Gebruiksaanwijzing /service van het product IMAGEFORMULA DR-X10C van de fabrikant Canon
Ga naar pagina of 67
Please read this man ual before using the scanner. After you finish reading this ma nual, keep it in a safe place for future reference. Reference Guide.
i READ CAREFULL Y BEFORE OPENING THE SEALED DISK P ACKA GE CANON SOFTW ARE LICENSE A GREEMENT IMPOR T ANT -READ THIS A GREEMENT BEFORE OPENING THE SEALED DISK P A CKA GE! BY OPENING THE SEALED DISK P A CKA GE, Y OU ARE DEEMED TO A GREE TO BE BOUND BY THIS A GREEMENT .
ii NEITHER CANON, CANON’S AFFI LIA TE, TH EIR DISTRIBUTOR NOR DEALER IS LIABLE FOR ANY LOSS OR D AMA GE INCLUDING CO NSEQUENTIAL OR INCIDENT AL LOSS OR D AMA GE SUCH AS LOSS OF PR OFITS, EXPENSE OR INCONVENIEN CE, WHA TSOEVER CA U SED BY OR ARISING OUT OF THE SOFTW ARE, ACCOMP ANYING DOCUMENT A TIO N OR THE USE THER EOF .
iii FCC REGULATIONS (For 120 V model) Document Scanner, Model M11063 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditi ons: (1) This device may not cause harmful inte rference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
iv European Union (and EEA) only. This symbol indicates that this product is n ot to be disposed of with your household waste, according to the WEEE Directive (2002/96/EC) and your national law. This product should be handed over to a designated collecti on point, e.
v Introduction Thank you for purchasing the Canon imageFORMULA DR-X10C Docume nt Scanner. Please read th is and the following manuals thoroughly before using the scanner to become acquainted with its capabilities and make th e most of its many functions.
vi Symbols Used in This Manual The following symbols are used in this manual to explain procedures, restri ctions, handling precau tions, and instructions that should be observed for safety. WARNING Indicates a wa rning c oncerning operations that may lead to death or injury to persons if not performed correctly.
vii Table of Contents Introduction ..... .............. ................. .............. ........... v Manuals fo r the Scanner ............. ........... ............. ..... v Symbols Used in This Manual ............. ............. ....... vi How This Manual i s Organized.
Chapter 1 Before You Start Using the Scanner 1. Important Safety I nstruct ions .......... ................. ... 2 Installation Location ............... .............. .......... .......... 2 Power ...... ............. ........... ............. ......
2 1. Important Safety Instructions To ensure the safe operation of this sc anner, be sure to read the safety warnings and pr ecautions described below. Installation Location The performance of this sc anner is affected by the environment in which it is install ed.
3 1 Before Y ou Star t Using t he Scanner ● Do not pull directly on the power cord. When disconnecting the power cord, grasp the plu g and remove it from the outlet. ● Keep the area around the power plug clea r of objects so that the power cord can be disconnected easily in an emergen cy.
4 ■ Some parts can only be cleaned when the power is turned ON. In these cases, be careful to avoid electric shock. ■ Clean the scanner using a slightly dampene d cloth which has been well wrung ou t. Never use alcohol, benzene, paint thi nner, or any other flammable substances.
5 1 Before Y ou Star t Using t he Scanner ■ Do not wear loose clothing or jewelry that ma y get caught in the scanner wh ile you are using it. This may result in personal injury. Be extra careful of neckties and long hair. If anythi ng becomes caught in the scanner, immediately discon nect the power cord to stop the scanner.
6 2. Features The main features of th e DR-X10C are described below. Refer to the User Manual for detailed inf ormation. Scanner Features ● Fast Document Feeding The scanner can scan up to 1 00 document sheets per minute of LTR/A4-size pape r in black and white, grayscale, and co lor scanning modes.
7 1 Before Y ou Star t Using t he Scanner Detection Functions ● Auto Image Type Detection The scanner automati cally detects whether documents are in black and white or color. ● Auto Paper Size Detection The document page size is detected before scanning.
8 ● Dropout and Color En hancement Functions The scanner is equipped with drop-out and enhancement functions that enable you to specify one color (red, blue, or green) to be omitted (dropped out) or enhanced when scanning, respectively.
9 1 Before Y ou Star t Using t he Scanner Other Functions ● Rapid Recovery System When this function is activat ed and a sensor detects a misfeed due to a paper jam or double feed, wh ich causes fee.
