Gebruiksaanwijzing /service van het product LS1440 van de fabrikant Bushnell
Ga naar pagina of 20
INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. ENGLISH Miter Sa w MODEL LS1440 002146 DOUBLE INSULA TIO.
2 SPECIFICATIONS Blade diameter ................................................................................................................. ................................... 355 mm Hole diameter.................................................
3 GENERAL SAFETY RULES GEA001-3 W ARNING: Read all instructions. F ailure to f ollow all instructions listed below ma y result in electric shock, fire and/or serious injur y . The term “power tool” in all of the warnings listed below ref ers to your mains-operated (corded) po wer tool or batter y- operated (cordless) pow er tool.
4 or storing power tools. Such pre ventive saf ety measures reduce the risk of star ting the power tool accidentally . 19. Store idle power tools out of the reach of c hil- dren and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
5 27. Select saw blades in relation to the material to be cut. 28. T ake care when slotting. 29. Replace the kerf board when w orn. 30. Do not use saw blades manufactured from high speed steel. 31. Some dust created fr om operation contains chemicals known to cause cancer , birth defects or other reproductive harm.
6 INST ALLA TION Bench mounting When the tool is shipped, the handle is lock ed in the lowered position by the handle latch. Release the handle latch by low er ing the handle slightly and turn the handle latch to the released position.
7 Kerf boar d This tool is provided with the k erf board in the tur n base to minimize tearing on the exit side of a cut. If the k erf groov e has not yet been cut in the kerf board by the factory , you should cut the groov e before actually using the tool to cut a workpiece.
8 Fence plate The fence plate is designed to pre vent smaller cutting scraps from jamming inside the blade case. The f ence plate mov es r ight or left automatically as the turn base is rotated.
9 Press the shaft lock to loc k the spindle and use the socket wrench to loosen the hex bolt countercloc kwise. Then remov e the hex bolt, outer flange and blad e.
10 Slip the pin on the blade guard into the slot in the guide arm while returning the blade guard to its original fully closed position. Then tighten the he x bolt clock- wise to secure the center cov er. Lo wer the handle to make sure that the blade guard mov es proper ly .
11 Horizontal vise (Accessory) The horizontal vise can be installed on either the left or right side of the base. When performing 15 ° or greater miter cuts, install the horizontal vise on the side opposite the direction in which the turn base is to be tur ned.
12 leav e a mar k (sa w mar k) in the wo r kpiece and the precision of the cut will be impaired. 1. Press cutting Secure the workpiece with the vise. Switch on the tool without the blade making any contact and wait until the b lade attains full speed before low- ering.
13 After changing the miter angle, cut the wood f acing at that selected angle. If there is a gap between the b lade, the wood facing and the work- piece, mov e the wood facing slightly in the direct ion of the arrow and cut it again. CA UTION: • Use straight wood of e ven thickness as the w ood facing.
14 MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore attempting to perform inspection or maintenance. WA R N I N G : • Alwa ys be sure that the blade is sharp and clean for the best and safest performance.
15 Adjusting for smooth handle action The hex loc k nut which holds the gear housing and the arm has been factory adjusted to assure smooth handle action up and down and to guarantee pre- cise cutting. Do not tamper with it. Should looseness dev elop at the gear hous- ing and arm connection, perform the following adjustment.
16 A CCESSORIES CA UTION: • These accessories or attachments are recommended for use with y our Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injur y to persons. Only use accessory or attachment for its stated purpose.
Memo 17.
Memo 18.
Memo 19.
Makita Cor poration 883619D8.
Een belangrijk punt na aankoop van elk apparaat Bushnell LS1440 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Bushnell LS1440 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Bushnell LS1440 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Bushnell LS1440 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Bushnell LS1440 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Bushnell LS1440 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Bushnell LS1440 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Bushnell LS1440 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
