Gebruiksaanwijzing /service van het product 305 van de fabrikant Bush Hog
Ga naar pagina of 20
BU S H H O G ® ASSEMBL Y ● OPERA TION ● MAINTENANCE $4.00 Operator ’s Manual 3 0 5/3 06 S ERIES R OT A R Y CUTTERS 403 Part No. 62736.
CONGRA TULA TIONS! Y ou have invested in the best implement of its type on the market today . The care you give your Bush Hog implement will greatly determine your satisfaction with its performance and its service life.
305/306 SERIES ROT AR Y CUTTERS T ABLE OF CONTENTS SECTION/P ARA P AGE W arranty.................................................2 Dealer Preparation Check List ...............3 Safety Precautions .................................4 Federal Laws and Regulations .
BUSH HOG ® LIMITED W ARRANTY ✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯ Bush Hog warrants to the original purchaser of any new Bush Hog equipment, p.
DEALER PREP ARA TION CHECK LIST 305/306 SERIES ROT AR Y CUTTERS BEFORE DELIVERING MACHINE — The following check list should be completed. Use the Operator ’s Manual as a guide. ❒ 1. Assembly completed. ❒ 2. Gearbox filled with oil. ❒ 3. All fittings lubricated.
IMPORT ANT SAFETY PRECAUTIONS This symbol is used to call attention to safe- ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in serious bodily injury.
IMPORT ANT FEDERAL LA WS AND REGULA TIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERA TIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such).
1-1 INTRODUCTION We are pleased to have you as a Bush Hog cus- tomer. Your 305/306 Series Rotary Cutter has been carefully designed to give maximum service with minimum down time. This manual is provided to give you the necessary operating and maintenance instructions for keeping your rotary cutter in top operating condition.
7 NOTE Due to the many variations in tractor / imple- ment hitch points and corresponding differ- ences in distances between tractor PTO shafts and implement input shafts, drivelines may need to be sh.
8 Figure 2-3 H. Hold driveline sections parallel to each other and check for minimum 6 inches (15cm) overlap. Figure 2-4). If driveline has been marked for cutting, overlap will be the distance between two marks. If driveline has less than minimum overlap, do not use.
AVOID PLACING HANDS, FEET OR ANY OTHER BODY PARTS BENEATH THE CUTTER WHILE MAKING HEIGHT ADJUSTMENTS. The cutting height may be adjusted from 2” to 12” by selecting the appropriate hole in the adjusting bracket between the tailwheel frame and deck lugs.
ROTATING CUTTER BLADES. STAND CLEAR UNTIL ALL MOTION HAS STOPPED. TO AVOID AN ACCIDENTAL FALL FROM THE TRACTOR AND POSSIBLE INJURY BY THE MOWER, IT IS RECOMMENDED THAT THE TRACTOR BE EQUIPPED WITH ROPS (ROLLOVER PROTECTIVE SYSTEM) AND THAT A SEAT BELT BE USED BY THE OPER- ATOR FOR ALL MOWING OPERATIONS.
11 Figure 4-1 Lubrication (3) Before Each Use (2) Before Each Use (6) Before Each Use 4-4 BLADE REPLACEMENT (Figure 4-2) It is not necessary to remove the complete blade holder assembly to replace the blades. Blade bolts are accessible through a hole in the top of the cutter deck.
Figure 4-3 Spring Length turning blades. If clutch does not slip, contact your authorized Bush Hog dealer. C. Retighten nuts to within 1/64” of original posi- tion. Initial spring length is shown in Figure 4-3. 4-6 SLIP CLUTCH ADJUSTMENT The slip clutch is factory preset to the correct torque for protecting implement and tractor.
13 4-8 TROUBLESHOOTING PROBLEM PROBABLE CAUSE REMEDY Uneven Cut Cutter not level side to side. See SECTION II Worn or bent blades. Replace blades per paragraph 4-4. Stripping or Windrowing Possible build-up of material under Clean cutter. cutter. Cutter not level.
PRE-ASSEMBL Y SAFETY PRECAUTIONS THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY. 1. Wear personal protective equipment such as, but not limited to protection for eyes, ears, feet, hands, lungs and head when assembling the equipment.
SECTION V ASSEMBL Y IMPORTANT Tighten all fasteners to specifications on Torque Chart unless otherwise indicated. 5-1 ST ANDARD 3-POINT HITCH (Figure 5-1) To attach a standard duty hitch to your cutter: Remove the lift pins and all bolts from the hitch.
SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge.
T ORQUE SPECIFICA TIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* BOLT DIAMETER WRENCH (IN.
BUSH HOG , L .L .C. ® P .O. Box 1039 ● Selma, AL 36702-1039 T elephone (334) 874-2700 ● www.bushhog.com.
Een belangrijk punt na aankoop van elk apparaat Bush Hog 305 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Bush Hog 305 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Bush Hog 305 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Bush Hog 305 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Bush Hog 305 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Bush Hog 305 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Bush Hog 305 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Bush Hog 305 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
