Gebruiksaanwijzing /service van het product 5900651 van de fabrikant Briggs & Stratton
Ga naar pagina of 44
5100699 Rev: M Briggs & Stratton Power Products Group, LLC. 5375 North Main Street Munnsville, NY 13409 800-933-6175 ProCut S Series 3-Wheel Riding Mowers OPERATOR’S MANUAL Model Number: Descrip.
Briggs & Stratton Power Products Group, LLC. Copyright © 2012 Briggs & Stratton Corporation Milwaukee, WI, USA. All rights reserved. FERRIS is a trademark of Briggs & Stratton Corporation Milwaukee, WI, USA. Contact Information: Briggs & Stratton Power Products Group, LLC.
1 Table of Contents Operator Safety .................................................. 2 Identification Numbers ............................................8 Safety Decals ..........................................................9 Safety Interlock System .
2 Operator Safety Operating Safety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety. Do not operate this machine unless you have been trained.
3 Operator Safety Slope Operation Operation on slopes can be dangerous. Using the unit on a slope that is too steep where you do not have adequate wheel traction (and control) can cause sliding, loss of steering, control, and possible rollover. You should not operate on a slope greater than a 5.
Enclosed Areas Only operate this unit outdoors and away from unventilated areas such as inside garages or enclosed trailers. The engine emits poisonous carbon monoxide gas and prolonged exposure in an enclosed area can result in serious injury or death.
5 2. Mow only in the daylight or with good artificial light, keeping away from holes and hidden hazards. 3. Be sure all drives are in neutral and parking brake is engaged before starting engine. Only start engine from the operator’s position. Use seat belts if provided.
6 Operator Safety 23. Use care when approaching blind corners, shrubs, trees or other objects that may obscure vision. 24. To reduce fire hazard, keep unit free of grass, leaves & excess oil. Do not stop or park over dry leaves, grass or combustible materials.
7 Operator Safety SERVICE AND MAINTENANCE To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
8 www.ferrisindustries.com Identification Numbers North American Models SAMPLE SAMPLE Operator Safety Figure. 1 Location of Identification Tags. A. Powerhead Identification Tag B.
9 Operator Safety SAFETY DECALS This unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing.
10 www.ferrisindustries.com Operator Safety Safety Icons The alert symbol is used to identity safety information about hazards that can result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used with the alert symbol to indicate the likelihood and the potential severity of the injury.
11 CONTROL FUNCTIONS The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section.
12 www.ferrisindustries.com Features and Controls PTO (Power Take Off) Switch The PTO switch engages and disengages the mower. Pull UP on the switch to engage, and push DOWN to disengage. Throttle Control The throttle controls engine speed. Move the throttle forward to increase engine speed and back to decrease engine speed.
13 Operation GENERAL OPERATING SAFETY Before first time operation: • Be sure to read all information in the Safety and Operation sections before attempting to operate this tractor and mower. • Become familiar with all of the controls and how to stop the unit.
14 www.ferrisindustries.com Operation WARNING If you do not understand how a specific control functions, or have not yet thoroughly read the FEATURES & CONTROLS section, do so now. Do NOT attempt to operate the tractor without first becoming familiar with the location and function of ALL controls.
15 Operation THREE WHEEL RIDER DRIVING PRACTICE The speed and steering controls of the Three Wheel rider are responsive , and learning to gain a smooth and efficient control of the rider’s forward, reverse, and turning movements will take some practice.
16 www.ferrisindustries.com Operation MOWING Before mowing, set the cutting height as described in the Troubleshooting, Adjustments & Service section. 1. Engage the parking brake. Make sure the PTO switch is disengaged and operator is seated in operator’s position with feet on foot rests.
17 When and How Often to Mow The time of day and condition of the grass greatly affect the results you’ll get when mowing. For the best results, follow these guidelines: 1. Mow when the grass is between three and five inches high. 2. Mow with sharp blades.
18 www.ferrisindustries.com Operation Proper Mulching Mulching consists of a mower deck which cuts and recuts clippings into tiny particles and which then blows them down INTO the lawn. These tiny particles decompose rapidly into by-products your lawn can use.
19 Operation STORAGE Temporary Storage (30 Days Or Less) Remember, the fuel tank will still contain some gasoline, so never store the unit indoors or in any other area where fuel vapor could travel to any ignition source. Fuel vapor is also toxic if inhaled, so never store the unit in any structure used for human or animal habitation.
20 www.ferrisindustries.com 20 www.ferrisindustries.com MAINTENANCE SCHEDULE & PROCEDURES The following schedule should be followed for normal care of your mower.
21 21 WARNING Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is still hot from recent operation. Do not allow open flame, smoking or matches in the area. Avoid over-filling and wipe up any spills. Do not remove fuel filter when engine is hot, as spilled gasoline may ignite.
22 www.ferrisindustries.com Regular Maintenance CHECK HYDRAULIC OIL LEVEL 1. Observe the oil reservoir (A, Figure 7). The oil level should be at the “FULL” line (C). 2. Before removing the reservoir cap, make sure the area around the reservoir cap is free of dust, dirt, or other debris.
23 Regular Maintenance Figure 9. Lubrication Points Mower Deck Lubrication Points LUBRICATION Lubricate the unit at the locations shown in Figure 9 as well as the following lubrication points. Grease: • foot pedal pivot • steering shaft • brake handle pivot • L/R brake lever pivots Use grease fittings when present.
