Gebruiksaanwijzing /service van het product 4054 van de fabrikant Calculated Industries
Ga naar pagina of 52
C ONSTRUCTION M ASTER ® 5 En Español ADV ANCED FEET -INCH-FRACTION CALCULA TOR Model 4054 Pocket Reference Guide ➡ ➡ Insert This Direction .
The Construction Master 5 calculator helps you save time, cut costly errors and build like a pro! Quickly Solve: • Feet-Inches-Fractions, Y ards, Metric Dimensional Problems and Conversions • Prob.
GETTING ST ARTED ...............................1 KEY DEFINITIONS/FUNCTIONS ..........1 Basic Function Keys ............................1 Dimension Keys ...................................2 Arc/Circle Keys ....................................4 Right T riangle/Roof Framing Keys .
Circle Area and Circumference .........24 Arc Angle or Degree ..........................24 Concrete V olume for Driveway ..........25 Concrete Columns .............................25 Complex Concrete V olume ................26 RIGHT ANGLE/FRAMING ....
P OCKET R EFERENCE G UIDE — 1 KEY DEFINITIONS / FUNCTIONS Basic Function Keys + – x Arithmetic operation keys. ÷ = 0 – 9 Keys used for entering and • numbers. % Percent Key — Four-func- tion (+, –, x, ÷) percent key . O Off Key — Turns all power off, clearing all non-perma- nent registers.
P OCKET R EFERENCE G UIDE — 2 ® Recall Key — Used with other keys to recall stored values and settings. μ Memory Key — Adds the displayed value to Memory . Clears when the calculator is shut off. Ç μ Memory Minus (M–) — Subtracts the displayed value from Memory .
P OCKET R EFERENCE G UIDE — 3 i Inch Key — Enters or con- verts to Inches . Entry can be whole or decimal num- bers. Also used with the / key for entering fractional inch values (e.g., 9 i 1 /2 ). Repeated presses during conversions toggle between Fractional and Decimal Inches.
P OCKET R EFERENCE G UIDE — 4 w Weight Key — Enters or converts (a volume value) to T ons, Pounds, Metric T ons or Kilograms . Repeated presses will cycle through these units. Arc/Circle Keys C Circle Key — Calculates Circle Area and Circumference based on entered Diameter .
P OCKET R EFERENCE G UIDE — 5 a Dimension 9 i p an Angle 3 0 p a Ratio 0 • 7 5 Ç p a Percentage 7 5 % p A Pitch entry will remain in permanent storage until revised or reset. A solution will be replaced by its entered value once the calculator is cleared.
P OCKET R EFERENCE G UIDE — 6 Ç H Irregular Pitch — Enters Irregular Pitch used to cal- culate lengths of the Irregular Hip/V alley and Jack rafters. j Jack Key — Calculates Jack rafter lengths on the Regular -pitched roof side. Ç j Irregular Jack — Calculates Jack rafter lengths on the Irregular -pitched roof side.
P OCKET R EFERENCE G UIDE — 7 Stair Layout Key s Stair Key — Given Rise and/or Run and entered/ stored variables, calculates or displays: Press Result 1 Riser Height 2 Number of Risers 3 Riser Ove.
P OCKET R EFERENCE G UIDE — 8 Stair Settings Y ou may set “desired Riser height” and “desired T read width” to any value by using the following keys: Ç 7 Riser Height — Stores a desired Riser height other than 7-1/2” (default) . For example, enter 8 Inches: 8 i Ç 7 .
P OCKET R EFERENCE G UIDE — 9 Ç √ x 2 — Squares the value in the display . √ Square Root Key — Used to find the Square Root of a non-dimensional or area value.
P OCKET R EFERENCE G UIDE — 10 ® = Paperless T ape – Useful for checking figures, as it scrolls through your past 20 entries or calculations. Press ® = to access Paperless T ape mode. Press + or – to scroll for- ward or backward. Press = to exit mode and continue with a new entry or calcula- tion.
P OCKET R EFERENCE G UIDE — 11 PREFERENCE SETTINGS Press Ç , then % , then keep pressing % to toggle through the main settings. Press the + key to advance within sub-setting.
