Gebruiksaanwijzing /service van het product NSPVH21675 van de fabrikant Briggs & Stratton
Ga naar pagina of 24
Models SPVH21675 (7800441) NSPVH21675 (7800449) 21” V ARIABLE SPEED REAR DISCHARGE W ALK BEHIND MOWERS Manual No. 7102869 (Rev . ‘-’, 10/22/2008) TP10009165 NOTE: Specifications are correct at time of printing and are subject to change without notice.
SNAPPER is a trademark of Briggs & Stratton Power Products Group, LLC Jefferson, WI, USA. Briggs & Stratton Y ard Power Products Group Copyright © 2008, Briggs & Stratton Corporation Milwaukee, WI, USA.
W ARNING Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
www .snapper .com 2 Operator Safety ! ! IMPOR T ANT OPERA TOR SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons.
3 Operator Safety ! ! IMPOR T ANT OPERA TOR SAFETY INSTRUCTIONS (Continued) SAFE HANDLING OF GASOLINE (Continued From Previous Page) 7. Remove gas-powered equipment from the vehicle or trailer and refuel it on the ground. If this is not possible, then refuel equipment using a portable container , rather than a gasoline dispenser nozzle.
I C H Features and Controls A. Oil Fill Cap and Dipstick B. Fuel Filler Cap C. Recycling Cover D. Height Adjustment Lever E. Blade Control F . Rope Start Handle G.
Pre-Start Check List Make the following checks and perform the ser vice required before each start-up. 1. Check the guards, deflectors, grass bag, and covers to make sure all are in place and securely tightened. 2. Check the blade control (A, Figure 1) and drive handle (B) to insure they work freely .
Starting and Operation (Continued) Propelling the Mower 1. Start the engine. Refer to the Section entitled “Starting and Operation – Engine and Blade”. 2. Pull the drive handle lock lever (A, Figure 4) fully back to the unlock position. 3. Begin pushing the drive handle (B) forward to engage the wheel drive and propel the mower forward.
Cutting Height Adjustment 1. Pull the height adjusting lever (A, Figure 6) outward, and move to the desired cutting height. The highest cutting position is Notch 9 (B; also see Figure 7) . The lowest cutting position is Notch 1 (C) . Note: The lever will set all wheels to the same cutting height.
www .snapper .com 8 Operation Removing the Recycling Plug 1. Raise the rear discharge door (A, Figure 10) . 2. Remove the recycling plug (B) from the rear discharge chute. Note: The recycling plug should be removed only when bagging is desired, and should be replaced as soon as bagging operations are completed.
9 Maintenance Maintenance - Introduction T o retain the quality of the mower , use genuine SNAPPER replacement parts only . Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower , always mention the model and serial number .
W ARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT . Avoid serious burns, allow sufficient time for all components to cool.
Mower Blade Replacement Standard Blade Wear Limit 1. Inspect the blade (Figure 15) frequently for signs of excessive wear or damage: (A) New blade (B) Wear limit (notch starts) (C) Dangerous condition! Do not use on the mower! Replace with a new blade.
Wheel Drive Control Adjustment The drive handle (A, Figure 18) should engage the transmission when the handle is pushed forward, and should disengage the transmission when the handle is pulled fully back. If the transmission does not engage or disengage, adjustment may be performed as follows: 1.
Belt Ser vice On self-propelled mowers, the engine belt transmits power from the engine to the transmission that powers the rear wheels. Should the belt become worn, it could cause slip- page, which would impair mower performance. The condi- tion of the engine belt should be checked after every 25 hours of mower operation.
www .snapper .com 14 Maintenance Rear Cover Removal and Installation T o Remove the Rear Cover 1. Remove the three fasteners (A, Figure 23) securing the rear apron to the machine. 2. Remove the two fasteners (B) securing the rear cover to the machine.
15 Maintenance ITEM SERVICE PERFORMED REF . EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 5 X Initial Oil Change Page 9 X Periodic Oil Change Page 9 X* Air Pre-Clean.
PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not Start Using Recoil Starter 1. Fuel tank empty . 1. Fill fuel tank with fresh fuel. 2. Engine needs priming. 2. Prime. Check Engine Manual for Instructions. 3. Spark plug wire disconnected. 3. Place spark plug wire onto spark plug.
2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original pur chaser’ s residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of char.
Notes 18 www .snapper .com.
Slope Guide 19.
www .snapper .com 20 Notes.
21 Notes.
www .snapper .com Snapper Products 535 Macon Street McDonough, GA 30253 1-800-935-2967 22 21” V ARIABLE SPEED REAR DISCHARGE W ALK BEHIND MOWERS Engine Power Rating Information: The gross power rati.
Een belangrijk punt na aankoop van elk apparaat Briggs & Stratton NSPVH21675 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Briggs & Stratton NSPVH21675 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Briggs & Stratton NSPVH21675 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Briggs & Stratton NSPVH21675 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Briggs & Stratton NSPVH21675 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Briggs & Stratton NSPVH21675 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Briggs & Stratton NSPVH21675 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Briggs & Stratton NSPVH21675 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
