Gebruiksaanwijzing /service van het product AL2810 van de fabrikant Campbell Hausfeld
Ga naar pagina of 32
Airless Paint Systems Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
2 Operating Instructions and Parts Manual Airless Paint Systems Description Airless paint sprayers are capable of spraying a wide variety of latex, oil- based, and alkyd paints, as well as stains, preservatives and other non- abrasive finishes.
Airless Paint Systems 3 Operating Instructions and Parts Manual General Safety Information (Cont.) 4. Do not smoke or eat when spraying paint, insecticides, or other flammable substances. 5. Always work in a clean environment. To avoid injury and damage to the workpiece, do not aim the spray gun at any dust or debris.
4 Operating Instructions and Parts Manual Airless Paint Systems General Safety Information (Cont.) ● Paints and solvents containing HALOGENATED HYDROCARBONS can react explosively with aluminum. Do not use halogenated hydrocarbons with this equipment.
Airless Paint Systems 5 Operating Instructions and Parts Manual Pr e-Operation (Cont.) 5. Open the prime valve to the open - "Priming Position". This will allow for an easy start. Refer to Figure 1 on page 4. 6. Turn the engine ON/OFF switch to ON.
6 Operating Instructions and Parts Manual Airless Paint Systems www.chpower.com Pr e-Operation (Cont.) flow rate or capacity the sprayer can accommodate.
7 Airless Paint Systems Operating Instructions and Parts Manual www.chpower.com Operation STARTING UP 1. Learn the functions of the controls (see “How to Spray / Important Components” for more information). 2. Prepare the Material a. Prepare the material according to material manufacturer's recommendations.
8 Operating Instructions and Parts Manual Airless Paint Systems www.chpower.com Operation (Cont.) d. For long term shutdown or storage, refer to page 4. Be sure to relieve pressure in the pump after filling with mineral spirits. SPRAY TECHNIQUE Good Spray Gun Technique is at the core of any spray paint operation.
9 Airless Paint Systems Operating Instructions and Parts Manual www.chpower.com Electrical System (Cont.) and remove knob. 5. Using a 1/2” nut driver or 1/2” deep socket, remove nut from pressure control shaft. This will allow removal of electrical control board from frame.
10 Operating Instructions and Parts Manual Airless Paint Systems www.chpower.com Service FLUID PUMP FLUID PUMP DISCONNECT 1. Flush out the material you are spraying, if possible. 2. Follow the Pressure Relief Procedure on page 3. Stop the pump in the middle of down stroke.
11 Airless Paint Systems Operating Instructions and Parts Manual www.chpower.com halves and remove both coupling halves. This will disconnect piston rod from connecting rod and gearbox assembly. 3. Screw the suction nut off the pump and remove inlet valve assembly.
12 Operating Instructions and Parts Manual Airless Paint Systems www.chpower.com Service (Cont.) Disconnect hose from fluid section. 5. Disconnect and remove fluid section from gearbox, including Connecting Rod Assy. (See"Fluid Pump Disconnect, page 10) 6.
13 Airless Paint Systems Operating Instructions and Parts Manual www.chpower.com Maintenance (Cont.) Inspect the packing nut daily. If seepage of paint into the packing nut and/or movement of the piston upward is found (while not spraying), the packing nut should be tightened enough to stop leakage only, but not any tighter.
Operating Instructions and Parts Manual Airless Paint Systems 14 www.chpower.com Coarse spray Excessive fogging (overspray) Pattern too wide Pattern too narrow Too much material Too little material Th.
15 Airless Paint Systems Operating Instructions and Parts Manual www.chpower.com AL2810 There is splitting from the gun. Paint leaks into the wet cup. Engine operates, but paint pump does not cycle En.
Operating Instructions and Parts Manual 16 www.chpower.com AL2810 STEP 1: Ensure that the pressure control knob is in the maximum (fully clockwise) position.
Operating Instructions and Parts Manual 17 www.chpower.com AL2810 Notes.
