Gebruiksaanwijzing /service van het product 2010 Lucerne van de fabrikant Buick
Ga naar pagina of 472
In Brief ........................................................... 1 - 1 Instrument Panel ........................................ 1 - 2 Initial Drive Information ............................... 1 - 4 Vehicle Features ...............................
Appearance Care ................................... 6-100 Vehicle Identification ............................... 6-108 Electrical System .................................... 6-108 Capacities and Specifications ................... 6-117 Maintenance Schedule .
GENERAL MOTORS, GM, the GM Emblem, BUICK, the BUICK Emblem, and the name LUCERNE are registered trademarks of General Motors Corporation. This manual describes features that may or may not be on your specific vehicle either because they are options that you did not purchase or due to changes subsequent to the printing of this owner manual.
Safety Warnings and Symbols Warning Messages found on vehicle labels and in this manual describe hazards and what to do to avoid or reduce them. Danger indicates a hazard with a high level of risk which will result in serious injury or death. Warning or Caution indicates a hazard that could result in injury or death.
Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index.
✍ NOTES vi.
Instrument Panel ............................................. .1-2 Initial Drive Information ................................... .1-4 Remote Keyless Entry (RKE) System ............... .1-4 Remote Vehicle Start ..................................... .1-4 Door Locks .
Instrument Panel 1-2.
A. Outlet Adjustment on page 4-28 . B. DIC Operation and Displays on page 4-47 (If Equipped). C. Turn Signal/Multifunction Lever on page 4-5 . D. Instrument Panel Cluster on page 4-31 . E. Hazard Warning Flashers on page 4-3 . F. Audio System(s) on page 4-74 .
Initial Drive Information This section provides a brief overview about some of the important features that may or may not be on your specific vehicle. For more detailed information, refer to each of the features which can be found later in this owner manual.
When the vehicle starts, the parking lamps will turn on and remain on as long as the engine is running. The doors will be locked and the climate control system may come on. The engine will continue to run for 10 minutes. Repeat the steps for a 10-minute time extension.
Windows On vehicles with power windows, the switches are on the driver door armrest. Each passenger door has a switch that controls only that window. Press the switch to lower the window. Pull the switch up to raise it. For more information, see Power Windows on page 3-15 .
Power Seats Move the seat forward or rearward by moving the control forward or rearward Raise or lower the seat by moving the control up or down. See Power Seats on page 2-5 . Power Reclining Seatbacks To raise or recline the seatback, tilt the top of the control forward or rearward.
Power Lumbar On vehicles equipped with either a two-way or four-way lumbar, the control is located on the outboard side of the seats. For a detailed operation description see Power Lumbar on page 2-5 . Heated Seats On vehicles with heated seats, the controls are located on the front doors and the ignition must be on to use the feature.
Head Restraint Adjustment Do not drive until the head restraints for all occupants are installed and adjusted properly. For more information see Head Restraints on page 2-2 . Safety Belt Refer to the following sections for important information on how to use safety belts properly.
Mirror Adjustment Exterior Mirrors Controls for the outside power mirrors are located on the driver door armrest. 1. Press the left or right side of the selector switch located beneath the control pad to choose the driver or passenger side mirror.
Steering Wheel Adjustment The lever is located on the left side of the steering column. To adjust the lever: 1. Hold the wheel and pull the lever toward you. 2. Move the steering wheel up or down into a comfortable position. 3. Release the lever to lock the wheel in place.
Interior Lighting Courtesy Lamps When any door is opened, the interior lamps turn on to enter and exit the vehicle. Turn the instrument panel brightness control D located on the left side of the steering wheel, completely clockwise to manually turn on these lamps.
; : Manual operation of the parking lamps and other exterior lamps. 2 : Manual operation of the headlamps and other exterior lamps. - : Press to turn on the fog lamps. For more information, see: • Exterior Lamps on page 4-11 . • Daytime Running Lamps (DRL) on page 4-12 .
9 : Turns the wipers off. J : Press and release this paddle, located at the top of the turn signal/multifunction lever, to spray washer fluid on the windshield. See Windshield Wipers on page 4-6 and Windshield Washer on page 4-8 . Climate Controls A.
Vehicle Features Radio(s) O : Press to turn the system on and off. Turn to increase or decrease the volume. BAND: Press to choose between FM, AM, or XM™, if equipped.
Setting the Clock To set the time and date for the radio with CD (MP3): 1. Turn the ignition key to ACC/ACCESSORY or ON/RUN. 2. Press O to turn the radio on. 3. Press H and the HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year) displays. 4. Press the softkey located below any one of the tabs that you want to change.
Steering Wheel Controls If equipped, these controls are located on the right side of the steering wheel. w : Press to go to the next radio station stored as a favorite, or the next track, if a CD/DVD is playing. V b g : Press to silence the vehicle speakers only.
Navigation System The vehicle’s navigation system provides detailed maps of most major freeways and roads throughout the United States and Canada. After a destination has been set, the system provides turn-by-turn instructions for reaching the destination.
Vehicle Customization Some vehicle features can be programmed by using the DIC buttons on the instrument panel to the left of the steering wheel. These features include: • Language • Door Lock and Unlock Settings • Lighting • Chime Volume • Memory Settings • Remote Start See DIC Vehicle Customization on page 4-66 .
Lane Departure Warning (LDW) For vehicles with LDW, it is intended to help avoid lane change collisions. It provides a warning if the vehicle is crossing a lane without using a turn signal. LDW uses a camera to detect the lane markings. It only operates at speeds of 56 km (35 mph) or greater.
Keep the sensors on the vehicle’s rear bumper clean to ensure proper operation. The system can be disabled through the Driver Information Center (DIC). See Ultrasonic Rear Parking Assist (URPA) on page 3-36 for more information. Power Outlets The accessory power outlets can be used to plug in electrical equipment, such as a cellular telephone.
Performance and Maintenance Traction Control System (TCS) The traction control system limits wheel spin. The system turns on automatically every time the vehicle is started. • To turn off traction control, press and release i in front of the shift lever.
Note: The Tire Pressure Monitor can alert you about low tire pressure, but it does not replace normal monthly tire maintenance. It is the driver’s responsibility to maintain correct tire pressures. See Tire Pressure Monitor System on page 6-67 and Tire Pressure Monitor Operation on page 6-68 .
• When road and weather conditions are appropriate, use cruise control, if equipped. • Always follow posted speed limits or drive more slowly when conditions require. • Keep vehicle tires properly inflated. • Combine several trips into a single trip.
Automatic Crash Response In a crash, built in sensors can automatically alert an OnStar advisor who is immediately connected to the vehicle to see if you need help. How OnStar Service Works Q : This blue button connects you to a specially trained OnStar advisor to verify your account information and to answer questions.
Location information about the vehicle is only available if the GPS satellite signals are unobstructed and available. The vehicle must have a working electrical system, including adequate battery power, for the OnStar equipment to operate.
Head Restraints .............................................. .2-2 Front Seats ..................................................... .2-4 Manual Seats ............................................... .2-4 Power Seats ..................................
Head Restraints The vehicle’s front seats have adjustable head restraints in the outboard seating positions. { WARNING: With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/spinal injury in a crash.
Pull the head restraint up to raise it. To lower the head restraint, press the button, located on the top of the seatback, and push the restraint down. Push down on the head restraint after the button is released to make sure that it is locked in place.
Front Seats Manual Seats { WARNING: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving.
Power Seats To adjust a power seat, do any of the following: • Move the seat forward or rearward by sliding the control forward or rearward. • Raise or lower the front part of the seat cushion by moving the front of the control up or down. • Raise or lower the rear part of the seat cushion by moving the rear of the control up or down.
On vehicles with a four-way lumbar control, press the control forward or rearward to increase or decrease support in the lower seatback. Press the top or bottom of the control to raise or lower the support in the seatback. The lumbar support may need to be re-adjusted when changing the seating position.
Heated and Ventilated Seats On vehicles with heated and ventilated seats, the ignition must be on to use the feature. The buttons are located on the front doors. J (Heated Seat Cushion and Seatback): Press this button to heat the seat cushion and seatback.
When you press a button, the feature will turn on at the highest setting. Each time you press the button, the feature will decrease one temperature setting.
The vehicle must be in P (Park) to recall your memory positions. Press and release either button to recall the stored setting. Each time a memory button is pressed, a single beep sounds. If you use the remote keyless entry transmitter to enter your vehicle and the remote recall memory feature is on, automatic seat and mirror movement occurs.
Reclining Seatbacks Manual Reclining Seatbacks { WARNING: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
To recline the seatback, do the following: 1. Lift the recline lever. 2. Move the seatback to the desired position, then release the lever to lock the seatback in place. 3. Push and pull on the seatback to make sure it is locked. To return the seatback to an upright position, do the following: 1.
If the seats have power reclining seatbacks, the controls used to operate them are located on the outboard side of the seats. • Tilt the top of the control rearward to recline the seatback. • Tilt the top of the control forward to raise the seatback.
WARNING: (Continued) The lap belt cannot do its job either. In a crash the belt could go up over your abdomen. The belt forces would be there, not at your pelvic bones. This could cause serious internal injuries. For proper protection when the vehicle is in motion, have the seatback upright.
Rear Seats Rear Seat Pass-Through Door Your vehicle has a pass-through door that provides access to the trunk from the rear seats. See “Rear Seat Pass-Through Door” under Trunk on page 3-12 . Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly.
In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: You never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive.
Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 2-16.
The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... 2-17.
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces.
Q: If I am a good driver, and I never drive far from home, why should I wear safety belts? A: You may be an excellent driver, but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers.
Sit up straight and always keep your feet on the floor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt.
Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way. { WARNING: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way. { WARNING: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Q: What is wrong with this? A: The belt is buckled in the wrong buckle. { WARNING: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Q: What is wrong with this? A: The belt is over an armrest. { WARNING: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { WARNING: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Q: What is wrong with this? A: The belt is behind the body. { WARNING: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Q: What is wrong with this? A: The belt is twisted across the body. { WARNING: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to fix it.
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder except for the center front passenger position (if equipped), which has a lap belt. See Lap Belt on page 2-34 for more information. The following instructions explain how to wear a lap-shoulder belt properly.
4. If equipped with a shoulder belt height adjuster, move it to the height that is right for you. See “Shoulder Belt Height Adjustment” later in this section for instructions on use and important safety information. 5. To make the lap part tight, pull up on the shoulder belt.
Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger seating positions. Adjust the height so that the shoulder portion of the belt is centered on the shoulder. The belt should be away from the face and neck, but not falling off the shoulder.
Rear Safety Belt Comfort Guides This vehicle may have rear shoulder belt comfort guides for each outside passenger position in the rear seat. If not, they are available through your dealer/retailer. The guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults.
3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top. { WARNING: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured.
4. Buckle, position, and release the safety belt as described earlier in this section. Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guide, squeeze the belt edges together so that the safety belt can be removed from the guide.
Lap Belt This part is only for the lap belt. To learn how to wear a lap-shoulder belt, see Lap-Shoulder Belt on page 2-28 . You vehicle may have a center seating position. When you sit in the center front seating position, you have a lap safety belt, which has no retractor.
Safety Belt Extender If the vehicle’s safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer/retailer will order you an extender. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you.
The manufacturer’s instructions that come with the booster seat, state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below fit test: • Sit all the way back on the seat. Do the knees bend at the seat edge? If yes, continue.
{ WARNING: Never do this. Never allow two children to wear the same safety belt. The safety belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A safety belt must be used by only one person at a time.
{ WARNING: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt.
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints.
{ WARNING: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 40 km/h (25 mph), a 5.5 kg (12 lb) infant will suddenly become a 110 kg (240 lb) force on a person’s arms.
{ WARNING: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types.
{ WARNING: A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child’s abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure.
A forward-facing child seat (B) provides restraint for the child’s body with the harness. A booster seat (C-D) is a child restraint designed to improve the fit of the vehicle’s safety belt system. A booster seat can also help a child to see out the window.
Securing an Add-On Child Restraint in the Vehicle { WARNING: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle.
Where to Put the Restraint According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position.
WARNING: (Continued) Secure rear-facing child restraints in a rear seat, even if the airbag is off. If you secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat.
Lower Anchors and Tethers for Children (LATCH) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier. The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system.
Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash.
Lower Anchor and Top Tether Anchor Locations i (Top Tether Anchor): Seating positions with top tether anchors. j (Lower Anchor): Seating positions with two lower anchors. To assist you in locating the lower anchors, each seating position with lower anchors has two labels, near the crease between the seatback and the seat cushion.
To assist you in locating the top tether anchors, the top tether anchor symbol is located on the cover. The top tether anchors are located under the covers on the rear seatback filler panel.
Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top tether must be attached.
Notice: Do not let the LATCH attachments rub against the vehicle’s safety belts. This may damage these parts. If necessary, move buckled safety belts to avoid rubbing the LATCH attachments. Do not fold the empty rear seat with a safety belt buckled.
If the position you are using does not have a headrest or head restraint and you are using a dual tether, route the tether over the seatback. If the position you are using has a fixed headrest or head restraint and you are using a single tether, route the tether over the headrest or head restraint.
Securing a Child Restraint in a Rear Seat Position When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle.
3. Push the latch plate into the buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary. 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
Securing a Child Restraint in the Center Front Seat Position { WARNING: A child in a child restraint in the center front seat can be badly injured or killed by the frontal airbags if they inflate. Never secure a child restraint in the center front seat.
{ WARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag.
In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached. You will be using the lap-shoulder belt to secure the child restraint in this position. Follow the instructions that came with the child restraint.
5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
If a child restraint has been installed and the on indicator is lit, see “If the On Indicator is Lit for a Child Restraint ” under Passenger Sensing System on page 2-72 for more information. To remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position.
Here are the most important things to know about the airbag system: { WARNING: You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Airbags are designed to work with safety belts, but do not replace them.
{ WARNING: Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Where Are the Airbags? The driver frontal airbag is in the middle of the steering wheel. The right front passenger frontal airbag is in the instrument panel on the passenger side.
The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door. The roof-rail airbags for the driver, right front passenger, and second row outboard passengers are in the ceiling above the side windows.
{ WARNING: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death.
Frontal airbags may inflate at different crash speeds. For example: • If the vehicle hits a stationary object, the airbags could inflate at a different crash speed than if the vehicle hits a moving object.
Seat-mounted side impact and roof-rail airbags are not intended to inflate in frontal impacts, near-frontal impacts, rollovers, or rear impacts. A seat-mounted side impact airbag is intended to deploy on the side of the vehicle that is struck. Both roof-rail airbags will deploy when either side of the vehicle is struck.
What Will You See After an Airbag Inflates? After the frontal airbags and seat-mounted side impact airbags inflate, they quickly deflate, so quickly that some people may not even realize an airbag inflated. Roof-rail airbags may still be at least partially inflated for some time after they deploy.
{ WARNING: A crash severe enough to inflate the airbags may have also damaged important functions in the vehicle, such as the fuel system, brake and steering systems, etc. Even if the vehicle appears to be drivable after a moderate crash, there may be concealed damage that could make it diff icult to safely operate the vehicle.
Passenger Sensing System The vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator will be visible on the overhead console when the vehicle is started. The words ON and OFF, or the symbol for on and off, are visible during the system check.
{ WARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag.
The passenger sensing system is designed to turn on (may inflate) the right front passenger frontal airbag and seat-mounted side impact airbag anytime the system senses that a person of adult size is sitting properly in the right front passenger seat.
If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.
If the Of f Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat.
Additional Factors Af fecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status.
Adding Equipment to Your Airbag-Equipped Vehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Yes. If you add things that change your vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly. Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job.
Replacing Restraint System Parts After a Crash { WARNING: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash.
Keys .............................................................. .3-3 Remote Keyless Entry (RKE) System ............... .3-4 Remote Keyless Entry (RKE) System Operation .................................................. .3-5 Remote Vehicle Start ..
Storage Areas ............................................... .3-51 Glove Box .................................................. .3-51 Cupholders ................................................. .3-51 Front Storage Area ..............................
Keys { WARNING: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed.
See your dealer/retailer if a replacement key or additional key is needed. Notice: If you ever lock your keys in the vehicle, you may have to damage the vehicle to get in. Be sure you have spare keys. If you are locked out of your vehicle, contact Roadside Assistance.
Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 60 m (195 feet) away from the vehicle. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 3-4 .
Press and hold L for more than two seconds to activate the panic alarm. The turn signal lamps flash and the horn sounds repeatedly for 30 seconds. The alarm turns off when the ignition is moved to ON/RUN or L is pressed again. The ignition must be in LOCK/OFF for the panic alarm to work.
Remote Vehicle Start Your vehicle may have a remote starting feature. This feature allows you to start the engine from outside the vehicle. It may also start the vehicle’s heating or air conditioning systems, rear window defogger, and heated seats.
To manually shut off a remote start: • Aim the RKE transmitter at the vehicle and press the remote start button until the parking lamps turn off. • Turn on the hazard warning flashers. • Turn the ignition switch on and then off. The vehicle can be started remotely two separate times between driving sequences.
Doors and Locks Door Locks { WARNING: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked.
Power Door Locks On vehicles with power door locks, the switches are located on the front doors. " (Unlock): Press to unlock the doors. Q (Lock): Remove the key from the ignition and press to lock the doors. Delayed Locking This feature allows the driver to delay the actual locking of the doors.
Rear Door Security Locks Rear door security locks prevent passengers from opening the rear doors from the inside. The rear door security locks are located on the inside edge of each rear door. The rear doors must be opened to access them. To use the lock: 1.
Trunk { WARNING: Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Emergency Trunk Release Handle Notice: Do not use the emergency trunk release handle as a tie-down or anchor point when securing items in the trunk as it could damage the handle. The emergency trunk release handle is only intended to aid a person trapped in a latched trunk, enabling them to open the trunk from the inside.
Windows { WARNING: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Power Windows { WARNING: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed.
Express-Down Window This feature is on the front windows. Press the switch to the second position to activate the express-down feature. To stop the window as it is lowering, press down briefly on the switch again. Window Lockout o (Window Lockout): The rear window lockout button is located on the driver’s door armrest near the window switches.
Arming with the Power Lock Switch The alarm system will arm when you use either power lock switch to lock the doors while any door is open and the key is removed from the ignition. The alarm system will not arm if the truck is open when you use either power lock switch to lock the doors.
When trying to start the vehicle if the engine does not start and the security light on the instrument panel cluster comes on, there may be a problem with your theft-deterrent system. Turn the ignition off and try again. If the engine still does not start, and the key appears to be not damaged, try another ignition key.
Starting and Operating Your Vehicle New Vehicle Break-In Notice: The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: • Do not drive at any one constant speed, fast or slow, for the first 500 miles (805 km).
The steering can bind with the wheels turned off center. If this happens, move the steering wheel from right to left while turning the key to ACC/ACCESSORY. If this doesn’t work, then the vehicle needs service. B (ACC/ACCESSORY): This position lets the radio and windshield wipers operate while the engine is off.
Notice: Do not try to shift to P (Park) if the vehicle is moving. If you do, you could damage the transmission. Shift to P (Park) only when the vehicle is stopped. Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition to START.
Engine Coolant Heater The engine coolant heater can provide easier starting and better fuel economy during engine warm-up in cold weather conditions at or below 0°F ( − 18°C). Vehicles with an engine coolant heater should be plugged in at least four hours before starting.
