC404 | Installation Guide | 10.0 Dialer Reporting Formats 44 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 Table 36: 4+2 Express Transmissi on Code Descriptions Code Description SSSS Subsc.
ICP-CC404 | Installation Guide | 10.0 Dialer Reporting Formats Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 45 Figure 6: Basic Pager Display 1 – Subsc riber ID number 2 – Zon e status 3 .
ICP-CC404 | Installation Guide | 11.0 Dialer Information 46 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 System Sta tus The system status informatio n is sh own by four digits, which are defined in Figure 6 on page 45. The first digit indicates whether the system is armed or disarmed.
ICP-CC404 | Installation Guide | 11.0 Dialer Informatio n Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 47 When Receivers 1 or 2 is set up for domestic reporting, telephone numbers programmed into these locations are ignored. Refer to Section 6.
ICP-CC404 | Installation Guide | 11.0 Dialer Information 48 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 When using Domestic Dialing Format, the nu mber of identification beeps is determined by the value programmed in Location 039 (Receiver 1) and Location 079 (Receiver 2) .
ICP-CC404 | Installation Guide | 11.0 Dialer Informatio n Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 49 To turn call forward (no answer) off, enter: [# 6 1 #] Example To disable c all forward (n o answer) after disarming the system from AWAY Mode, program: 12 6 1 12 0 0 0 0 0 0 0 0 0 0 0 0 11.
ICP-CC404 | Installation Guide | 12.0 Dialer Options 50 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 The options are: 1 – Display FA ULT Indicator When the Tel ephone Line Fails When this op.
ICP-CC404 | Installation Guide | 13.0 Access Code Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 51 Open/Close Report s must be enabled in Locations 333 and 334 (refer to Section 15.
ICP-CC404 | Installation Guide | 13.0 Access Code 52 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 User Codes are four digits long. The fifth position specifies the priority leve l for the code. Each User Code has its own priority le vel. Mo re than one User Code can have the same priority level.
ICP-CC404 | Installation Guide | 14.0 Zone Information Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 53 1 4.0 Zone Informat ion 14.1 Day Alarm Information Program the desired Day Alarm Zones in Location 265 .
ICP-CC404 | Installation Guide | 14.0 Zone Information 54 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 If you select split EOL resistors, the control panel looks for four Burglary Zones (1 to 4) with 3.3 k Ω EOL resistors and four 24-Hour Zones (5 to 8) consis ting of 6.
ICP-CC404 | Installation Guide | 14.0 Zone Information Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 55 The Zone Report Cod e determines whether the control panel sends Alar m Reports for the zone. Refer to Section 14.3.7 Zone Report Code on page 59 for more information.
ICP-CC404 | Installation Guide | 14.0 Zone Information 56 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 8 – 24-Hour Holdup Zone A 24-Hour Holdup Zone (Contact ID Event Code 122) is always ready to ac tivate the dialer, horn speaker, bell, and s trobe, re gardless of whether the system is armed or disarmed .
ICP-CC404 | Installation Guide | 14.0 Zone Information Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 57 For zone pulse count time , Options 0 to 7 have a zone loop response time of 20 ms and Options 8 to 15 have a zone loop response time of 150 ms.
ICP-CC404 | Installation Guide | 14.0 Zone Information 58 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 2 – Latching Disarm from AWAY Mode, STAY Mode 1, or STAY Mod e 2 The system is disarmed from AWAY Mode, STAY Mode 1, or STAY Mode 2 when using the latching keyswitch input.
ICP-CC404 | Installation Guide | 14.0 Zone Information Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 59 If you do not want the sy stem to send Zone Bypass Reports, program Locations 325 and 326 to 0 (refer to Section 15.1 Zone Status – Bypass Reports on page 60).
ICP-CC404 | Installation Guide | 15.0 System Reporting Information 60 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 Example All eight zones ar e programmed for lockout dialer with a Swinger Sh utdown Count of 6. If Zone 1 activates an alarm, the Swinger Shutdown Count decreased to 5 when the control panel calls.
ICP-CC404 | Installation Guide | 15.0 System Reporting Information Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 61 Location 332 ( Section 15.5 Zone Status Reporting Options on page 61) is ignored wh en pro gramming the Alarm Restore code and is global for all zo nes.