24 www.ferrisindustries.com Regular Maintenance BATTERY MAINTENANCE Cleaning the Battery and Cables 1. Disconnect the cables from the battery, negative cable first (B, Figure 11). 2. Clean the battery terminals and cable ends with a wire brush until shiny.
25 Regular Maintenance SERVICING THE MOWER BLADES Removing the Mower Blade 1. See Figure 12. To remove the mower blade, wedge a wooden block between the mower blade and the mower deck housing to keep the mower blade from turning, then remove the mower blade and the blade retaining hardware.
26 www.ferrisindustries.com Figure 17. Tightening the Mower Blade for Installation A. Mower Blade Mounting Bolt B. Flat Washer C. Mower Blade Air Lift (Points Up For Installation) D. 4 X 4 Wooden Block D A B Sharpening the Mower Blade 1. Sharpen the mower blades with grinder, hand file, or electric blade sharpener.
27 TROUBLESHOOTING While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most common problems, their causes and remedies.
28 www.ferrisindustries.com Troubleshooting, Adjustment & Service Rider Troubleshooting Continued. PROBLEM CAUSE REMEDY Engine runs, but mower will not drive. Hydraulic release v alves in “open” position. P osition hydraulic release v alves in “drive” position.
29 Troubleshooting, Adjustment & Service TROUBLESHOOTING COMMON CUTTING PROBLEMS PROBLEM CAUSE REMEDY Streaking 1. Blades are not sharp. 2. Blades are worn down too far. 3. Engine speed is too slow. 4. Ground speed is too fast. 5. Deck is plugged with grass.
30 www.ferrisindustries.com Troubleshooting, Adjustment & Service MOWING HEIGHT ADJUSTMENT See Figure 18. The mowing height adjustment can be changed by turning the cutting height adjustment handle. To Raise the Mower Deck: Turn the cutting height adjustment handle (A, Figure 18) CLOCKWISE.
31 Troubleshooting, Adjustment & Service B C Figure 21. Mower PTO Belt Routing A. Spindle Pulley B. PTO Drive Belt C. Stationary Idler Pulley D. Spring-loaded Idler Pulley A D A A C Figure 20. Mower PTO Belt A. Idler Arm B. Stationary Idler Pulley C.
32 www.ferrisindustries.com FRONT Troubleshooting, Adjustment & Service TRANSMISSION DRIVE BELT REPLACEMENT 1. Park the tractor on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key.
33 Troubleshooting, Adjustment & Service DECK LIFT ROD TIMING ADJUSTMENT 1. Park machine on a flat, level surface. Disengage the PTO, stop the engine, and engage the parking brake.
34 www.ferrisindustries.com Troubleshooting, Adjustment & Service A A A Figure 27. Deck Height Position A. Cutting Height Indicator Figure 28. Setting the Blade Height Figure 29. Lift Rod Clevis Adjustment A. Jam Nut B. Adjustment Bolt C. Chain Hanger Clevis D.
35 Troubleshooting, Adjustment & Service TRANSMISSION FOOT CONTROL PEDAL NEUTRAL ADJUSTMENT If the tractor “creeps” (gradually moves forward or backwards) while the transmission foot control pedal is in the neutral position, then it may be necessary to adjust transmission foot control pedal neutral adjustment.
36 www.ferrisindustries.com Troubleshooting, Adjustment & Service PARKING BRAKE ADJUSTMENT 1. Park the machine on a flat, level surface. Disengage the PTO, stop the engine, and engage the parking brake. 2. Chock the drive tires and then release the parking brake handle 3.
37 Troubleshooting, Adjustment & Service REAR SUSPENSION ADJUSTMENT The shock assembly can be adjusted in two ways to allow the operator to customize the ride according to operator’s weight and/or operating conditions. You have the option of adjusting the spring pre-load and/ or the upper mounting position.
38 www.ferrisindustries.com Troubleshooting, Adjustment & Service BATTERY SERVICE Checking Battery Voltage A voltmeter can be used to determine condition of battery. When engine is off, the voltmeter shows battery voltage, which should be 12 volts.
39 To Starter Switch Starting V ehic le Battery T o Ground To Starter Switch Dischar ged V ehic le Battery Engine Block THIS HOOK-UP FOR NEGA TIVE GROUND VEHICLES MAKE CERT AIN VEHICLES DO NO T TOUCH .
40 www.ferrisindustries.com Specifications HYDRAULIC PUMP (S/N: All) PR-2KCC-GV1F-XXXX (5100642) WHEEL MOTORS: (S/N: 2014514856 & Below) LH / RH HGM-12C-4025 (S/N: 2014514857 - 2014545938) LH HGM-.
Thank you for purchasing Ferris commercial mowing equipment. Please take a few minutes to read this limited warranty information. It contains all the information you will need to have your Ferris mower repaired in the unlikely event that a breakdown covered by this limited warranty should occur.
ProCut S Series 3-Wheel Riding Mowers OPERATOR’S MANUAL Briggs & Stratton Power Products Group, LLC. 5375 North Main Street Munnsville, NY 13409 800-933-6175 www.
Een belangrijk punt na aankoop van elk apparaat Briggs & Stratton 5900651 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Briggs & Stratton 5900651 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Briggs & Stratton 5900651 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Briggs & Stratton 5900651 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Briggs & Stratton 5900651 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Briggs & Stratton 5900651 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Briggs & Stratton 5900651 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Briggs & Stratton 5900651 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