Automatic Transmission Operation The vehicle may have a shift lever located either on the steering column or on the console between the seats. P (Park): This position locks the front wheels. It is the best position to use when you start the engine because the vehicle cannot move easily.
R (Reverse): Use this gear to back up. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped.
2 (Second): This position reduces vehicle speed even more than 3 (Third) without using the brakes. You can use 2 (Second) on hills. It can help control vehicle speed as you go down steep mountain roads, but then you would also want to use the brakes off and on.
A warning chime will sound if the parking brake is set, the ignition is on, and the vehicle speed is greater than 5 mph (8 km/h). The brake light will come on and stay on until the parking brake is released. See Brake System Warning Light on page 4-36 for more information.
Steering Column Shift Lever If the vehicle has a steering column shift lever, use this procedure to shift the vehicle into P (Park): 1. Hold the brake pedal down. 2. Move the shift lever into P (Park) by pulling the shift lever toward you and moving it up as far as it will go.
Leaving the Vehicle With the Engine Running { WARNING: It can be dangerous to leave the vehicle with the engine running. The vehicle could move suddenly if the shift lever is not fully in P (Park) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire.
Shifting Out of Park Automatic Transmission Shift Lock This vehicle has an electronic shift lock release system. The shift lock release is designed to: • Prevent ignition key removal unless the shif.
Parking Over Things That Burn { WARNING: Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust { WARNING: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { WARNING: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Mirrors Automatic Dimming Rearview Mirror The vehicle may have an automatic dimming inside rearview mirror with OnStar ® and/or a compass display. Automatic dimming reduces the glare from the headlamps of the vehicle behind you. The dimming feature comes on and the indicator light illuminates each time the vehicle is started.
To adjust for compass variance: 1. Find your current location and variance zone number on the following zone map. 2. Press and hold O until the zone number displays. The number shown is the current zone number. 3. Once the zone number displays, press O repeatedly until the correct zone number displays.
Outside Automatic Dimming Mirror If the vehicle has this feature, the driver side mirror adjusts for the glare of headlamps behind you. This feature is controlled by the on and off settings on the automatic dimming rearview mirror. See Automatic Dimming Rearview Mirror on page 3-32 for more information.
Outside Convex Mirror { WARNING: A convex mirror can make things, like other vehicles, look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on the right. Check the inside mirror or glance over your shoulder before changing lanes.
Object Detection Systems Ultrasonic Rear Parking Assist (URPA) For vehicles with the URPA system, it operates at speeds less than 8 km/h (5 mph), and assists the driver with parking and avoiding objects while in R (Reverse). The sensors on the rear bumper are used to detect the distance to an object up to 2.
How the System Works URPA comes on automatically when the shift lever is moved into R (Reverse). The rear display briefly illuminates to indicate the system is working. URPA operates only at speeds less than 8 km/h (5 mph). If the vehicle is above this speed, the red light on the rear display will flash.
When the System Does Not Seem to Work Properly If the URPA system will not activate due to a temporary condition, the message PARK ASSIST OFF will be displayed on the DIC and a red light will be shown on the rear URPA display when the shift lever is moved into R (Reverse).
SBZA Detection Zones The SBZA sensor covers a zone of approximately one lane over from both sides of the vehicle, 3.5 m (11 ft). This zone starts at each side mirror and goes back approximately 5 m (16 ft). The height of the zone is approximately between 0.
When the System Does Not Seem To Work Properly Occasional missed alerts can occur under normal circumstances and will increase in wet conditions. The system does not need to be serviced due to an occasional missed alert. The number of missed alerts will increase with increased rainfall or road spray.
SBZA Error Messages The following messages may appear in the DIC: SIDE BLIND ZONE ALERT SYSTEM OFF: This message indicates that the driver has turned the system off. SIDE BLIND ZONE SYS. UNAVAILABLE: This message indicates that the SBZA system is disabled because the sensor is blocked and cannot detect vehicles in the blind zone.
Lane Departure Warning (LDW) The vehicle may have a Lane Departure Warning (LDW) system. Read this entire section before using the system. { WARNING: The Lane Departure Warning (LDW) system does not steer the vehicle and is only an aid to help you stay in your driving lane.
How the System Works LDW uses a camera located between the inside rearview mirror and the windshield to detect the lane markings. @ (Lane Departure Warning): To turn LDW on and off, press the LDW control, located by the exterior headlamp control. An indicator on the control will light to indicate that LDW is on.
When the System Does Not Seem To Work Properly The LDW symbol will not appear when the system is having diff iculty seeing the lines on the road or if the view of the camera on the windshield is block.
Do not use this system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the transmitter.
2. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. It can usually be found where the hanging antenna wire is attached to the motor-head unit and may be a colored button. Press this button.
Programming Universal Home Remote — Fixed Code For questions or help programming the Universal Home Remote System, call 1-866-572-2728 or go to learcar2u.com. Most garage door openers sold before 1996 are Fixed Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting.
The garage door opener receiver (motor head unit) could also have a row of dip switches that can be used when programming the Universal Home Remote. If the total number of switches on the motor head a.
2. Write down the eight to 12 switch settings from left to right as follows: • When a switch is in the up position, write “Left.” • When a switch is in the down position, write “Right.” • If a switch is set between the up and down position, write “Middle.
5. After entering all of the switch positions, again, firmly press and release all three buttons at the same time. The indicator lights will turn on. 6. Press and hold the button that will be used to control the garage door until the garage door moves.
Storage Areas Glove Box Lift the glove box handle up to open it. Use the key to lock and unlock the glove box. Cupholders There are cupholders located in the full floor console, or in the front of the center seat console. Cupholders are also located in the rear armrest.
Rear Seat Armrest This vehicle has a rear seat armrest with cupholders. Pull the tab on the armrest forward, to access it. Convenience Net Use the convenience net, located in the rear, to store small loads as far forward as possible. The net should not be used to store heavy loads.
Instrument Panel Overview .............................. .4-3 Hazard Warning Flashers ............................... .4-3 H o r n ............................................................ .4-3 Tilt Wheel ...........................................
Lane Departure Warning (LDW) Light ............. .4-39 Engine Coolant Temperature Warning Light ..... .4-40 Engine Coolant Temperature Gage ................. .4-40 Tire Pressure Light ...................................... .4-41 Malfunction Indicator Lamp .
Instrument Panel Overview Hazard Warning Flashers The hazard warning flashers let you warn others that you have a problem. The hazard warning flasher button is located in the center of the instrument panel above the radio. | : Press to make the front and rear turn signal lamps flash on and off.
Power Tilt Wheel and Telescopic Steering Column For vehicles with a power tilt control, it is located on the left hand side of the steering column. To adjust the power tilt wheel: • Push the control up or down to tilt the steering wheel up or down.
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: G : Turn and Lane-Change Signals 23 : Headlamp High/Low-Beam Changer N : Windshield Wipers L : Windshield Washer Flash-To-Pass Feature. Information for these features is on the pages following.
Turn Signal On Chime If the turn signal is left on, a warning chime sounds and the Driver Information Center (DIC) will display TURN SIGNAL ON after driving about a mile as a reminder to turn it off.
Clear ice and snow from the wiper blades before using them. If frozen to the windshield, carefully loosen or thaw them. Damaged blades should be replaced. Heavy snow or ice can overload the wiper motor. A circuit breaker will stop the motor until it cools.
Windshield Washer { WARNING: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. J (Washer Fluid): Press and release this paddle, located at the top of the turn signal/multifunction lever, to spray washer fluid on the windshield.
See Traction Control System (TCS) on page 5-6 . When road conditions allow you to safely use it again, the cruise control can be turned back on. The cruise control buttons are located on left side of the steering wheel. T (On/Off): Press to turn cruise control on and of f.
Resuming a Set Speed If cruise control is set at a desired speed and the brakes are applied, this shuts off the cruise control. However, it does not need to be reset. Once your vehicle reaches a speed of about 40 km/h (25 mph) or more, press the +RES button on the steering wheel.
Erasing Speed Memory The cruise control set speed memory is erased by turning off the cruise control or the ignition. Exterior Lamps The exterior lamps control is located on the instrument panel to the left of the steering wheel.
2 (Headlamps): Turn the control to this position to turn on the headlamps together with the following lamps listed below. A warning chime sounds if the driver’s door is opened while the ignition switch is off and the headlamps are on.
When the DRL are on, only the low-beam headlamps will be on. The parking lamps, taillamps, sidemarker and other lamps will not be on. When it is dark enough outside, the low-beam headlamps will come on. The other lamps that turn on with the headlamps will also turn on.
Exterior Lighting Battery Saver If the exterior lamp button has been left on, the exterior lamps will turn off about 10 minutes after the ignition is turned to LOCK/OFF and a door has been opened. This protects against draining the battery if the headlamps or parking lamps are accidentally left on.
Theater Dimming This feature allows for a three to five second fade out of the courtesy lamps instead of immediate turn off. Delayed Exit Lighting If it is dark enough outside when you remove the key from the ignition, the interior lamps will turn on and stay on for about 25 seconds.
A high electrical load occurs when several of the following are on, such as: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets.
Accessory Power Outlet(s) The accessory power outlets can be used to plug in electrical equipment, such as a cellular telephone. The vehicle may have up to three power outlets depending on the type of front seat installed. If the vehicle has front bucket seats with a center console, there are two outlets inside the rear storage compartment.
Ashtray(s) Notice: If papers, pins, or other flammable items are put in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage the vehicle. Never put flammable items in the ashtray. For vehicles without the floor console, pull the tray located below the climate controls to reveal the ashtray.
A. Fan Control B. Temperature Control C. Air Delivery Mode Control D. Recirculation E. Air Conditioning F. Rear Window Defogger Operation ( (Off): Turns the climate control system of f. Outside air still enters the vehicle and is directed to the floor.