ICP-CC404 | Installation Guide | 15.0 System Reporting Information 62 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 A Fire Alarm Report (Contact ID Event Code 110) is sent to the base st ation receiver when a user pres ses [4] and [6] at the same time .
ICP-CC404 | Installation Guide | 15.0 System Reporting Information Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 63 A Battery Test Failure Report (Contact ID Event Code 309) is sent to the base station receiver when the system’s battery voltag e falls below 11.
ICP-CC404 | Installation Guide | 16.0 Programmable Ou tputs 64 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 Table 50: Test Reporting Time Parameters Location Parameter Default 360 Hour of day .
ICP-CC404 | Installation Guide | 16.0 Programmable Outputs Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 65 Example 3,0 Communications Failure This event operat es after the dialer makes a ll possible attempts to reach the base station receiver.
ICP-CC404 | Installation Guide | 16.0 Programmable Ou tputs 66 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 The output also operates du ring the Entry Guard Timer for STAY Mode time. If a zone programmed fo r day alarm is activated when the system is disarmed, t he output res ets when the zone is res ealed.
ICP-CC404 | Installation Guide | 16.0 Programmable Outputs Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 67 1,12 Codepad Ta mper – Access De nied This output operates when the wrong code is entered more times than allowed. The number o f incorrect attempts allowed is programmed in Location 356 (refer to Section 15.
ICP-CC404 | Installation Guide | 16.0 Programmable Ou tputs 68 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 2,13 Ra dio Control Output 1 – Not in AWAY Mode This output operates when the [DOOR] button on the four-channel hand-held tran smitter is activated.
ICP-CC404 | Installation Guide | 16.0 Programmable Outputs Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 69 Table 54: Event Type Polarities Option Description 0 Output not used 1 Normally ope.
ICP-CC404 | Installation Guide | 17.0 System Event Timers 70 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 13 – Normall y Low, One-Shot Open with Alarm This one-shot p olarity is normally 0 V and switches to an open circuit wh en the event oc curs.
ICP-CC404 | Insta llation Guide | 17.0 System Event Timers Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 71 You can program Entry Ti mer 1 from 0 to 255 sec in increments of 1 sec. Entry Timer 1 is th e delay time used by the Delay-1 Zones. Refer to Section 14.
ICP-CC404 | Installation Guide | 17.0 System Event Timers 72 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 The Siren So und Rate vari es the frequency of the siren tone slowest (0) and to fastest (15). The Siren Sound Rate does n o t change the frequency of the fire alarm tone.
ICP-CC404 | Installation Guide | 18.0 System and Consumer Options Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 73 Table 61: System Date Parameters Location Parameter Default 905 Day of the m.
ICP-CC404 | Installation Guide | 18.0 System and Consumer Options 74 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 If you want to disable th e reporting of a Codepad Fire Alarm, program Locations 339 and 340 as 0 (refer to Section 15.10 Codepad Fire Report on page 61).
ICP-CC404 | Installation Guide | 18.0 System and Consumer Options Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 75 4 – Internal Crystal Keeps Time If this option is selected , the con trol panel uses the internal crystal (XTAL) to track time.
ICP-CC404 | Installation Guide | 19.0 Optional Equipment 76 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 4 – Alarms Ac tivate Sirens a nd Strobe Outputs in STAY Modes 1 an d 2 Select this optio n if audible alarms a re required when the system is armed in STAY Mode 1 or 2.
ICP-CC404 | Installation Guide | 19.0 Optional Equipment Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 77 19.7 CP5 Eight Zone LCD Codepad (CP508LW) This codepad operates with the ran ge of contro l panels. This codepad h as a fixed ico n display and provides indications fo r up to eight zones.
ICP-CC404 | Installation Guide | 20.0 Terminals and Descriptions 78 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 20.0 T erminals and Descript ions 20.1 Terminal Descriptions Table 64: Terminal Descript ions Terminal Descri ption EARTH Connect this terminal to the green wire on the TF008 Plug Pack that is internally connected to mains earth.
ICP-CC404 | Installation Guide | 20.0 Terminals and Descriptions Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 79 20.2 Glossary Of Te rms Table 65: Glossary Term Description 24-hour zone A monitored input where tamper switche s and emergency switches can be c onnected.