P OCKET R EFERENCE G UIDE — 12 (Cont’d) PRESS : SETTING--FUNCTION Fourth press of % : Meter Linear Displays: -- 0.000 M + -- FLOTNTE M (floating point) + -- 0.000 M (repeats options) Fifth press of % : Decimal Degree Displays: -- 0.00º + -- FLOTNTE (floating point) + -- 0.
P OCKET R EFERENCE G UIDE — 13 ENTERING DIMENSIONS Linear Dimensions When entering Feet-Inch values, enter dimensions from largest to smallest — Feet before Inches, Inches before Fractions. Enter Fractions by entering the numerator (top number), pressing / (Fraction Bar key) and then the denomina- tor (bottom number).
P OCKET R EFERENCE G UIDE — 14 Linear Conversions Convert 10 Feet 6 Inches: KEYSTROKE DISPLA Y o o 0. 1 0 f 6 i 10 PIES 6 PULG Ç y 3.5 YD Ç i 126 PULG Ç m 3.200 M Ç c 320.04 CM Ç M 3200.4 MM Convert 14 Feet 7-1/2 Inches to Decimal Feet: KEYSTROKE DISPLA Y o o 0.
P OCKET R EFERENCE G UIDE — 15 Square and Cubic Conversions Convert 14 Square Feet to Square Y ards: KEYSTROKE DISPLA Y o o 0. 1 4 f f 14 PIES CUAD Ç y 1.555556 YD CUAD (1.6 square yards) Convert 25 Square Y ards to Square Feet: KEYSTROKE DISPLA Y o o 0.
P OCKET R EFERENCE G UIDE — 16 Adding and Subtracting Strings of Dimensions Add the following measurements: • 6 Feet 2-1/2 Inches • 1 1 Feet 5-1/4 Inches • 18.
P OCKET R EFERENCE G UIDE — 17 Dividing Dimensions Divide 15 Feet 3-3/4 Inches into thirds (divide by 3): KEYSTROKE DISPLA Y o o 0. 1 5 f 3 i 3 / 4 ÷ 3 = 5 PIES 1-1/4 PULG How many 3-Foot 6-Inch pieces can you cut from one 25-foot board? KEYSTROKE DISPLA Y o o 0.
P OCKET R EFERENCE G UIDE — 18 Square Area Find the Area of a square room with sides measuring 15 Feet 8-1/2 Inches: KEYSTROKE DISPLA Y o o 0. 1 5 f 8 i 1 / 2 Ç √ (x 2 ) 246.
P OCKET R EFERENCE G UIDE — 19 Entering Square and Cubic and Adding a W aste Allowance Add a 10% waste allowance to 55 Square Feet. Then add a 20% waste allowance to 150 Cubic Feet: KEYSTROKE DISPLA Y o o 0. 5 5 f f + 1 0 % 60.5 PIES CUAD 1 5 0 f f f + 2 0 % 180.
P OCKET R EFERENCE G UIDE — 20 Weight per V olume Convert 20 Cubic Y ards of concrete to T ons, Pounds, Metric T ons and Kilograms, if concrete weighs 1.5 T ons per Cubic Y ard (default value): KEYSTROKE DISPLA Y o o 0. 2 0 y y y 20 YD CUB Ç w 30. Ton * w 60000.
P OCKET R EFERENCE G UIDE — 21 Using the Memory Whenever the μ key is pressed, the displayed value will be added to the Memory . Other memory functions: FUNCTION KEYSTROKES Add to Memory μ Subtrac.
P OCKET R EFERENCE G UIDE — 22 Board Feet and Cost Find the total Board Feet for the following boards: 2x4x16, 2x10x18 and 2x12x20. What is the total cost at $275 per Mbm*? *Per thousand Board Foot measure KEYSTROKE DISPLA Y o o 0. 2 x 4 x 1 6 b μ P-MD 10.
P OCKET R EFERENCE G UIDE — 23 Baluster Spacing Y ou are going to install a handrail at the top of a balcony . Y our total span is 156 Inches and you would like the space between the balusters to be about 4 Inches. If each baluster is 1-1/2 Inches wide, what is the exact spacing between each baluster? KEYSTROKE DISPLA Y 1.