Air Delivery Mode Control: Turn clockwise or counterclockwise to change the direction of the airflow in the vehicle. To change the current mode, select one of the following: H (Vent): Air is directed to the instrument panel outlets. ) (Bi-Level): Air is divided between the instrument panel outlets and the floor outlets.
The air-conditioning system removes moisture from the air, so a small amount of water might drip under the vehicle while idling or after turning off the engine. This is normal. h (Recirculation): Press to turn the recirculation mode on. An indicator light below the button comes on to show that this mode is on.
Dual Automatic Climate Control System The heating, cooling, and ventilation for the vehicle can be controlled with this system. For vehicles with the remote start feature and it is activated, the climate control system heats or cools the inside of the vehicle, with the settings used before the vehicle was turned off.
Automatic Operation AUTO (Automatic Fan): When AUTO is selected on the fan control, the system automatically adjusts the fan speed. If the OnStar ® system is activated when this position is selected, the fan speed will lower. AUTO (Automatic Mode) 1.
Manual Operation 9 (Off): Turns the climate control system of f. Outside air still enters the vehicle and is directed to the floor. The airflow direction and temperature can be adjusted. If the temperature is adjusted while the system is off, the display will light to show the current settings.
W (Floor/Defog): This mode clears the windows of fog or moisture. Air is directed to the floor outlets, with some air directed to the windshield and side window outlets. The system turns off recirculation and runs the air-conditioning compressor unless the outside temperature is at or below freezing.
Sensors The solar sensor, located in the defrost grille, in the middle of the instrument panel, monitors the solar radiation. Do not cover the solar sensor or the system will not work properly. There is also an interior temperature sensor located next to the steering wheel that measures the temperature of the air inside the vehicle.
Rear Window Defogger The rear window defogger uses a warming grid to remove fog or frost from the rear window. < (Rear Defogger): Press to turn the rear window defogger on or off. An indicator light below the button comes on to show that the rear window defogger is on.
Outlet Adjustment Use the levers, located in the middle of the front outlets, to change the direction of the airflow. Use the thumbwheel located between the outlets to turn them on and off. If the vehicle has rear seat outlets, adjust the direction of the airflow using the lever in the center of each outlet.
To access the passenger compartment air filter, do the following: 1. Press the tabs back and left to remove the cover. 2. Insert a tool behind the push pin located on the inboard side of the air filter compartment to carefully pry the pin out.
4. Insert the new air filter by pushing until you hear a click. Reinstall the push pin and snap the cover into place. Warning Lights, Gages, and Indicators Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Instrument Panel Cluster The instrument panel cluster is designed to show how the vehicle is running. It shows how fast the vehicle is going, how much fuel has been used, and many other things needed to drive safely and economically. The vehicle has this cluster or one very similar to it.
Speedometer and Odometer The speedometer shows the vehicle speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far the vehicle has been driven, in either miles or kilometers. This vehicle has a tamper resistant odometer.
This chime and light are repeated if the driver remains unbuckled and the vehicle is in motion. If the driver safety belt is already buckled, neither the chime nor the light comes on.
Airbag Readiness Light The system checks the airbag’s electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module.
Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 2-72 for important safety information.
Charging System Light This light comes on briefly when the ignition key is turned to START, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/retailer. The light should go out once the engine starts.
When the ignition is on, the brake system warning light also comes on when the parking brake is set. The light will stay on if the parking brake does not fully release. If it stays on after the parking brake is fully released, it means there is a brake problem.
For vehicles with a Driver Information Center (DIC), see DIC Warnings and Messages on page 4-55 for all brake related DIC messages. Traction Control System (TCS) Warning Light For vehicles with a Traction Control System (TCS) and StabiliTrak ® warning light, this light comes on briefly when the engine is started.
StabiliTrak ® Indicator Light This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer/retailer.
Engine Coolant Temperature Warning Light This light comes on briefly while starting the vehicle. If it does not, have the vehicle serviced by the dealer/retailer. If the system is working normally the indicator light goes off. Notice: Driving with the engine coolant temperature warning light on could cause the vehicle to overheat.
Tire Pressure Light For vehicles with a tire pressure monitoring system, this light comes on briefly when the engine is started. It provides information about tire pressures and the Tire Pressure Monitoring System. When the Light is On Steady This indicates that one or more of the tires are significantly underinflated.
Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It ensures that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.
To prevent more serious damage to the vehicle: • Reduce vehicle speed. • Avoid hard accelerations. • Avoid steep uphill grades. • If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible. If the light continues to flash, when it is safe to do so, stop the vehicle.
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration.
Notice: Lack of proper engine oil maintenance can damage the engine. The repairs would not be covered by the vehicle warranty. Always follow the maintenance schedule in this manual for changing engine oil. This light comes on briefly while starting the engine.
Highbeam On Light This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 4-6 for more information. Fuel Gage The fuel gage shows about how much fuel is in the tank. An arrow on the fuel gage indicates the side of the vehicle the fuel door is on.
Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). All messages will appear in the DIC display located below the speedometer in the instrument panel cluster. The DIC buttons are located on the instrument panel, to the left of the instrument panel cluster.
DIC Buttons The buttons are the trip/fuel, vehicle information, customization, and set/reset buttons. The button functions are detailed in the following pages. 3 (Trip/Fuel): Press this button to display the odometer, trip odometers, fuel range, average economy, instantaneous economy, and average speed.
The trip odometer has a feature called the retro-active reset. This can be used to set the trip odometer to the number of kilometers (miles) driven since the ignition was last turned on. This can be used if the trip odometer is not reset at the beginning of the trip.
Average Economy Press the trip/fuel button until AVG ECONOMY displays. This display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number is calculated based on the number of L/100 km (mpg) recorded since the last time this menu item was reset.
When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See “CHANGE ENGINE OIL SOON” under DIC Warnings and Messages on page 4-55 . You should change the oil as soon as possible. See Engine Oil on page 6-17 .
Side Blind Zone If your vehicle has the Side Blind Zone Alert (SBZA) system, this display allows the system to be turned on or off. Press the vehicle information button until SIDE BLIND ZONE displays. Once in this display, press the set/reset button to select between ON or OFF.
Relearn Remote Key To access this display, the vehicle must be in PARK (P). This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. This procedure will erase all previously learned transmitters. Therefore, they must be relearned as additional transmitters.
To adjust for compass variance, use the following procedure: Compass Variance (Zone) Procedure 1. Do not set the compass zone when the vehicle is moving. Only set it when the vehicle is in P (Park). Press the vehicle information button until PRESS V TO CHANGE COMPASS ZONE displays.
To calibrate the compass, use the following procedure: Compass Calibration Procedure 1. Before calibrating the compass, check that the compass zone is set to the variance zone in which the vehicle is located. See “Compass Variance (Zone) Procedure” earlier in this section.
AUTOMATIC LIGHT CONTROL ON This message displays when the automatic headlamps are turned on. See Exterior Lamps on page 4-11 for more information. BATTERY SAVER ACTIVE This message displays when the system detects that the battery voltage is dropping beyond a reasonable level.
ENGINE OVERHEATED IDLE ENGINE Notice: If you drive your vehicle while the engine is overheating, severe engine damage may occur. If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. Do not increase the engine speed above normal idling speed.
HOOD OPEN If your vehicle has the remote start feature, this message displays when the hood is not closed properly. Make sure that the hood is closed completely. See Hood Release on page 6-13 . ICE POSSIBLE DRIVE WITH CARE This message displays when the outside air temperature is cold enough to create icy road conditions.
PARK ASSIST OFF If your vehicle has this feature, after the vehicle has been started, this message will reminder the driver that the Ultrasonic Rear Parking Assist (URPA) system has been turned off. Press the set/reset button to acknowledge this message and clear it from the DIC display.
SERVICE AIR BAG This message displays when there is a problem with the airbag system. Have your vehicle serviced by your dealer/retailer immediately. See Airbag Readiness Light on page 4-34 for more information. SERVICE BATTERY CHARGING SYSTEM This message displays when there is a problem with the generator and battery charging systems.
SERVICE PARK ASSIST If your vehicle has this feature, this message displays if there is a problem with the Ultrasonic Rear Parking Assist (URPA) system. Do not use this system to help you park. See Ultrasonic Rear Parking Assist (URPA) on page 3-36 for more information.
SERVICE THEFT SYSTEM This message displays when there is a problem with the theft-deterrent system programmed in the key. A fault has been detected in the system which means that the system is disabled and it is not protecting the vehicle.
SIDE BLIND ZONE ALERT SYSTEM OFF If your vehicle has the Side Blind Zone Alert (SBZA) system, this message displays when the SBZA system has been turned off. See Side Blind Zone Alert (SBZA) on page 3-38 and DIC Operation and Displays on page 4-47 for more information.
STARTING DISABLED SERVICE THROTTLE This message displays if the starting of the engine is disabled due to the electronic throttle control system. Have your vehicle serviced by your dealer/retailer immediately. This message only appears while the ignition is in ON/RUN, and will not disappear until the problem is resolved.
TRACTION CONTROL OFF This message displays when the Traction Control System (TCS) is turned off. Adjust your driving accordingly. See Traction Control System (TCS) on page 5-6 for more information. TRACTION CONTROL ON This message displays when the Traction Control System (TCS) is turned on.
DIC Vehicle Customization Your vehicle has customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers.
ESPANOL: All messages will appear in Spanish. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. AUTO DOOR LOCK This feature allows you to select when the vehicle’s doors will automatically lock.
REMOTE DOOR LOCK This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when locking the vehicle with the RKE transmitter if the doors are open.
NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. DELAY DOOR LOCK This feature allows you to select whether or not the locking of the vehicle’s doors will be delayed.
NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC.
