Gebruiksaanwijzing /service van het product Network Unit van de fabrikant ADC
Ga naar pagina of 36
Ethernet Network Interface Unit (ENIU) User Manual 20383 - A1 E N I - E G X X E G X X 1 B Document Number: AIWN-UM-7001-01 Product Catalog: ENI-EGXXEGXX1B CLEI: IPUIA Y5F~~.
R EVISION H ISTORY The Revision Histo ry provides a summary of any changes in this manual. Please make sure yo u are using the latest revision of this manual. August 7, 2006 This manual is available online at ADC’ s website ( www .adc.com/doc umentatio nlibrary/) or yo u can order copies of the manual by contacting you r sales represent a tive.
T able of Content s AIWN-UM-7001-01 iii Chapter 1: Overview ......... ................................. ............................................................. 1- 1 Product Description ............................................................
T able of Content s August 7, 2006 iv AIWN-UM-7001-01.
List of Figures AIWN-UM-7001-01 v Figure 1-1. ENIU with SFPs ........... ............................................... ...................................... 1-1 Figure 1-2. ENIU Front View .......... ............................................... .
List of Figures August 7, 2006 vi AIWN-UM-7001-01.
List of T ables AIWN-UM-7001-01 vii T able 1-1. ENIU LED Indicators and C ontrols ........... ................................ ........................... 1-2 T able 2-1. 10/100 Mbps Ethernet RJ-45 Connector ......... .................................
List of T ables August 7, 2006 viii AIWN-UM-7001-01.
AIWN-UM-7001-01 ix A BO UT T HIS M ANUAL I NTROD UCTION This manual applies to ADC’ s Ethernet Network Interface Unit (ENIU) card (hereaf ter referred to as the “ENIU”).
About This Manual August 7, 2006 x AIWN-UM-7001-01 I NSPECTING Y OUR S HIPMENT Upon receipt of the equipment: • Unp ack each contain er and visually inspect the content s for signs of damage. If the equipment has been dam- aged in transit, immediately repor t the extent of dam age to the transport ation comp any and to ADC.
AIWN-UM-7001-01 1-1 1 Chapter O VERVIEW P RODUCT D ESCRIPTION Delivering a comprehensive set o f Ethernet services requires an intelligent Ethernet network interface unit (ENIU) to serve as the service demarcation point at the edge of the customer's network.
Chapter 1: Overview August 7, 2006 1-2 AIWN-UM-7001-01 F RONT P ANEL Each ENIU has three LEDs, a ST A TUS LED, a LPBK LED, and a LOS/LINK LED. Unde r normal operation the ENIU ST A TUS LED is green. Front p anel indi cators and controls ar e defined in T a ble 1-1 on p ag e 1-2 .
AIWN-UM-7001-01 2-1 2 Chapter I NSTALLATION When using the mounting bracket, allow six inches (15.3 cm) on both en ds of the ENIU for cable access. Inst all the ENIU using the following proce dures.
Chapter 2: Installation August 7, 2006 2-2 AIWN-UM-7001-01 P OWER AND G ROUND C ONNECTI ONS Power and ground connections are loca ted on the back of the ENIU. Ground Connection T o assure pr oper operation, the ground st ud located on the back of the ENIU (see Figure 2- 2 on page 2- 3 ) should be connected to a good earth ground.
August 7, 2006 Chapter 2: Installation AIWN-UM-7001-01 2-3 Power Connection Following local practices, att ach two p a ir of power supply wires fr om two sep arate power sou rces to the four pin power plug (p air 1: -48 VDC-A, RETURN-A a nd pair 2: -48 VDC-B, RETURN-B) on the ch assis backp la ne (se e Figure 2-3 for det ails) .
Chapter 2: Installation August 7, 2006 2-4 AIWN-UM-7001-01 C ABLING RJ-45 cable connections are made to both th e front and rear of the ENIU. DB-9 (command line interface) connection is made on the front an d the power connection is made on the rear .
August 7, 2006 Chapter 2: Installation AIWN-UM-7001-01 2-5 T able 2-1. 10/100 Mbp s Ethernet RJ-45 Connect or T able 2-2. 1000BaseT Ethernet RJ-45 Connector Optical Cables The maximum dist ance that a.
Chapter 2: Installation August 7, 2006 2-6 AIWN-UM-7001-01 DB-9 Communications Cable An RS-232 Craf t port is provided through a DB-9 connector . Refer to your work order to determine the required communications connections. After dete rmining the requir ed con nections , make the necessary connection .