10 3. Names and Functions of Parts The names and functions of the DR-X10C parts are shown below. Front View, Feeder Inlet, and Ejec t Outlet a Document Eject Tray Scanned documents are output here. b Document Feed Tray Load documents to be scanned. c Power Switch Turns the scanner ON and OFF.
11 1 Before Y ou Star t Using t he Scanner Rear View a USB Connector (Type B) Connect the supplied USB cable here. b SCSI Connector (50-pin half-pitch D-sub receptacle) Connect the SCSI cable here. c DIP Switch (SCSI ID) Selects the scanner’s SCSI ID.
12.
Chapter 2 Basic Operation 1. Turning the Po wer ON and OFF ................ ....... 14 About the P ower Switch ....... ............. ............. ........ 14 2. Documents .................. ................. .............. ....... 15 Acceptable Docum ents .
14 1. Turning the Powe r ON and OFF Use the power switch to turn the DR-X10C scanner ON and OFF, or if you are using a USB connection, you can set the USB-linked power switch. CAUTION • After tur ning the scan ner OFF, wait at least ten s econds before turning it b ack ON.
15 2 Basic Operation 2. Documents The DR-X10C scanner can scan documents rang ing in size from business cards and checks to 11" × 17"/A3 size. The size and type of paper that can be fed depends on the feeding method. Acceptable Documents The scanner ca n feed the following document sizes.
16 • To scan bound mul ti-page doc uments such as inv oice booklets, place the boun d edge again st the feeder inlet and scan by manual feeding. • To use the Long Document Mode, f eed document pag es manually, one a fter anothe r.
17 2 Basic Operation 3. Document Feed and Eject Trays Before scanning, prepare the Do cument Feed and Eject Trays for th e desired paper size. Preparing the Document Feed Tray ■ Opening the Document Feed Tray When the scanner is turned ON, the Document Feed Tray opens automatically and m oves to the specified home position height.
18 ■ Document Guides Unlock the document guides by gently pr essing both sides of either guide ( a ), and slidin g the document guides to match the width of your do cument ( b ). Hint The positio ns of the left and right do cument guide s can also be locked in dependently for off-cent er loading.
19 2 Basic Operation 2. Load your documents against the left feed guide. 3. Lock the left document guide ( a ) by pulling out th e lock lever, then slide the righ t document guide to the right edge of your documents ( b ). 4. Lock the right document guide ( a ), and unlock the left document guide ( b ).
20 3. Slide the rig ht document gui de all the way to th e right. 4. Unlock the left document guide. Preparing the Document Eject Tray The Eject Tray incl udes two Document Eject Guides, the Eject Tray Extension and Eject Paper Stopper, to be adjusted to match the length of your documents.
21 2 Basic Operation ■ Document Eject Tray Extension Pull out the tray extension to match the le ngth of your do cument. ■ Eject Paper Stoppers Raise the appropriate Eject Paper Stopper to stop ejected documents from spilling out of the eject tray.
22 4. Document Feeding Methods Two document feeding methods are available: Continuous Feeding, which feeds docume nts automatically fro m the document tray by the pickup roller; and Manual Feeding, which requires one document at a time to be positioned manually for transport by the feed roller, while the pi ckup roller is disabled.
23 2 Basic Operation Hint • The [Byp ass Mode] ke y is link ed to the [Manual Feed ing] Fee d Option sett ing of the ISI S/TWAIN driver. • When the [Bypass Mode] key on th e control panel is pr essed or the [Ma nual Feedin g] Feed Op tion is sel ected, the [Bypass Mode] key lig hts and th e Document Fe ed Tray rise s.
24 5. Scanning Scanning operations can be controll ed by a scanning application progr am such as the CapturePerfect 3.0 software included with t he scanner, or directly from the control panel of the DR -X10C, using the Job Function. This section describes the J ob Function and provides an overv iew of CapturePerfect 3.
25 2 Basic Operation CapturePerfect 3.0 CapturePerfect 3.0 is an ISIS-compatible app lication developed for Canon document scanners. CapturePerfect 3.0 includes the following modes. Select the desired scan mode from the Scan menu to perform scan ning.
26 Scan To Presentation This mode is convenient when a compact scanner is used in an environment such as a conference hall, where it is connected to a large display or projector. By setting CapturePerfect for full-screen display before scanning, scanned images are displayed at ful l size on the screen.