PARK TILT MIRRORS If your vehicle has this feature, it allows you to select whether or not the outside mirror(s) will automatically tilt down when the vehicle is shifted into R (Reverse). See Park Tilt Mirrors on page 3-34 for more information. Press the customization button until PARK TILT MIRRORS appears on the DIC display.
NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. EASY EXIT SETUP If your vehicle has this feature, it allows you to select which areas will recall with the automatic easy exit seat feature.
MEMORY SEAT RECALL If your vehicle has this feature, it allows you to select your preference for the remote memory seat recall feature. See Memory Seat and Mirrors on page 2-8 for more information. Press the customization button until MEMORY SEAT RECALL appears on the DIC display.
FACTORY SETTINGS This feature allows you to set all of the customization features back to their factory default settings. Press the customization button until FACTORY SETTINGS appears on the DIC display. Press the set/reset button once to access the settings for this feature.
This system provides access to many audio and non audio listings. To minimize taking your eyes off the road while driving, do the following while the vehicle is parked: • Become familiar with the operation and controls of the audio system. • Set up the tone, speaker adjustments, and preset radio stations.
The date does not automatically display. To see the date press H while the radio is on. The date with display times out after a few seconds and goes back to the normal radio and time display. To change the time default setting from 12 hour to 24 hour or to change the date default setting from month/day/year to day/month/year: 1.
The date does not automatically display. To see the date press MENU and then softkey below the H tab while the radio is on. The date with display times out after a few seconds and goes back to the normal radio and time display.
Radio Data System (RDS) The radio may have the Radio Data System (RDS) feature. RDS is available for use only on FM stations that broadcast RDS information. This system relies upon receiving specific information from these stations and only works when the information is available.
Finding a Station BAND: Press to switch between FM, AM, or XM™ (if equipped). The selection displays. f (Tune): Turn to select radio stations. © SEEK ¨ : Press to go to the previous or the next station and stay there. To scan stations, press and hold either arrow for a few seconds until the radio beeps once.
The number of favorites pages can be setup using the MENU button. To setup the number of favorites pages: 1. Press the MENU button to display the radio setup menu. 2. Press the pushbutton located below the FAV 1-6 tab. 3. Select the desired number of favorites pages by pressing the pushbutton located below the displayed page numbers.
The radio may also be capable of adjusting all tone and speaker controls to the middle position by pressing the f knob for more than two seconds until the radio beeps once.
3. Turn the f knob, press the buttons below the right or left arrows displayed, or press the SEEK arrows to go to the previous or to the next XM station within the selected category. 4. To exit the category search mode, press the FAV button or BAND button to display favorites again.
Playing a CD Insert a CD partway into the slot, label side up. The player pulls it in and the CD should begin playing. If the ignition or radio is turned off while a CD in the player it stays in the player. When the ignition or radio is turned on, the CD starts to play where it stopped, if it was the last selected audio source.
f (Tune): Turn to select tracks on the CD currently playing. © SEEK ¨ : Press the left arrow to go to the start of the current track, if more than ten seconds have played. Press the right arrow to go to the next track. If either arrow is held, or pressed multiple times, the player continues moving backward or forward through the tracks on the CD.
CD/AUX (CD/Auxiliary): Press to play a CD while listening to the radio. The CD icon and a message showing disc and/or track number displays when a CD is in the player. Press this button again and the system automatically searches for an auxiliary input device, such as a portable audio player.
CD Messages CHECK DISC: If an error message displays and/or the CD comes out, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. • The road is very rough. When the road becomes smoother, the CD should play.
BAND: Press to listen to the radio while a portable audio device is playing. The portable audio device continues playing until it is stopped or turned off. CD/AUX (CD/Auxiliary): Press to play a CD while a portable audio device is playing. Press again and the system begins playing audio from the connected portable audio player.
• Minimize the length of the file, folder or playlist names. Long file, folder, or playlist names, or a combination of a large number of files and folders, or playlists can cause the player to be unable to play up to the maximum number of files, folders, playlists, or sessions.
When the CD contains only playlists and compressed audio files, but no folders, all files are located under the root folder. The folder down and the folder up buttons searches playlists (Px) first and then goes to the root folder. When the radio displays the name of the folder the radio displays ROOT.
Playing an MP3 Insert a CD partway into the slot (Single CD Player), or press the load button and wait for the message to insert disc (Six-Disc CD Player), label side up. The player pulls it in, and the CD should begin playing. f (Tune): Turn this knob to select MP3 files on the CD currently playing.
h (Music Navigator): If the radio has the MP3 feature, it has the music navigator feature to play MP3 files on the CD-R or CD-RW in order by artist or album. Press the pushbutton located below the music navigator tab. The player scans the disc to sort the files by artist and album ID3 tag information.
No XM Signal: The system is functioning correctly, but the vehicle is in a location that is blocking the XM™ signal. When the vehicle is moved into an open area, the signal should return. Loading XM: The audio system is acquiring and processing audio and text data.
Navigation/Radio System For vehicles with a navigation radio system, see the separate Navigation System manual. Bluetooth ® Vehicles with a Bluetooth system can use a Bluetooth capable cell phone with a Hands Free Profile to make and receive phone calls.
Bluetooth Controls Use the buttons located on the steering wheel to operate the in-vehicle Bluetooth system. See Audio Steering Wheel Controls on page 4-105 for more information. b g (Push To Talk): Press to answer incoming calls, to confirm system information, and to start speech recognition.
Pairing a Phone 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Pair”. The system responds with instructions and a four digit PIN number.
Linking to a Dif ferent Phone 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Change phone”. The system responds with “Please wait while I search for other phones”.
5. Say a name tag for the phone number. The name tag is recorded and the system responds with “About to store <name tag>. Does that sound OK?”. • If the name tag does not sound correct, say “No” and repeat Step 5. • If the name tag sounds correct, say “Yes” and the name tag is stored.
Using the Directory Command The directory command lists all of the name tags stored by the system. To use the directory command: 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Directory”. The system responds with “Directory” and then plays back all of the stored name tags.
Using the Delete All Name Tags Command The delete all name tags command deletes all stored phone book name tags and route name tags for OnStar (if present). To use the delete all name tags command: 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone.
4. Continue entering digits until the number to be dialed is complete. After the whole number has been entered, say “Dial”. The system responds with “OK, Dialing” and dials the number. • If an unwanted number is recognized by the system, say “Clear” at any time to clear the last number.
Receiving a Call When an incoming call is received, the audio system mutes and a ring tone is heard in the vehicle. • Press b g and begin speaking to answer the call. • Press c x to ignore a call. Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work.
Muting a Call During a call, all sounds from inside the vehicle can be muted so that the person on the other end of the call cannot hear them. To Mute a call 1. Press b g . The system responds with “Ready” followed by a tone. 2. Say “Mute Call”.
Voice Pass-Thru Voice Pass-Thru allows access to the voice recognition commands on the cell phone. See the cell phone manufacturers user guide to see if the cell phone supports this feature. This feature can be used to verbally access contacts stored in the cell phone.
3. Say the name tag to send. • If the system clearly recognizes the name tag it responds with “OK, Sending <name tag>” and the dial tones are sent and the call continues. • If the system is not sure it recognized the name tag properly, it responds “Dial <name tag>, Please say yes or no?” followed by a tone.
Audio Steering Wheel Controls Vehicles with audio steering wheel controls could differ depending on the vehicle’s options. Some audio controls can be adjusted at the steering wheel. w (Next): Press to go to the next radio station stored as a favorite, or the next track if a CD/DVD is playing.
Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet.
Cellular Phone Usage Cellular phone usage may cause interference with the vehicle’s radio. This interference may occur when making or receiving phone calls, charging the phone’s battery, or simply having the phone on. This interference causes an increased level of static while listening to the radio.
✍ NOTES 4-108.
Your Driving, the Road, and the Vehicle ........... .5-2 Defensive Driving .......................................... .5-2 Drunk Driving ................................................ .5-2 Control of a Vehicle .......................................
Your Driving, the Road, and the Vehicle Defensive Driving Defensive driving means “always expect the unexpected.” The first step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Everyone on page 2-14 .
Police records show that almost 40 percent of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving. In recent years, more than 17,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with about 250,000 people injured.
And, of course, actual stopping distances vary greatly with the surface of the road, whether it is pavement or gravel; the condition of the road, whether it is wet, dry, or icy; tire tread; the condition of the brakes; the weight of the vehicle; and the amount of brake force applied.
ABS can change the brake pressure to each wheel, as required, faster than any driver could. This can help the driver steer around the obstacle while braking hard. As the brakes are applied, the computer keeps receiving updates on wheel speed and controls braking pressure accordingly.
StabiliTrak ® System The vehicle may have the StabiliTrak system which combines antilock brake, traction and stability control systems and helps the driver maintain directional control of the vehicle in most driving conditions. This is accomplished by selectively applying any one of the vehicle’s brakes and reducing engine power.
The TCS and StabiliTrak ® light will flash when the system is limiting wheel spin. The system may be heard or felt while it is working, but this is normal.
It is recommended to leave the system on for normal driving conditions, but it may be necessary to turn the system off if the vehicle is stuck in sand, mud, ice or snow, and you want to “rock” the vehicle to attempt to free it. See If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 5-18 .
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Of f-Road Recovery The vehicle’s right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that the vehicle straddles the edge of the pavement.
Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle’s three control systems.
Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: • Drive defensively. • Do not drink and drive.
Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep-standing or flowing water.
Before Leaving on a Long Trip To prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: • Windshield Washer .
Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: • Keep the vehicle serviced and in good shape. • Check all fluid levels and brakes, tires, cooling system, and transmission.
Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 32°F (0°C) when freezing rain begins to fall, resulting in even less traction.
{ WARNING: Snow can trap engine exhaust under the vehicle. This may cause exhaust gases to get inside. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled.