P OCKET R EFERENCE G UIDE — 24 Circle Area and Circumference Find the Area and Circumference of a Circle with a Diameter of 25 Inches: KEYSTROKE DISPLA Y o o 0.
P OCKET R EFERENCE G UIDE — 25 Concrete V olume for Driveway Calculate the Cubic Y ards of concrete required to pour a driveway that meas- ures: 45 Feet 5 Inches long x 13 Feet 6 Inches wide x 5 Inches deep. If concrete is $65 per Cubic Y ard, what will it cost? KEYSTROKE DISPLA Y o o 0.
P OCKET R EFERENCE G UIDE — 26 Complex Concrete V olume Y ou’re going to pour an odd-shaped patio 4-1/2 Inches deep with the dimensions shown below . First, calculate the total Area (by dividing the drawing into three individual rectangles) and then determine the total Y ards of concrete required for this job.
P OCKET R EFERENCE G UIDE — 27 KEYSTROKE DISPLA Y 1. Find Area of Part “A” and add to Memory: o o 0. 3 8 f 2 i – 4 f 2 i = 34 PIES 0 PULG x 2 7 f = 918. PIES CUAD μ M+ 918. PIES CUAD 2. Find Area of Part “B” and add to Memory: 4 f 2 i 4 PIES 2 PULG x 8 f 6 i = 35.
P OCKET R EFERENCE G UIDE — 28 RIGHT ANGLE / FRAMING The top row of keys provide you with built-in solutions to Right T riangles. The solutions are available in any of the linear dimensions offered on the calculator . Thus, you can solve Right T riangles directly in Feet and Inches, Decimal Feet, Meters, etc.
P OCKET R EFERENCE G UIDE — 29 Squaring-Up a Foundation Square-Up 15 Feet 6 Inch (Run) x 10 Feet 2 Inch (Rise): KEYSTROKE DISPLA Y o o 0. 1 5 f 6 i R RECR 15 PIES 6 PULG 1 0 f 2 i r AL T 10 PIES 2 PULG d DIAG 18 PIES 6-7/16 PULG Pitch — Converting Roof Angle Find the % Grade, Pitch Ratio/Slope and Pitch in Inches if the roof angle is 30.
P OCKET R EFERENCE G UIDE — 30 Converting Slope Find the Pitch in Inches, Pitch Degrees, and Percent Grade if the Pitch Ratio/Slope is 0.625: KEYSTROKE DISPLA Y o o 0.
P OCKET R EFERENCE G UIDE — 31 Regular Hip/V alley and Jack Rafters A roof ’s Pitch is 9/12 and half the total Span is 6 Feet. Find the lengths of the Common, Hip/V alley and Jack rafters (Jack rafters at 16 Inch On-Center spacing): KEYSTROKE DISPLA Y 1.
P OCKET R EFERENCE G UIDE — 32 (Cont’d) KEYSTROKE DISPLA Y 2. Find the Hip/V alley rafter and Jack rafter lengths: H LIMA 9 PIES 7-1/4 PULG j CCEC 16 PULG * j CC 1 5 PIES 10 PULG j CC 2 4 PIES 2 PULG j CC 3 2 PIES 6 PULG j CC 4 0 PIES 10 PULG j CC 5 0 PIES 0 PULG *Uses standard (default) 16-Inch On-Center .
P OCKET R EFERENCE G UIDE — 33 Irregular Hip/V alley Y ou’re working with a 7/12 Pitch and half of your overall Span is 15 Feet 7 Inches. The Irregular Pitch is 8/12. Find the Common rafter length, Irregular Hip/V alley and Jack rafter lengths. KEYSTROKE DISPLA Y 1.
P OCKET R EFERENCE G UIDE — 34 Rake-W all — No Base Find each stud size in a Rake-Wall with a peak of 3 Feet 6 Inches and a length of 6 Feet. Use 16 Inches as your spacing (default): KEYSTROKE DISPLA Y 1. Enter Rise and Run: o o 0. 3 f 6 i r AL T 3 PIES 6 PULG 6 f R RECR 6 PIES 0 PULG 2.
