Gebruiksaanwijzing /service van het product BCO4816IA van de fabrikant BTC
Ga naar pagina of 24
Dual Digital Drive COMBO 4816IA User’s Manual.
DANGER INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM VORSICHT INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN A TTENTION RADIATION DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE. EVITER TOUTE EXPOSITION AUX RAYO NS.
FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Table of Contents INTRODUCTION 1 S YSTEM R EQUIREMENTS 2 P ACKAGE C ONTENTS 2 INSTALLATION 3 H OST I NTERFACE C ONNECTIONS 3 H ARDWARE I NSTALLATION 4 D RIVER I NSTALLATION 6 S OFTWARE I NSTALLATION 9.
Dual Digital Drive 1 INTRODUCTION Welcome to a multimedia world of CD-ReWritable technology, DVD-ROM capabilities and, memory card compatibility! This compact and high-performance CO MBO 4816IA frees up precious bay space and presents you as an IDE Co mbo (CD-RW+DVD ROM) Drive and a USB- connected card reader.
Dual Digital Drive 2 ♦ Smooth DVD playback System Requirements For IBM compatible PCs, the syst em requirements recommended are as follows: ♦ Pentium II, Celeron 400MHz & above with at least 64MB of memory ♦ Fast and sufficient hard disk space (minimum 200MB for installation, 1GB or more is recommended.
Dual Digital Drive 3 INSTALLATION Host Interface Connections Most current mainboard models have two IDE ports (primary and secondary), which can connect two IDE c ables. Two IDE cables allow you to connect up to four devices, but it is recommended that you separate IDE ports for your hard drive and your Dual Digital Combo Drive.
Dual Digital Drive 4 MASTER CSEL SLAVE JUMPER Improper or conflicting setting will c ause the unit not detected by your system. Hardware Installation 1. Turn off the power to your computer system. 2. Disconnect the power cord and all cables from the back of your computer, and then remove the cover of the computer.
Dual Digital Drive 5 5. If you have a sound card that can be connected to the drive, you can also connect the drive (as Audio-Out) and the sound card (as Audio-in) with a 4-pin audio cable. If your mainboad is integrated with built-in sound system, plug the 4-pin audio cable into the CD-IN connector on the mainboard as Audio-in.
Dual Digital Drive 6 Driver Installation For the Combo Drive For the Combo Drive itself, it’s an IDE device supporting Plug & Play and Windows 98SE/ME/2000/XP can automatic ally detect the drive and load the appropriate driver. For the Card Reader Windows 98SE/2000 If you are using Window 98SE or 2000, pleas e install the provided driver.
Dual Digital Drive 7 Click “OK” if you have already had USB cable connected (Refer to Hardware Installation, Step 6.).
Dual Digital Drive 8 Make sure to restart your computer. Windows ME/XP Since Windows ME and XP already have USB Mass Storage support, the card reader can be detected and wo rk fine without installing driver. However, we recommend that you in stall the provided driver to have more explicit operation status of the card reader, as described below.
Dual Digital Drive 9 After the driver installation, 4 extra ic ons with different card type indicated will show in Device Manager/My computer. And then you can use each slot of the card reader for file archiving/recording.
Dual Digital Drive 10 resolution 720 x 480 video playback. You can enjoy the wide range of educational and entertaining CD/DVD titles with sound and visual effect of theater quality. Windows Environment 1. Insert the application CD and the installation program will run automatically.
Dual Digital Drive 11 DVD Region Code Region Playback Control Management All DVD Video Playback systems have “Region Playback Control” management (RPC) which is required by Hollywood movie industry and defined by DVD Forum. This includes DVD-Video players and PC systems with DVD-Video capability.
Dual Digital Drive 12 About This Dual Digital Combo Drive This drive is also a RPC2 DVD-RO M drive and according to DVD-Forum, PC chip must be designed into DVD-ROM drives to record how many times a user has changed the region code.
Dual Digital Drive 13 OPERATION & CONNECTION Front Panel 1 2 7 83 4 9 10 11 6 5 1. Headphone Jack By plugging in the stereo mini ja ck here, you can listen to an audio disc directly playing from the drive with headphones. 2. Headphone Volume Control This rotary knob adjusts the audio out put level.
Dual Digital Drive 14 5. Led Indicator (Combo Drive) Flashes “ green ” while verifying or reading a CD/DVD. Flashes “ red ” while writing data.
Dual Digital Drive 15 Rear View 6 34 5 1. Digital Audio Output Connector If your sound card has a digital audio IEC958 format connector, you can connect it to this digital audio output connector with a 2-pin audio cable. 2. Analog Audio Output Connector This connector allows you to connec t the drive to your sound card with a 4-pin audio cable.
Dual Digital Drive 16 5. Pow er Supply Connector By plugging the computer’s power supply cable here, you can connect the drive and your computer system. 6. USB Cable Connect the USB cable to the U SB connector on the mainboard. The red wire of the cable needs to plug into Pin 1 on the board.
Dual Digital Drive 17 TECHNICAL DATA Interface Combo Drive: IDE Card Reader: USB 1.1 Form factor 5.25" Half Height Writing speed CD-R: 8X/16X/24X/32X/40X/48X CD-RW: 4X/10X/12X/16X/24X Writing mod.
Dual Digital Drive 18 Disc Format Supported Write Read CD-DA CD-ROM CD-ROM XA CD-EXTRA Video CD Photo CD CD-I CD-TEXT DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18) DVD+RW, DVD-RW Data buffer 2MB Disc loading Tray (motorised), Dust Sealed Audio output level Line out = 0.
Dual Digital Drive 19 Environment Combo Drive Temperature Operating 5°C to 45°C Non-operating -20°C to 60°C Humidity Operating 8% ~ 80%RH Non-operating 5% ~ 95%RH Card Reader Temperature Operating.
3100551770 Version 1.0 June 2003.
Een belangrijk punt na aankoop van elk apparaat BTC BCO4816IA (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen BTC BCO4816IA heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens BTC BCO4816IA vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding BTC BCO4816IA leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over BTC BCO4816IA krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van BTC BCO4816IA bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de BTC BCO4816IA kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met BTC BCO4816IA . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