If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow Slowly and cautiously spin the wheels to free the vehicle when stuck in sand, mud, ice, or snow. See Rocking Your Vehicle to Get It Out on page 5-19 . If the vehicle has a traction system, it can often help to free a stuck vehicle.
Rocking Your Vehicle to Get It Out Turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction or stability system. Shift back and forth between R (Reverse) and a forward gear, spinning the wheels as little as possible.
Tire and Loading Information Label A vehicle specific Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar). With the driver door open, you will find the label attached below the door lock post (striker).
Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Item Description Total A Maximum Vehicle Capacity Weight for Example 1 = 1,000 lbs (453 kg) B Subtract Occupant Weight 150 lbs (68 kg) × 2 = 300 lbs (136 kg) C Available Occupant and Cargo Weight = 7.
Item Description Total A Maximum Vehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg) B Subtract Occupant Weight 200 lbs (91 kg) × 5 = 1,000 lbs (453 kg) C Available Cargo Weight = 0 lbs (0 kg).
Certification Label A vehicle specific Certification label is found on the rear edge of the driver door. The label shows the gross weight capacity of your vehicle, called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo.
{ WARNING: Things you put inside the vehicle can strike and injure people in a sudden stop or turn, or in a crash. • Put things in the cargo area of the vehicle. In the cargo area, put them as far forward as you can. Try to spread the weight evenly.
Recreational Vehicle Towing Recreational vehicle towing means towing the vehicle behind another vehicle – such as behind a motorhome. The two most common types of recreational vehicle towing are known as dinghy towing and dolly towing. Dinghy towing is towing the vehicle with all four wheels on the ground.
Dolly Towing The vehicle can be towed using a dolly. To tow the vehicle using a dolly, follow these steps: 1. Put the front wheels on a dolly. 2. Put the gear shift lever in P (Park). 3. Set the parking brake. 4. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing.
Towing a Trailer { WARNING: The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly. For example, if the trailer is too heavy, the brakes may not work well — or even at all. The driver and passengers could be seriously injured.
Pulling A Trailer Here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure the rig will be legal, not only where you live but also where you will be driving. A good source for this information can be state or provincial police.
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle.
Total Weight on the Vehicle’s Tires Be sure the vehicle’s tires are inflated to the upper limit for cold tires. These numbers can be found on the Certification/Tire label. See Loading the Vehicle on page 5-19 . Make sure not to go over the GVW limit for the vehicle, including the weight of the trailer tongue.
Before starting, check all trailer hitch parts and attachments, safety chains, electrical connectors, lamps, tires and mirror adjustments. If the trailer has electric brakes, start the vehicle and trailer moving and then apply the trailer brake controller by hand to be sure the brakes are working.
When towing a trailer, the arrows on the instrument panel flash for turns even if the bulbs on the trailer are burned out. For this reason you may think other drivers are seeing the signal when they are not. It is important to check occasionally to be sure the trailer bulbs are still working.
Leaving After Parking on a Hill 1. Apply and hold the brake pedal while you: • start the engine, • shift into a gear, and • release the parking brake. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks. 4. Stop and have someone pick up and store the chocks.
Service ........................................................... .6-3 Accessories and Modifications ......................... .6-3 California Proposition 65 Warning .................... .6-4 California Perchlorate Materials Requirements .... .6-4 Doing Your Own Service Work .
Buying New Tires ........................................ .6-74 Different Size Tires and Wheels ..................... .6-76 Uniform Tire Quality Grading ......................... .6-76 Wheel Alignment and Tire Balance ................. .6-78 Wheel Replacement .
Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories an.
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.
Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 7-13 . Adding Equipment to the Outside of the Vehicle Things added to the outside of the vehicle can affect the airflow around it.
Gasoline Octane If the vehicle has the 3.9L V6 engine (VIN Code 1) or the 3.9L V6 engine (VIN Code M), use regular unleaded gasoline with a posted octane rating of 87 or higher. If the octane rating is less than 87, an audible knocking noise, commonly referred to as spark knock, might be heard when driving.
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly. In most cases, nothing should have to be added to the fuel.
Fuel E85 (85% Ethanol) The 8th digit of the Vehicle Identification Number (VIN) shows the code letter or number that identifies the vehicle’s engine. The VIN is at the top left of the instrument panel. See Vehicle Identification Number (VIN) on page 6-108 .
To ensure quick starts in the wintertime, the E85 fuel must be formulated properly for your climate according to ASTM specification D 5798. If you have trouble starting on E85, it could be because the E85 fuel is not properly formulated for your climate.
Filling the Tank { WARNING: Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the fuel pump island. Turn off the engine when refueling. Do not smoke near fuel or when refueling the vehicle.
{ WARNING: Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop.
Filling a Portable Fuel Container { WARNING: Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs. To help avoid injury to you and others: • Dispense fuel only into approved containers.
Hood Release To open the hood: 1. Pull the hood release handle inside the vehicle. It is located next to the parking brake pedal near the floor. 2. Then go to the front of the vehicle and pull the secondary hood release to the right. The hood latch is located under the hood, near the center, at the front edge of the grille.
Engine Compartment Overview When you open the hood on the 3.9L V6 engine, here is what you will see: 6-14.
A. Underhood Fuse Block on page 6-109 . B. Remote Positive (+) Battery Terminal. See Jump Starting on page 6-46 . C. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 6-39 . D. Engine Coolant Recovery Tank.
When you open the hood on the 4.6L V8 engine, here is what you will see: 6-16.
A. Underhood Fuse Block on page 6-109 . B. Remote Positive (+) Terminal. See Jump Starting on page 6-46 . C. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 6-39 . D. Engine Coolant Surge Tank and Pressure Cap.
When to Add Engine Oil If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 6-117 .
What Kind of Engine Oil to Use Look for three things: • GM6094M Use only an oil that meets GM Standard GM6094M. • SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50.
Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty.
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and filter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required.
Engine Air Cleaner/Filter See Engine Compartment Overview on page 6-14 for the location of the engine air cleaner/filter. When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/filter at the Maintenance II intervals and replace it at the first oil change after each 50,000 mile (80 000 km) interval.
To reinstall the cover: 1. Align the two hinges located on the inboard side of the cover. 2. Push the cover slightly down and towards the engine to engage the tabs in the hinges and align the two screws. 3. Tighten the two screws on the top of the engine air cleaner/filter cover.
How to Check Automatic Transmission Fluid (3.9L Engine) Because this operation can be a little diff icult, you may choose to have this done at the dealer/retailer service department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick.
Then, without shutting off the engine, follow these steps: 1. For the 3.9L V6 engine, locate the transmission fluid dipstick top which is a round loop with this symbol. See Engine Compartment Overview on page 6-14 for more information on location. 2.
If the fluid level is low, add only enough of the proper fluid to bring the level into the cross-hatched area on the dipstick. 1. Pull out the dipstick. 2. Using a long-neck funnel, add enough fluid at the dipstick hole to bring it to the proper level.
A. Coolant Surge Tank with Pressure Cap B. Electric Engine Cooling Fans { WARNING: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.
Engine Coolant (4.6L Engine) The cooling system in the vehicle is filled with DEX-COOL ® engine coolant. This coolant is designed to remain in the vehicle for five years or 150,000 miles (240 000 km), whichever occurs first. The following explains the cooling system and how to check and add coolant when it is low.
Notice: If an improper coolant mixture is used, the engine could overheat and be badly damaged. The repair cost would not be covered by the vehicle warranty. Too much water in the mixture can freeze and crack the engine, radiator, heater core, and other parts.
If no coolant is visible in the surge tank, add coolant as follows: How to Add Coolant to the Surge Tank { WARNING: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough.
You can remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot. 1. Turn the pressure cap slowly counterclockwise. If you hear a hiss, wait for that to stop.
Engine Coolant (3.9L Engine) The cooling system in the vehicle is filled with DEX-COOL ® engine coolant. This coolant is designed to remain in the vehicle for five years or 150,000 miles (240 000 km), whichever occurs first. The following explains the cooling system and how to check and add coolant when it is low.
Notice: If an improper coolant mixture is used, the engine could overheat and be badly damaged. The repair cost would not be covered by the vehicle warranty. Too much water in the mixture can freeze and crack the engine, radiator, heater core, and other parts.
How to Add Coolant to the Radiator { WARNING: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. { WARNING: Steam and scalding liquids from a hot cooling system can blow out and burn you badly.
If the coolant in the recovery tank is constantly low, you should have a dealer/retailer service department inspect the vehicle for leaks. Notice: If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured.
If Steam Is Coming From The Engine Compartment { WARNING: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Turn it off and get everyone away from the vehicle until it cools down.
If the temperature overheat gage is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slow for about 10 minutes. Keep a safe vehicle distance from the car in front of you.
Power Steering Fluid See Engine Compartment Overview on page 6-14 for information on the location of the power steering fluid reservoir. When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise.
Windshield Washer Fluid What to Use When the vehicle needs windshield washer fluid, be sure to read the manufacturer’s instructions before use. If the vehicle will be operating in an area where the temperature may fall below freezing, use a fluid that has suff icient protection against freezing.
Brakes Brake Fluid The brake master cylinder reservoir is filled with DOT 3 brake fluid. See Engine Compartment Overview on page 6-14 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down: • The brake fluid level goes down because of normal brake lining wear.
What to Add Use only new DOT 3 brake fluid from a sealed container. See Recommended Fluids and Lubricants on page 7-10 . Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.
Brake Wear This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly.
Brake Pedal Travel See your dealer/retailer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign that brake service might be required. Brake Adjustment Every time the brakes are applied, with or without the vehicle moving, the brakes adjust for wear.
Battery Refer to the replacement number on the original battery label when a new battery is needed. { DANGER: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm.
To be sure the vent hose (A) is properly attached, the vent hose connectors (B) must be securely reattached to the vent outlets (C) on each side of the battery and the vent assembly grommet (D) must be secured to the floor pan (E). Vehicle Storage { WARNING: Batteries have acid that can burn you and gas that can explode.