27 2 Basic Operation 4. Set the [Default Page Size]. IMPORTANT If you select [Default] in the ISIS dr iver prope rties dial og box, that setting is ap plied here. 5. Click [OK] to finish scanner selection. 6. From the [Scan] menu, select [Scanner Setting].
28 10. Place your document and click [Save] to start scanning. IMPORTANT You must loa d your docume nts as desc ribed belo w, depending on the spec ified Feed Option setting. • If the [Sta ndard Feeding ] Feed Option is enabled, l oad your documents be fore scann ing.
29 2 Basic Operation 6. Clearing a Paper Jam or Double Feed Error If a paper jam or double feed occurs during scanning, a paper jam message appears on the PC and on the scanner’s display panel.
30 IMPORTANT The Rapid Re covery Syst em setti ng in the ISIS/TWAIN d river causes the fol lowing proc ess to occur af ter a paper jam. • When the Rapid Recov ery System is disabled , images scanned befo re the pape r jam occurs are saved as file s, scanning fi nishes, finis hed and an erro r message is disp layed.
31 2 Basic Operation • When the Rapi d Recovery Sy stem is enabled, scanning pauses when a doub le feed is detected, a nd the follo wing erro r message is displayed.
32.
Chapter 3 Maintenance 1. Regular Maintenance ................... ................. .... 34 Cleaning the Scanner. ............. ........... ............. ....... 34 Cleaning the Glass and Ro llers............... ............. .. 35 Opening and Closing the Upper Un it .
34 1. Regular Maintenance To maintain scanning quality, routinely clean the scanner as described below. CAUTION • Do not use spra y cleaners to clean the scann er. Precisi on mechanis ms may get wet and malf unction. • Never use pa int thinne r, alcohol, or other organ ic solven ts to clean th e scanner.
35 3 Maintenance Cleaning the Glass and Rollers If scanned images contain spot s or documents become dirty after scanning, the scanning gla ss or transport rollers inside the scanner may be dirty. The locations of the main gla s s and rollers are as follows.
36 Hint An error messa ge appears on t he display pan el if the up per unit is open (r aised). Cleaning Rollers with a Cleaning Sheet Rollers in th e transport pat h are cleaned using the Cleaning Mode of the User Mode, using a cleaning sheet. Hint • Each cleani ng sheet is us ed several tim es to clean one si de of the rollers.
37 3 Maintenance 6. Insert the cleaning sheet adhesive-side up into the feed inlet. The cleaning sheet feeds through the scanner, and the Cleaning Mode exits. 7. Inspect the cleaning shee t for dust. 8. Repeat steps 3 to 6 several times using the same cleaning sheet to clea n the same side of the rol lers.
38 3. Wipe any dust of f the scanning gla ss with a clean, dry cloth. 4. Press the Stop key to turn off the lamp. 5. Carefully lower the upper unit ( a ).
39 3 Maintenance 3. Clean the black and white surfaces of the rollers by wiping horizontally with a moistened, w rung-out cloth. IMPORTANT When cleaning , be careful not to bend th e sheet ove r the roller . The locati on of th e sheet fo r the lower platen roller is in fron t of the roller.
40 3. Lift the pickup roller mounting le ver, and remove the roller. 4. Pull the feed roller lock lever down ( a ) and move it to the right ( b ) to unlock the feed roller. 5. Remove the feed roller. 6. Use a moistened, well wrung-out cloth to wipe o ff any dust from the rollers.
41 3 Maintenance 3. Push the feed roller lock lever up ( a ) and move it to the left ( b ) to lock the feed roller in place. 4. Push the roller cover up until it clicks in to place. IMPORTANT When opening an d closing the roller cover , be careful not to touch the gl ass (stapl e detectio n window).
42 3. Push the roller lock lever up ( a ) and move it to the left ( b ) to unlock the roller. 4. Remove the retard roller. 5. Use a moistened, well wrung-out cloth to wipe off any dirt from the roller. ■ Reinstalling the Retard Roller 1. Set the retard roller into place in the scanner.
43 3 Maintenance 4. Replace the roller cover. 5. Push the front of the roller co ver in until it clicks into place. 6. Carefully lower the upper unit ( a ).
44 2. Replacing the Transport Rollers As the rollers sta rt to wear out, fe eding quality declines, and doc ument feed errors, such as pa per jams, become more likely. If document feed er rors continue to occur after c leaning the rollers, purcha se the Roller Replac ement Kit and replace t he trans port rollers (pickup, feed, and retard rollers).