AIWN-UM-7001-01 3-1 3 Chapter C OMMAND -L INE I NTERFACE (CLI) This section lists the commands used to operate the ENIU. Af ter the initial inst allation of an ENIU, most testing and local operations are co nducted with the Command Line Interface through a VT -100 compatible terminal.
Chapter 3: Provisioning August 7, 2006 3-2 AIWN-UM-7001-01 C OMMANDS O VERVIEW All settings are immediately saved. There is no se p arate ‘save’ command. Some settings (for example, save download) do not take ef fect until afte r the next CPU reset.
August 7, 2006 Chapter 3: Provisioning AIWN-UM-7001-01 3-3 Configuration Get Configuration Purpose: Show the current configured p a rame ter s. Command:[all privileges] GET CONFIGURATION Interface S peed and Negotiation Purpose: Configure speed and negot iation mechanism for the NETWOR K a nd SUBSCRIBER interfaces.
Chapter 3: Provisioning August 7, 2006 3-4 AIWN-UM-7001-01 Configure Keep Alive Purpose: Configure “keep alive” mode. When on, the ENIU will not generate an alarm event if the subscri ber interface loses link.
August 7, 2006 Chapter 3: Provisioning AIWN-UM-7001-01 3-5 Craft Port Con figuration Purpose: Configure user interaction with th e command line interpreter . Command:[RW , SECURE privilege] SET IDLE TIMEOUT <minutes> Identifies the number of minut es that the Craft port can remain idle before a logged in user is logged of f.
Chapter 3: Provisioning August 7, 2006 3-6 AIWN-UM-7001-01 Configure OAM for EXFO Operation Purpose: Configure OAM to interoperate with EXFO test equipment in a VLAN environment.
August 7, 2006 Chapter 3: Provisioning AIWN-UM-7001-01 3-7 User and Privilege Settings Purpose: Defines users to the system. Command: [SECURE privilege] SET USER <name> RO|RW|SECURE <password> CLEAR USER <name> User name and p asswords are specified as 1 to 15 alphanumeric characters.
Chapter 3: Provisioning August 7, 2006 3-8 AIWN-UM-7001-01 Configure Optical Thresh olds Purpose: On ENIUs that have optical interfaces, these commands configure the alarm thresholds as sociated with the power levels of the optical connections.
August 7, 2006 Chapter 3: Provisioning AIWN-UM-7001-01 3-9 Exit Purpose: Log of f of a command line session. Command: [all privileges] EXIT Inventory Purpose: Shows hardware and firmware versions as we ll as ADC cat alog and part numbers. Command: [all privileges] GET INVENTORY LED test Purpose: Perform an LED test for the fro nt panel L EDs.
Chapter 3: Provisioning August 7, 2006 3-10 AIWN-UM-7001-01.
AIWN-UM-7001-01 A-1 A Appendix S PECIFICATIONS S pecifications for t he ENIU are listed in T able A-1 . T able A-1. Ethernet NIU Specific ations P ARAMETER SPECIFICA TION Remark s Power Voltage –48VDC, or 110 to 240VAC (50–60 Hz) Operating Voltage +5 VDC Backplane connector Input Current 0.
Appendix A: S pecifications August 7, 2006 A-2 AIWN-UM-7001-01.
AIWN-UM-7001-01 B-1 B Appendix P RODUCT S UPPORT ADC Customer Service Group provides expert pre-sales su ppor t and tr aining for all of it s pro duct s. T echnical support is available 24 hours a day , 7 days a week by contacting t he ADC T echnical Assist ance Center .
Appendix B: Product Support August 7, 2006 B-2 AIWN-UM-7001-01.
AIWN-UM-7001-01 GL-1 G LOSSARY A ALM – Alarm AW G – American Wire Gauge C CLI – Command Line Interfa ce CO – Central Office CPE – Customer Premise Equipment E ENIU – Ethernet Network Inter.
Glossary August 7, 2006 GL-2 AIWN-UM-7001-01.
Certification and W arranty Limited W arranty Product warranty is deter mined by yo ur se rvice agreement. Refer to the ADC Warranty/Sof tware Handbook for additional information, or cont act your sales representative or C ustomer Service for d et ails.
World Headqua rters ADC T elecommunications, Inc. PO Box 1 101 Minneapolis, MN 55440-1 101 USA For T echnical Assist ance T el: 800.366.3 891 Ethernet Network Interface Unit (ENIU) User Manual Documen.
Een belangrijk punt na aankoop van elk apparaat ADC Network Unit (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen ADC Network Unit heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens ADC Network Unit vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding ADC Network Unit leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over ADC Network Unit krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van ADC Network Unit bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de ADC Network Unit kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met ADC Network Unit . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