Jump Starting If the vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. { WARNING: Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you.
Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle. 3. Turn off the ignition on both vehicles.
{ WARNING: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle.
6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one.
Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
Headlamp Aiming The vehicle has a visual optical headlamp aiming system. The aim of the headlamps have been preset at the factory and should need no further adjustment. However, if the vehicle is damaged in a crash, the aim of the headlamps may be affected and adjustment may be necessary.
To adjust the vertical aim: 1. Open the hood. See Hood Release on page 6-13 for more information. 2. Locate the aim dot on the lens of the low-beam headlamp. 3. Record the distance from the ground to the aim dot on the low-beam headlamp. 4. At a wall, measure from the ground upward (A) to the recorded distance from Step 3 and mark it.
7. Locate the vertical headlamp aiming screws, which are under the hood near each headlamp assembly. The adjustment screw can be turned with a 6 mm male hex. 8. Turn the vertical aiming screw until the headlamp beam is aimed to the horizontal tape line.
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 6-57 . For any bulb changing procedure not listed in this section, contact your dealer/retailer. Halogen Bulbs { WARNING: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb.
To replace one of these bulbs: 1. Open the trunk. See Trunk on page 3-12 . 2. Remove the convenience net. 3. Remove the plastic wing nuts retaining the trunk trim. 4. Pull back the trunk trim. 5. Remove the three hex nuts holding the taillamp assembly in place.
Taillamps and Back-Up Lamps A. Taillamp B. Back-up Lamp To replace an auxiliary taillamp or back-up lamp bulb: 1. Open the trunk. See Trunk on page 3-12 . 2. Remove the three fasteners from the trunk trim. 3. Pull back the trunk trim to access the bulbs.
License Plate Lamp To replace one of these bulbs: 1. Remove the license plate. 2. Reach up through the opening above the license plate to access the two license plate lamps. 3. Turn the socket counterclockwise to remove. 4. Grasp the bulb in the socket and pull straight out.
To replace the wiper blade assembly: 1. Turn the ignition to ACC/ACCESSORY with the engine off. 2. Pull the windshield wiper assembly away from the windshield. 3. Squeeze the tabs on each side of the wiper blade assembly and slide the assembly off the end of the wiper arm.
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer.
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall.
(F) Uniform Tire Quality Grading (UTQG) : Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance.
(F) Tire Size : A combination of letters and numbers define a tire’s width, height, aspect ratio, construction type, and service description. The letter T as the first character in the tire size means the tire is for temporary use only.
Tire Terminology and Definitions Air Pressure : The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight : This means the combined weight of optional accessories.
Intended Outboard Sidewall : The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa) : The metric unit for air pressure. Light Truck (LT-Metric) Tire : A tire used on light duty trucks and some multipurpose passenger vehicles.
Radial Ply Tire : A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim : A metal support for a tire and upon which the tire beads are seated. Sidewall : The portion of a tire between the tread and the bead.
Inflation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inflation or over-inflation is all right.
How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are under-inflated. Check the tire’s inflation pressure when the tires are cold.
Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
At the same time a message to check the pressure in a specific tire appears on the Driver Information Center (DIC) display. The low tire pressure warning light and the DIC warning message come on at each ignition cycle until the tires are inflated to the correct inflation pressure.
TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle.
The TPMS sensors can also be matched to each tire/wheel position by increasing or decreasing the tire’s air pressure. If increasing the tire’s air pressure, do not exceed the maximum inflation pressure indicated on the tire’s sidewall.
Tire Inspection and Rotation We recommend that you regularly inspect your vehicle’s tires, including the spare tire, for signs of wear or damage. See When It Is Time for New Tires on page 6-73 for more information. Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km).
{ WARNING: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
You need new tires if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber. • The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric.
GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking and handling performance of your vehicle.
Dif ferent Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this may affect the way your vehicle performs, including its braking, ride and handling characteristics, stability, and resistance to rollover.
Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis.
{ WARNING: Using the wrong replacement wheels, wheel bolts, or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured.
Tire Chains { WARNING: If your vehicle has P235/55R17, or P245/50R18 size tires, do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts.
If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly.
Tire Sealant and Compressor Kit { WARNING: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death.
Read and follow all of the tire sealant and compressor kit instructions. The kit includes: A. On/Off Button B. Selector Switch (Sealant/Air or Air Only) C. Pressure Relief Button D. Pressure Gage E. Air Only Hose (Black) F. Sealant/Air Hose (Clear) G.
Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inflate a Punctured Tire Follow the directions closely for correct sealant usage. When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for 5 minutes.
7. Start the vehicle. The vehicle must be running while using the air compressor. 8. Turn the selector switch (B) clockwise to the Sealant + Air position. 9. Press the on/off (A) button to turn the tire sealant and compressor kit on. The compressor will inject sealant and air into the tire.
16. If the flat tire was able to inflate to the recommended inflation pressure, remove the maximum speed label from the sealant canister and place it in a highly visible location. The label is a reminder not to exceed 55 mph (90 km/h) until the damaged tire is repaired or replaced.
Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) To use the air compressor to inflate a tire with air only and not sealant: Always do a safety check first. See If a Tire Goes Flat on page 6-81 . 1. Remove the tire sealant and compressor kit from its storage location.
7. Start the vehicle. The vehicle must be running while using the air compressor. 8. Turn the selector switch (B) counterclockwise to the Air Only position. 9. Press the on/off (A) button to turn the compressor on. The compressor will inflate the tire with air only.
Removal and Installation of the Sealant Canister To remove the sealant canister: 1. Remove the plastic cover. 2. Unscrew the connector (B) from the canister (A). 3. Pull up on the canister (A) to remove it. 4. Replace with a new canister which is available from your dealer/retailer.
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 4-3 . { WARNING: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
Removing the Spare Tire and Tools The equipment you will need is located in the trunk. 1. Open the trunk. See Trunk on page 3-12 . 2. Turn the center retainer counterclockwise to remove it. 3. Lift and remove the compact spare tire cover. 4. Turn the retainer that secures the jack and wheel wrench counterclockwise and remove the washer.
The tools you will be using include the jack (A) and the wheel wrench (B). Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See Changing a Flat Tire on page 6-90 . 2. Turn the wheel wrench counterclockwise to loosen all the wheel nuts, but do no remove them yet.
{ WARNING: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.
5. Position the jack and raise the jack head until it fits firmly on the ridge in the vehicle’s frame nearest the flat tire. Do not raise the vehicle yet. 6. Put the compact spare tire near the flat tire. { WARNING: Getting under a vehicle when it is jacked up is dangerous.
8. Remove all wheel nuts and remove the flat tire. { WARNING: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
12. Lower the vehicle by turning the jack handle counterclockwise. Lower the jack completely. { WARNING: Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing.
Notice: Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See Capacities and Specifications on page 6-117 for the wheel nut torque specification.
To store the compact spare tire and tools: A. Center Retainer B. Compact Spare Tire Cover C. Retainer D. Washer E. Jack Container F. Spare Tire G. Wheel Wrench H. Jack I. Foam Insert J. Bolt 1. Open the trunk. See Trunk on page 3-12 . 2. Place the foam insert (I) in the trunk compartment.
6. Secure the compact spare tire and the jack container (E) with the washer (D) and the retainer (C). 7. Reinstall the compact spare tire cover (B). 8. Secure with the center retainer (A). The compact spare tire is for temporary use only. Replace the compact spare tire with a full-size tire as soon as you can.
Appearance Care Interior Cleaning The vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on the upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces.
Do not clean the vehicle using: • A knife or any other sharp object to remove a soil from any interior surface. • A stiff brush. It can cause damage to the vehicle’s interior surfaces. • Heavy pressure or aggressive rubbing with a cleaning cloth.
To clean: 1. Saturate a lint-free, clean white cloth with water or club soda. 2. Wring the cloth to remove excess moisture. 3. Start on the outside edge of the soil and gently rub toward the center. Continue cleaning, using a clean area of the cloth each time it becomes soiled.
Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt.
Washing Your Vehicle The best way to preserve the vehicle’s finish is to keep it clean by washing it often. Notice: Certain cleaners contain chemicals that can damage the emblems or nameplates on the vehicle.
Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible.
Aluminum or Chrome-Plated Wheels and Trim The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel.
Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on the vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.
Vehicle Identification Vehicle Identification Number (VIN) This legal identifier is in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside. The VIN also appears on the Vehicle Certification and Service Parts labels and certificates of title and registration.
Power Windows and Other Power Options Circuit breakers in the rear fuse block protect the power windows and other power accessories. When the current load is too heavy, the circuit breaker opens and closes, protecting the circuit until the problem is fixed or goes away.
Fuses Usage 1 Engine Control Module (ECM), Crank 2 Fuel Injectors Odd 3 Fuel Injectors Even 4 Air Conditioning Clutch Fuses Usage 5 Air Injection Reactor (AIR) Solenoid 6 Oxygen Sensor 7 Emission Devi.
Fuses Usage 9 Engine Control Module (ECM), Powertrain Control Module (PCM) 10 Climate Control System, Instrument Panel Cluster Ignition 1 11 Airbag System 12 Horn 13 Windshield Wiper 14 Fog Lamps 15 R.
Rear Underseat Fuse Block The rear fuse block is located under the rear seat on the driver side. The rear seat cushion must be removed to access the rear fuse block. Removing the Rear Seat Cushion Notice: If you touch the exposed wires with the metal on the seat cushion, you could cause a short that could damage the battery and or wires.
To reinstall the rear seat cushion, do the following: { WARNING: A safety belt that is not properly routed through the seat cushion or is twisted will not provide the protection needed in a crash. If the safety belt has not been routed through the seat cushion at all, it will not be there to work for the next passenger.