18 For Replacement Parts, Call 1-800-626-4401 See Figures 10 & 11 on pages 10 & 11 for mor e Part Numbers in Diagrams Please provide following information: -Model number -Serial number (if any) -Part descriptions and number as shown in parts list Address parts correspondence to: Campbell Hausfeld 100 Production Drive Harrison, OH 45030 U.
19 Operating Instructions and Parts Manual www.chpower.com AL2810 Ref. No. Description Part Number Qty. 1 007 Gun with swivel (Optional) 120-201XL 1 2 50’ x 1/4” Hose (Optional) 100-011 1 3 50’ .
20 Operating Instructions and Parts Manual www.chpower.com AL2810 Power Unit Assembly Part No. 301-530.
21 Operating Instructions and Parts Manual www.chpower.com AL2810 301-530 Ref. No. Description Part Number Qty. 1 Sleeve bearing 301-047 1 2 Shield front 301-189 1 3 Coupling set assembly 189-046A 1 4.
22 Operating Instructions and Parts Manual www.chpower.com AL2810 Frame Assembly Part No. 301-515 13 11 1 12 2 3 4 10 9 8 7 6 5.
23 Operating Instructions and Parts Manual www.chpower.com AL2810 301-515 Ref. No. Description Part Number Qty. 1 Frame weldment 301-510 1 2 Axle 5/8 x 21.81 188-367 1 3 Spacer 5/8 ID 113-031 2 4 Wheel 13 x 500-6T 301-165 2 5 Set collar 5/8 ID 143-029 2 6 Centerlock nut 5/16-18 100-317 2 7 Rubber foot 163-008A 2 8 Spacer .
24 Operating Instructions and Parts Manual www.chpower.com AL2810 7 8 9 Engine Assembly Part No. 301-524 2 3 4 5 6 1 301-524 Ref. No. Description Part Number Qty.
25 Operating Instructions and Parts Manual www.chpower.com AL2810 Clutch Replacement Parts Ref. No. Description Part Number Qty. 1 Cog belt 301-231 1 2 Clutch 301-264 1 3 Screw 305-088 1 4 Shoulder sc.
26 Operating Instructions and Parts Manual www.chpower.com AL2810 Clutch Assembly Ref. No. Description Part Number Qty. 1 Screw-Differential 112-041 1 2 Coupling nut assembly 112-054 1 3 Spacer 301-41.
27 Operating Instructions and Parts Manual www.chpower.com AL2810 Ball Valve Part No. 100-119 100-119 Ref. No. Description Part Number Qty. 1 Handle 100-162 1 2 Screw 100-163 1 3 Ball 100-164 1 * Repa.
28 Operating Instructions and Parts Manual www.chpower.com AL2810 Manifold Filter Part No. 111-200-99 111-200-99 Ref. No. Description Part Number Qty. 1 Base* 111-202 1 2 Spring* 301-356 1 3 O-ring* 1.
29 Operating Instructions and Parts Manual www.chpower.com AL2810 Suction Assembly - 5 Gallon Part No. 301-090-99 Suction Assembly - 55 Gallon Part No.
30 Operating Instructions and Parts Manual www.chpower.com AL2810 Notes.
31 Operating Instructions and Parts Manual www.chpower.com AL2810 Notes.
32 Operating Instructions and Parts Manual www.chpower.com AL2810 Limited Warranty 1. DURATION: From the date of purchase by the original purchaser as follows: Standard Duty Paint Application Systems and all Paint Application Accessories - 1 year, Serious Duty Paint Application Systems - 3 years, Extreme Duty Paint Application Systems - 5 years.
Een belangrijk punt na aankoop van elk apparaat Campbell Hausfeld AL2810 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Campbell Hausfeld AL2810 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Campbell Hausfeld AL2810 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Campbell Hausfeld AL2810 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Campbell Hausfeld AL2810 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Campbell Hausfeld AL2810 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Campbell Hausfeld AL2810 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Campbell Hausfeld AL2810 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