ICP-CC404 | Installation Guide | 20.0 Terminals and Descriptions 80 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 Table 65: (continued) Term Description master code A numeric code used for arming and disarm ing the system, and for allowing access to all functions available through the codepad.
ICP-CC404 | Installation Guide | 20.0 Terminals and Descriptions Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 81 20.3 Diagrams Figure 11: ICP-CC404 Wiring Diagram 1 – 605 plug 2 – 6 (Red.
ICP-CC404 | Installation Guide | 20.0 Terminals and Descriptions 82 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 Figure 12: ICP-CC404 Component Overla y 1 – Socket for telecom lead connect 2.
ICP-CC404 | Installation Guide | 20.0 Terminals and Descriptions Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 83 Figure 13: Telecom Conne ction Diagram for Australia 1 2 3 9 7 4 5 6 10 2 3 9.
ICP-CC404 | Installation Guide | 21.0 Specifications 84 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 2 1 .0 Specificat ions Table 66: Specifications Temperature Range 0 o C to + 45 o C (+32 o F to +113 o F) Humidity 10% to 95% Power Source TF008 Plug Pack – 240 VAC/18 VAC @ 1.
ICP-CC404 | Installation Guide | 22.0 Programming Sheets Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 85 22.0 Programm ing Sheet s Location Function Options/Notes Default/ Programming Entry .
ICP-CC404 | Installation Guide | 22.0 Programming Sheets 86 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 Location Function Options/Notes Default/ Programming Entry 8 175 Ring Count Refer to pa.
ICP-CC404 | Installation Guide | 22.0 Programming Sheets Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 87 Location Function Optio ns/Notes Default/ Programming Entry 185 to 264 User Codes Ref.
ICP-CC404 | Installation Guide | 22.0 Programming Sheets 88 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 Location Function Options/Notes Default/ Programming Entry 267 to 322 Zone Definitions .
ICP-CC404 | Installation Guide | 22.0 Programming Sheets Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 89 Location Function Options/Notes Default/ Programming Entry 3 323 Swinger Shutdown Cou.
ICP-CC404 | Installation Guide | 22.0 Programming Sheets 90 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 Location Function Optio ns/Notes Default/ Programming Entry 10 7 350 to 351 System Stat.
ICP-CC404 | Installation Guide | 22.0 Programming Sheets Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 91 Location Function Options/Notes Default/ Programming Entry The fifth and sixth locat ions of the output definit ion provide the time base multiplier.
ICP-CC404 | Installation Guide | 22.0 Programming Sheets 92 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 Location Function Options/Notes Default/ Programming Entry 0 425 System Options 2 Refer.
ICP-CC404 | Installation Guide | Contents Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 93 22. 1 Country Codes The PSTN provides a programmable line interface to meet internat ional telephone line r equirements. This program meets various co untry PTT standards.
ICP-CC404 | Installation Guide | Contents 94 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 Country Code Country Code Country Code Country Code Country Code New Zealand 3 6 Bahrain 6 3 El Salvad.
ICP-CC404 | Installation Guide | Index Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 95 Index 2-Channel Hand Held Tr ansmitter Ope rations Arming In AWAY Mode .................................. ............ 25 Arming In STAY Mode 1 ..........
ICP-CC404 | Installation Guide | Index 96 Bosch Security Systems, Inc. | 12/08 | F01U089401-02 Handover ....................... .......................... ........................... . 54 Hold Down Function Arm In STAY Mode 1.................. .......
ICP-CC404 | Installation Guide | Index Bosch Security Syst ems, Inc. | 12/ 08 | F01U089401-02 97 Test ....................... ................................ ........................... . 11 PS100 Power Supply Module ........... .....................
© 2008 Bosch Security Systems, Inc. F01U089401-02 Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, NY 14450-9199 U SA www.boschsecurity.com.
Een belangrijk punt na aankoop van elk apparaat Bosch Appliances ICP-CC404 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Bosch Appliances ICP-CC404 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Bosch Appliances ICP-CC404 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Bosch Appliances ICP-CC404 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Bosch Appliances ICP-CC404 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Bosch Appliances ICP-CC404 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Bosch Appliances ICP-CC404 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Bosch Appliances ICP-CC404 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.