Fuses Usage 1 Fuel Pump 2 Left Park Lamp 3 Not Used 4 Right Park Lamp Fuses Usage 5 Engine Control Module (ECM)/Transmission Control Module (TCM) 6 Memory Module 7 Not Used 6-114.
Fuses Usage 8 Steering Wheel Illumination 9 Front Heated/Cooled Seat Module 10 Run 2 - Heated/Cooled Seats 11 Not Used 12 RPA Module 13 PASS-Key ® III System 14 Unlock/Lock Module 15 Magnetic Ride Co.
Fuses Usage 46 Rear Defogger (J-Case) 47 Electronic Leveling Control Compressor (J-Case) 48 Blower (J-Case) 49 Not Used Resistor Usage 50 Terminating Resistor Relays Usage 51 Not Used 52 Rear Defogger.
Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 7-10 for more information.
Application Capacities English Metric Transmission Fluid - Bottom Pan Removal 3.9L V6 Engine 7.4 qt 7.0 L 4.6L V8 Engine 7.4 qt 7.0 L Wheel Nut Torque 100 lb ft 140 Y All capacities are approximate. When adding, be sure to fill to the approximate level, as recommended in this manual.
Maintenance Schedule ..................................... .7-2 Introduction .................................................. .7-2 Scheduled Maintenance .................................. .7-3 Owner Checks and Services ........................... .7-8 Recommended Fluids and Lubricants .
Maintenance Schedule Introduction Notice: Maintenance intervals, checks, inspections, recommended fluids, and lubricants are necessary to keep this vehicle in good working condition. Damage caused by failure to follow scheduled maintenance might not be covered by the vehicle warranty.
Rotation of New Tires To maintain ride, handling, and performance of the vehicle, it is important that the first rotation service for new tires be performed when they have 8 000 to 13 000 km (5,000 to 8,000 miles). See Tire Inspection and Rotation on page 6-72 .
• Fluids visual leak check (or every 12 months, whichever occurs first). A leak in any system must be repaired and the fluid level checked. • Engine air cleaner filter inspection (vehicles driven in dusty conditions only). See Engine Air Cleaner/Filter on page 6-22 .
Additional Required Services At Each Fuel Stop • Engine oil level check. See Engine Oil on page 6-17 . • Engine coolant level check. See Engine Coolant (4.6L Engine) on page 6-28 or Engine Coolant (3.9L Engine) on page 6-32 . • Windshield washer fluid level check.
First Engine Oil Change After Every 80 000 km/50,000 Miles • Engine air cleaner filter replacement. See Engine Air Cleaner/Filter on page 6-22 . • Automatic transmission fluid change (severe ser.
Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter. Reset oil life system. •• Engine coolant level check. •• Windshield washer fluid level check. •• Tire inflation pressures check. •• Tire wear inspection.
Owner Checks and Services Starter Switch Check { WARNING: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position. • The ignition should turn to LOCK/OFF only when the shift lever is in P (Park). • The ignition key should come out only in LOCK/OFF.
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number, or specification can be obtained from your dealer/retailer. Usage Fluid/Lubricant Engine Oil Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol.
Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer/retailer. Maintenance Replacement Parts Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 22676970 A1627C Engine Oil Filter 3.
Engine Drive Belt Routing 3.9L V6 Engine 4.6L V8 Engine 7-12.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Services Performed 7-14.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Services Performed 7-15.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Services Performed 7-16.
Customer Assistance and Information .............. .8-2 Customer Satisfaction Procedure ..................... .8-2 Online Owner Center ..................................... .8-5 Customer Assistance for Text Telephone (TTY) Users ......................
Customer Assistance and Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Buick. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your GM dealer’s sales or service departments.
STEP THREE — U.S. Owners: Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle. However, in the United States, if you continue to remain unsatisfied after following the procedure outlined in Steps One and Two, you can file with the BBB Auto Line Program to enforce your rights.
STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps one and two, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration program.
Online Owner Center Online Owner Center (U.S.) — www.gmownercenter.com/buick Information and services customized for your specific vehicle — all in one convenient place.
Customer Assistance for Text Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Buick has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Buick by dialing: 1-800-83-BUICK.
GM Mobility Reimbursement Program This program, available to qualified applicants, can reimburse you up to $1,000 of the cost of eligible aftermarket adaptive equipment required for your vehicle, such as hand controls or a wheelchair/ scooter lift. The offer is available for a very limited period of time from the date of vehicle purchase/lease.
Coverage Services are provided up to 5 years/100,000 miles (160 000 km), whichever comes first. In the U.S., anyone driving the vehicle is covered. In Canada, a person driving the vehicle without permission from the owner is not covered. Roadside Assistance is not a part of the New Vehicle Limited Warranty.
Services Specific to Canadian Purchased Vehicles • Fuel delivery: Reimbursement is approximately $5 Canadian. Diesel fuel delivery may be restricted. Propane and other fuels are not provided through this service. • Lock-Out Service: Vehicle registration is required.
Courtesy Transportation Program To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for vehicles with the New Vehicle Limited Warranty (Base Warranty Coverage period in Canada) and extended powertrain, and hybrid specific warranty in both the U.
In addition, for U.S. customers, should you arrange transportation through a friend or relative, limited reimbursement for reasonable fuel expenses may be available.
Collision Parts Genuine GM Collision parts are new parts made with the same materials and construction methods as the parts with which your vehicle was originally built. Genuine GM Collision parts are your best choice to ensure that your vehicle’s designed appearance, durability, and safety are preserved.
If a Crash Occurs Here is what to do if you are involved in a crash. • Check to make sure that you are all right. If you are uninjured, make sure that no one else in your vehicle, or the other vehicle, is injured. • If there has been an injury, call emergency services for help.
Managing the Vehicle Damage Repair Process In the event that your vehicle requires damage repairs, GM recommends that you take an active role in its repair. If you have a pre-determined repair facility of choice, take your vehicle there, or have it towed there.
Reporting Safety Defects to the Canadian Government If you live in Canada, and you believe that your vehicle has a safety defect, notify Transport Canada immediately, in addition to notifying General Motors of Canada Limited.
Current and Past Model Order Forms Technical Service Bulletins and Manuals are available for current and past model GM vehicles. To request an order form, specify year and model name of the vehicle. ORDER TOLL FREE: 1-800-551-4123 Monday-Friday 8:00 AM - 6:00 PM Eastern Time For Credit Card Orders Only (VISA-MasterCard-Discover), visit Helm, Inc.
Event Data Recorders This vehicle has an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an airbag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed.
OnStar ® If the vehicle has OnStar and you subscribe to the OnStar services, please refer to the OnStar Terms and Conditions for information on data collection and use. Navigation System If your vehicle has a navigation system, use of the system may result in the storage of destinations, addresses, telephone numbers, and other trip information.
A Accessories and Modifications ............................ 6 - 3 Accessory Power ............................................ 3-20 Accessory Power Outlets ................................. 4-17 Additives, Fuel ......................................
Audio System (cont.) Setting the Clock ......................................... 4-75 Theft-Deterrent Feature ............................... 4-104 XM™ Satellite Radio Antenna System ........... 4-107 Audio System(s) ................................
Center Flex Storage Unit ................................. 3-51 Center Seat ................................................... 2-13 Chains, T ire ................................................... 6-80 Charging System Light .........................
Cruise Control .................................................. 4 - 8 Light .......................................................... 4-45 Cupholders .................................................... 3-51 Customer Assistance ....................
Electronic Immobilizer P ASS-Key ® III+ ........................................... 3-17 Electronic Immobilizer Operation P ASS-Key ® III+ ........................................... 3-17 Engine Air Cleaner/Filter ...................................
Fuel (cont.) G a g e ......................................................... 4-46 Gasoline Octane ........................................... 6 - 6 Gasoline Specifications .................................. 6 - 6 Fuel Economy Driving for Better ...
I Ignition Positions ............................................. 3-19 Inadvertent Power Battery Saver ....................... 4-16 Infants and Y oung Children, Restraints ............... 2-39 Inflation - T ire Pressure .............................
Lights (cont.) Oil Pressure ............................................... 4-44 On Reminder .............................................. 4-12 Passenger Airbag Status Indicator .................. 4-35 Safety Belt Reminders ..........................
N Navigation System, Privacy .............................. 8-18 Navigation/Radio System, see Navigation Manual ...................................................... 4-93 Net, Convenience ........................................... 3-52 New V ehicle Break-In .
P ASS-Key ® III+ Electronic Immobilizer Operation ................................................... 3-17 Perchlorate Materials Requirements, California ...... 6 - 4 Perimeter Lighting ........................................... 4-15 Phone Bluetooth ® .
Removing the Spare T ire and T ools ................... 6-91 Replacement Bulbs ......................................... 6-57 Replacement Parts Maintenance ............................................... 7-11 Reporting Safety Defects Canadian Government .
Service ........................................................... 6 - 3 Accessories and Modifications ......................... 6 - 3 Adding Equipment to the Outside of the V ehicle ..................................................... 6 - 5 Doing Y our Own Work .
Theft-Deterrent Feature .................................. 4-104 Theft-Deterrent Systems ................................... 3-16 Content Theft-Deterrent ................................ 3-16 P ASS-Key ® III+ Electronic Immobilizer ............ 3-17 P ASS-Key ® III+ Electronic Immobilizer Operation .
V V ehicle Control ........................................................ 5 - 3 Loading ...................................................... 5-19 Remote Start ................................................ 3 - 7 Running While Parked ............
Een belangrijk punt na aankoop van elk apparaat Buick 2010 Lucerne (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Buick 2010 Lucerne heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Buick 2010 Lucerne vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Buick 2010 Lucerne leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Buick 2010 Lucerne krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Buick 2010 Lucerne bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Buick 2010 Lucerne kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Buick 2010 Lucerne . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