Chapter 4 Practical Examples 1. Messages... ................. .............. .............. .......... 46 Status Display ........... ............. .............. .......... ........ 46 Error Messages ............ .......... .............. ............
46 1. Messages There are two types of display panel messages: “s tatus indic ator messages” and “ error messages” th at appear when t he scanner encounters a problem. Status Display The following messages appear on the display panel to indicate the scanne r’s operating state: ■ Counting.
47 4 Practical Examples Error Messages When one of the following me ssages appears on the display panel, an error has occurred in the scanner. Follow the indicated procedure to resolve the error . ■ Check Imprinter Error Code: H001 Problem: No ink cartridge is install ed in the post - imprinter.
48 ■ Skew Detected Error Code : J018 Problem: A skewed document page contacted the wall of the transport path. Solution: Remove and repositio n th e document page. ■ Double Feed Error Code : D002 Problem: A double feed was detected by the document length.
49 4 Practical Examples 2. Troubleshooting This section describes the problems that may occur during use of the scanner and how to solve them. Trouble Categories The following trouble ca tegories are addressed: • The Scanner Does Not Turn ON (See p.
50 ■ The Scanner Is Not Recognized (Con necting via SCSI) If the scanner’s SCSI connec tion is not recognized , first confirm the following: ✔ Are the scanner and PC conne cted correctly using t.
51 4 Practical Examples If this does not solve the pr oblem, consider the following possible causes: Cause Other applications are running in the background on your PC. Solution Quit all other appl ications that are running. Cause Resident applications, such as anti-virus software, are draining me mory resources.
52 Problem Text or images from the back side of your document appear in the scanned image. Cause Brightness may be set too low. Solution Increase the Brightne ss setting. Or, enable the [Prevent Bleed Through/Remove Background] setting. Cause The paper is too thin.
Chapter 5 Appendix 1. Specifications ................. ................. .............. .... 54 Unit Specif ications ........... .......... ............. ............. ... 54 Consumable s ............ ........... ............. ............. ........ 56 External Dimen sions .
54 1. Specifications Unit Specifications Type Desktop sheet-fed scanner Scannable Document Requi rements Width: 2" to 12.01" (50.8 mm to 305 mm) Length: 2.76" to 17.01" (70 to mm 432 mm) Weight: Page Separation Feeding: 14 lb to 32 lb bond (52 g/m 2 to 128 g/m 2 ) (0.
55 5 Appendix Scanning Speed (LTR/A4 landscap e) Black and White 200 dpi Simplex 130 pages/min. Duplex 260 images/min. 300 dpi Simplex 130 pages/min. Duplex 256 images/min. 400 dpi Simplex 82 pages/min. Duplex 82 imag es/min. 600 dpi (speed priority) Simplex 80 pages/min.
56 Consumables Roller Replacement Kit (Product Code : 2418B001) Replacement kit for transport rollers (pick-up roller, feed rollers, and retard roller). (See “Replacing the Transport Rollers” on p. 44.) IMPORTANT • Rollers are consu mable parts.
57 5 Appendix External Dimensions 33.90" ( 861 mm) 21.10" (5 36 mm) 22.17" (563 mm) 14.77" ( 375 mm) 17.01" (432 mm) 20.79" (5 28 mm) 5.
58 2. Index C CapturePerfect 3.0 . ........... ............ ........... ........... ........... .25 Cleaning feed roller ......... ........... ............ ........ ............ ........... ...39 glass ........ ............ ........ ............ .....
CANON ELECTRONICS INC. 1248, SHIMOKAGEMORI, CHI CHIBU-SHI, SAITAMA 369-1892 , JAPAN CANON U.S.A. INC. ONE CANON PLAZA, LAKE SUCCESS, N.Y. 110 42, U.S.A. CANON CANADA INC. 6390 DIXIE ROAD, MISSISSA UGA, ONTARIO L5T 1P7, CANADA CANON EUROPA N.V. BOVENKERKERWEG 59-61, P.
Een belangrijk punt na aankoop van elk apparaat Canon IMAGEFORMULA DR-X10C (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Canon IMAGEFORMULA DR-X10C heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Canon IMAGEFORMULA DR-X10C vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Canon IMAGEFORMULA DR-X10C leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Canon IMAGEFORMULA DR-X10C krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Canon IMAGEFORMULA DR-X10C bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Canon IMAGEFORMULA DR-X10C kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Canon IMAGEFORMULA DR-X10C . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