P OCKET R EFERENCE G UIDE — 35 ST AIRS Stairs — Given Rise and Run Y ou’re going to build a stairway that has a Floor-to-Floor height of 10 Feet 1 Inch, a Run of 12 Feet 5 Inches, and a desired Riser Height of 7-1/2 Inches (default). Find the stair values: KEYSTROKE DISPLA Y 1.
P OCKET R EFERENCE G UIDE — 36 (Cont’d) KEYSTROKE DISPLA Y 2. Recall stored 7-1/2 Inch desired Riser Height and find stair values: ® s C-AL 7-1/2 PULG s C-AL 7-9/16 PULG * s CHUE 16. s C+/– 0 PULG s H-AN 9-15/16 PULG * s HUE 15. s H+/– 0-1/16 PULG s LRGO 15 PIES 7-5/16 PULG s INCL 37.
P OCKET R EFERENCE G UIDE — 37 Stairs — Given Only the Floor-to-Floor Rise; Entering Other Than 7-1/2 Inch Desired Riser Height Find stair values if the Floor-to-Floor Rise is 12 Feet 6 Inches, and the desired Riser Height is 8 Inches: KEYSTROKE DISPLA Y 1.
P OCKET R EFERENCE G UIDE — 38 Setting Fractional Resolution Fractional resolution is pemanently set via the Preference Settings (see Preference Settings section for instructions).
P OCKET R EFERENCE G UIDE — 39 Default Settings After a Clear All ( Ç x ), your calculator will return to the following settings: STORED V ALUES DEFAUL T V ALUE Stair Riser Height 7-1/2 pulgadas Stair T read Width 10 pulgadas On-Center Spacing 16 pulgadas Weight per V olume 1.
P OCKET R EFERENCE G UIDE — 40 Accuracy/Errors Accuracy/Display Capacity — Y ou may enter or calculate values up to 19,999,999.99. Each calculation is carried out internally to twelve digits. Errors — When an incorrect entry is made, or the answer is beyond the range of the calculator , it will display the word “ERROR.
P OCKET R EFERENCE G UIDE — 41 Battery This model uses one (1) CR2016 battery (included). Should your calculator display become very dim or erratic, replace the battery . Note : Please use caution when disposing of your old batteries, as they contain hazardous chemicals.
P OCKET R EFERENCE G UIDE — 42 AREA AND VOLUME FORMULAS Area Formulas.
P OCKET R EFERENCE G UIDE — 43 V olume Formulas.
P OCKET R EFERENCE G UIDE — 44 REP AIR AND RETURN W arranty , Repair and Return Information Return Guidelines 1. Please read the Warranty in this User's Guide to determine if your Calculated Industries product remains under warranty before calling or returning any device for evaluation or repairs.
P OCKET R EFERENCE G UIDE — 45 W ARRANTY W arranty Repair Service – U.S.A. Calculated Industries (“CI”) warrants this product against defects in materials and workmanship for a period of one (1) year from the date of original consumer purchase in the U.
P OCKET R EFERENCE G UIDE — 46 Disclaimer CI MAKES NO WARRANTY OR REPRESENTA TION, EITHER EXPRESS OR IMPLIED, WITH RESPECT T O THE PRODUCT’S QUALITY , PERFORMANCE, MER- CHANT ABILITY , OR FITNESS FOR A P ARTICULAR PURPOSE.
P OCKET R EFERENCE G UIDE — 47 FCC CLASS B This equipment has been certified to com- ply with the limits for a Class B computing device, pursuant to Subpart J of Part 15 of FCC rules.
This equipment has been certified to comply with the limits for a Class B computing device, pursuant to Subpart J of Part 15 of FCC rules. Software copyrighted and licensed to Calculated Industries, Inc. by Construction Master T echnologies, LLC, 2007.
Een belangrijk punt na aankoop van elk apparaat Calculated Industries 4054 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Calculated Industries 4054 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Calculated Industries 4054 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Calculated Industries 4054 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Calculated Industries 4054 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Calculated Industries 4054 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Calculated Industries 4054 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Calculated Industries 4054 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
