Gebruiksaanwijzing /service van het product LAP24EBA van de fabrikant Bretford
Ga naar pagina of 33
LAP24EBA LAP24EFR NOTEBOOK CART ASSEMBL Y Assembly Instructions for: INTERIOR E-UNIT REPOSITIONING / REPLACEMENT AND TIMER INST ALLA TION Parts List Q t y .
clip DET A I L 'A' DET A I L 'B ' E-Unit power cord bracket assembly bottom shelf Front View bracket assembly bracket assembly.
Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside.
DET A I L 'D ' Step 4 Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D', then carefully sliding out.
clip-rear Step 5 Reinstall the E-Units (set aside from being removed from the front) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Position to the rear of cart. 3. T ilt in and set bottom in back, in front of rear p anel cutout window .
Step 6 Reinstall the 7 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf.
Step 1 Remove 14 screws (2 per shelf) from rear panel that secure the 7 interior shelves (see DET AIL 'A'). DET A I L 'A ' E-UNIT REPOSITIONING: 'REAR TO FRONT' NOTE: UNP.
Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord bracket assembly Front View Unwind the power cords of the E-Units from the cord wrap brackets (on the rear panel).
DET A I L 'D ' DET AI L 'E' Step 3 Remove rear-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside.
Step 4 Reinstall the 7 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf.
Step 6 Reinstall the E-Units (set aside from being removed from the rear) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Position to the front of cart. 3. Tilt in and set against offset of bottom panel (of cart). 4. Grip the top and tilt to the upright position.
E-UNIT REPLACEMENT : 'REAR LOCA TION' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING Step 1 Remove 14 screws (2 per shelf) from rear panel that secure the 7 interior shelves (see DET AI L 'A').
Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord bracket assembly Front View Unwind the power cord(s) of the E-Unit(s) from the cord wrap bracket(s) on the rear panel.
DET A I L 'C ' DET A I L 'D ' Step 3 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside.
Step 4 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top. When repositioned correctly , the E-Unit(s) power switch should be visible from rear panel cutout window .
Step 5 Reinstall the 7 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf.
Step 1 Open both front doors of cart to access E-Unit(s). Unwind any length of E-Unit power cord remaining on the exterior rear panel cord wrap bracket(s). From underneath the bottom shelf (see Front View), carefully unclip the power cord(s) from the 2 clips located at the bottom panel of the cart.
clip DET A I L 'A' DET A I L 'B ' bracket assembly bracket assembly Step 2 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside.
Step 3 Carefully install replacement E-Unit(s) into position by placing bottom in first against the offset and tilting it in sideways to the top. When repositioned correctly , the E-Unit(s) power switch should face the front.
TIMER INST ALLA TION: 'E-UNIT A T REAR LOCA TION' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING DET A I L 'A ' Step 1 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET A IL 'A').
Step 2 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. Step 3 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove bracket assembly .
Step 5 Install timer with 2 screws. Adjust timer dial to current time. Step 4 Remove filler bracket from bracket by pulling upward. Discard filler bracket.
Step 6 Step 7 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in remaining 2 shelves into position as the bottom shelf.
DET A I L 'C ' Step 8 Reinstall 6 screws to rear panel that will secure the 3 interior shelves (see DET AIL 'C'). DO NOT OVER TIGHTEN SCREWS . Installation is now complete and ready for use. Adjust timer to current time when installation is complete and ready to be plugged back into power source.
SEE DET AIL 'A' SEE DET AIL 'B' bottom shelf TIMER INST ALLA TION: 'E-UNIT A T FRONT LOCA TION' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING Step 1 clip DET A I L 'A ' DET A I L 'B' bracket assembly bracket assembly Please read and follow all instructions thoroughly.
front-right front-left Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside.
Step 4 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out.
Step 5 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove bracket assembly . bottom flange- timer/bracket Step 6 Remove filler bracket from bracket by pulling upward.
Step 7 Install timer with 2 screws. Adjust timer dial to current time. Step 8 Install timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole shown. Make sure timer face is aligned with rear panel cutouts.
notch tab Step 9 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in remaining 2 shelves into position as the bottom shelf.
front-right front-left Step 1 1 Carefully reinstall E-Units into position by placing bottom in first against the offset and tilting it in sideways to the top (underneath the channel bracket of the cart top panel). When repositioned correctly , the E-Units power switch should face the front.
$8; $8; $8; $8; .
Part #031-6608 Rev . 08.29.05 CH P AD LOCK - DOOR: Bretford Bretford Ltd. 1 1000 Seymour Avenue T echnology House Franklin Park, IL 60131 2 Et ongate, 1 10 Windsor Road T EL : 847.678.2545 Slough, Berkshire SL1 2JA England 800.521.9614 TE L : 01753 53 99 55 FAX: 847.
Een belangrijk punt na aankoop van elk apparaat Bretford LAP24EBA (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Bretford LAP24EBA heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Bretford LAP24EBA vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Bretford LAP24EBA leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Bretford LAP24EBA krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Bretford LAP24EBA bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Bretford LAP24EBA kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Bretford LAP24EBA . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
