Gebruiksaanwijzing /service van het product C-2003G-IT van de fabrikant Cecilware
Ga naar pagina of 19
CENTURY 2000-IT, COFFEE BREWING EQUIPMENT Cecilware sells value... Worldwide 43 -05 20th Avenue, Long Island City, NY 11105 TEL: 718-932-1414 FAX: 718-932-7860 MODELS C-2003G-IT C-2003RG-IT C-2003LG-I.
2 SPECIFICATIONS ELECTRICAL SPECIFICATIONS MODEL NO. C-2003G-IT C-2003RG-IT C-2003LG-IT Volts 120 120 120 Watts 1,800 1,800 1,800 Amps 15 15 15 Wall Outlet (Receptacle) 5-15R 5-15R 5-15R All Brew Centers are single phase with 2 wires plus a ground with cord and plug, except Eport 220V, 1 PH, 50 cycles (UROPEAN).
3 FEATURES AND BENEFITS OF THE DIGITAL, MEMBRANE CONTROL TOUCH PAD BREWER 1. 100% Solid State Control for improved reliability. 2. Modular design and reduced component count for ease of service. 3. Optional Low Water Temperature Lockout to prevent dispensing at water temperatures below an adjustable threshold.
4 INSTALLATION AND OPERATING INSTRUCTIONS Warranty is void if the Brewer is connected to any Voltage other than the Voltage specified on the data label of the Brewer. UNPACKING AND INSPECTION Carefully unpack the Brewer by cutting the straps and lifting the carton off the Brewer.
5 NG34A -E CAU TI O N HOT WATER D: 1-M ilt Lab els & L og osT ech n o c op y .t if PROGRAMMING INSTRUCTIONS The following is a Functional Description of the Single Station Brewer : Modes of Operation - Overview Initialization Mode – This mode is only active during the fi rst few seconds after a “power-on” or system reset.
6 MODES OF OPERATION – DESCRIPTIONS Initialization Mode: The following screen signifies the presence of this mode: CECILWARE &&&&& REV #.# Description – This mode is active only during the first few seconds after “power-on”.
7 Brewing State BREWING DDD K MM:SS HH:MMP Description – This screen is displayed when a Brew Cycl e is in progress. The time remaining in the Brew Cycle is displayed in the lower left-hand corner of the screen (depicted as “MM:SS”). The Brew Key LED will blink in this state.
8 SERVICE MODE Description – The main function of Service Mode is to gi ve qualified personnel the ability to configure the system to meet the requirements of each installation.
9 INFUSION TIME - OPTIONAL INFUSION TIME ## SECONDS Description – The Infusion Time is the amount of time that the system will dispense (infuse) hot water into the grinds during the Pre-Infusion process.
10 WARMER TIMER WARMER TIMER ON/OFF Description – The Warmer Timer feature allows the user to set the maximum length of time a brew remains fresh while being warmed. Once the Warmer Timer has expired an alarm is generated. An alarm consists of a blinking warmer LED and (opt ionally) the audible alarm (buzzer) sounding.
11 ADJUST SECONDS ADJUST SECONDS DAY HH:MM:## Description – The Adjust Seconds function allows the user to adjust (set) the systems Real-Time-Clock Seconds placeholder. ADJUST MINUTES ADJUST MINUTES DAY HH:##:SS Description – The Adjust Minutes function allows th e user to adjust (set) the systems Real-Time-Clock Minutes placeholder.
12 ERROR MODE Description – The main function of Error Mode is report any system malfunctions and to disable the unit The system must be “powered down” usi ng the Power Key located on the membrane keypad to reset any reported error.
13 C-2003G-IT FRONT OPEN VIEW 1 2 3 4 5 18 17 16 15 13 12 11 6 7 8 9 10 14.
14 TOP CABIN OPEN VIEW 24 23 29 28 25 26 19 20 21 22 32 31 30 27.
15 PARTS IDENTIFICATION FOR C-2003G-IT, C-2003LG-IT, C-2003RG-IT ITE M SPARE PARTS P/N QTY DESCRIPTION 1 * NG34A 1 TOUCH PAD LABEL: C-2003G-IT, C-2003LG-IT, C-2003RG-IT 2 * L616A 1 THERMISTER PROBE 3 * L615A P182A K624A P301A 1 2 1 2 TRIAC 25 AMPS SCREW F/ TRIAC HEATSINK, F/TRIAC, COPPER WINGED NUT F/ HEATSINK 4 M483A 1 SILICONE HOSE ( .
16 TROUBLESHOOTING GUIDE WARNING: To reduce the risk of electrical shock unplug the dispenser power cord before repairing or replacing any internal components of the unit.. Before any attempt to replace a component be sure to check all electrical connections for proper contact PROBLEM PROBABLE CAUSE REMEDY 1.
17 SPECIAL COMPONENTS TEST AND ADJUSTMENTS 1) WATER INLET VALVE (SOLENOID) TEST ( Located inside bottom cabin ) Turn power off from touchpad. If the water level rises inside the tank, and shoots out of the overflow, the Water Inlet Valve is le aking. Disconnect wires from the Water Inlet Valve coil and connect a 2 wire line cord to the terminals.
18 5) CHECK DISPENSE VALVES FOR LIME BUILD-UP ( Located inside top cabin ) Drain The Water Tank To Just Below The Level Of The Dispense Valves. Remove The Valves And Clean. You Can Take These Valves Apart By Hand As Shown. Replace The Assembly As Needed.
19 #1 100W CE CI LWARE CORPORATI O N E L E CT RI C A L DI AG RA M C - 20 03 G- I T 1 2 0 V ( 3 B UR NER S) L1 BE RG CONN ECT0RS TITL E : RE V BY DATE P2 L E D S P5 KEY S DE SCRIPTI ON KE YPAD S I NG LE NG 3 4A N 120V IN PU T C1 0.
Een belangrijk punt na aankoop van elk apparaat Cecilware C-2003G-IT (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Cecilware C-2003G-IT heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Cecilware C-2003G-IT vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Cecilware C-2003G-IT leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Cecilware C-2003G-IT krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Cecilware C-2003G-IT bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Cecilware C-2003G-IT kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Cecilware C-2003G-IT . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
