Gebruiksaanwijzing /service van het product 91995 van de fabrikant Chicago Electric
Ga naar pagina of 23
10” COMPOUND MITER SA W Model 91995 SET UP AND OPERA TING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally . Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight T ools ® .
Page 2 SKU 91995 For technical questions, please call 1-800-444-3353. SPECIFICA TIONS Electrical Requirements 120 V / 60 Hz / 1800 Input W atts. 15.0 AMPs Star t Up / 5300 RPM No Load. Three Prong, Grounded, P ower Cord Plug. P ower Switch T ype: Squeeze T ype.
Page 3 SKU 91995 For technical questions, please call 1-800-444-3353. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks.
Page 4 SKU 91995 For technical questions, please call 1-800-444-3353. A void accidental starting. Be sure the Power Switch is off before plugging in. Carrying power tools with your nger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents.
Page 5 SKU 91995 For technical questions, please call 1-800-444-3353. SER VICE T ool service must be performed only by qualied repair personnel. Service or maintenance performed by unqualied personnel could result in a risk of injury . When servicing a tool, use only identical replacement parts.
Page 6 SKU 91995 For technical questions, please call 1-800-444-3353. Before using the Miter Saw , make sure the Saw Blade is properly mounted on the Saw Spindle. Make sure the Saw Blade is balanced, and is not cracked or bent. The Saw Blade will become hot while cutting.
Page 7 SKU 91995 For technical questions, please call 1-800-444-3353. The Cross Pin (28) should always be in the “locked down” position when the Saw is not being used and when the Saw is being transported. The Cross Pin should be activated in the “locked up” position when changing Saw Blades.
Page 8 SKU 91995 For technical questions, please call 1-800-444-3353. Maintain this product with care. Keep the Miter Saw clean and dry for better and safer performance. For your safety , service and maintenance should be performed regularly by a qualied technician.
Page 9 SKU 91995 For technical questions, please call 1-800-444-3353. GROUNDING Improperly connecting the grounding wire can result in electric shock. Check with a qualied electrician if you are in doubt as to whether the outlet is properly grounded.
Page 10 SKU 91995 For technical questions, please call 1-800-444-3353. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
Page 1 1 SKU 91995 For technical questions, please call 1-800-444-3353. ASSEMBL Y AND OPERA TING INSTRUCTIONS Note: For additional references to the parts listed in the following pages, refer to the Assembly Diagram on page 24.
Page 12 SKU 91995 For technical questions, please call 1-800-444-3353. CAUTION! The Cross Pin (28) should always be activated in the “locked down” position when the Saw is not being used and when the Saw is being transported. The Cross Pin should be activated in the “locked up” position only when changing Saw Blades.
Page 13 SKU 91995 For technical questions, please call 1-800-444-3353. 8. Depress the Spindle Lock (84) to keep the Saw Blade (56) from turning. (See Figure H.) 6. Loosen the Screw (48) that holds the Large Cover (47) in place. Then, use the Wrench (1 10) to remove the Bolt (50).
Page 14 SKU 91995 For technical questions, please call 1-800-444-3353. 9. Use the Wrench (109) to unscrew and remove the Spindle Bolt (58). NOTE: The Spindle Bolt unscrews in a clockwise direction. Then, remove the Outer Flange (57). (See Figure I.) 1 1.
Page 15 SKU 91995 For technical questions, please call 1-800-444-3353. 1. A workpiece Clamp Assembly (36) can be installed by inserting the Assembly into the hole located in the Guide Fence (37). Once inserted, lock the Assembly in place with the Thumb Screw (35).
Page 16 SKU 91995 For technical questions, please call 1-800-444-3353. cannot be seen clearly , disconnect the electrical Power Cord from its electrical outlet and clean the Safety Cover with a soft, damp, cloth. A mild detergent may be used, but do not use solvents which may damage the Safety Cover .
Page 17 SKU 91995 For technical questions, please call 1-800-444-3353. T o Adjust The Cutting Depth: 1. W ARNING! Prior to performing this procedure, make sure the Power Cord (102) of the Miter Saw is unplugged from its electrical outlet. The Dust Bag: 1.
Page 18 SKU 91995 For technical questions, please call 1-800-444-3353. HANDLE (1) 6. If the Saw Blade (56) touches the T able (18) or any other part of the Saw Base (8), tighten the Screw (92) to raise the Saw Blade slightly until it clears. (See Figure O.
Page 19 SKU 91995 For technical questions, please call 1-800-444-3353. o 2. The bevel angle (or Saw Blade tilt capacity) may be adjusted from 0 - 45 to the left. T o do so, loosen the Handle (30) located at the rear of the Miter Saw . (See Figure P .) 3.
Page 20 SKU 91995 For technical questions, please call 1-800-444-3353. 6. Plug the Power Cord (102) into the nearest 120 volt, grounded, electrical outlet. 7. Squeeze the Power Switch (98) to turn on the Miter Saw . 8. When the Saw Blade (56) is turning at full speed, slowly bring down the Motor Housing (75) to complete the cut.
Page 21 SKU 91995 For technical questions, please call 1-800-444-3353. 3. Daily: With a soft brush, cloth, or vacuum, remove all dust and debris from the Miter Saw . Then, use a premium quality , lightweight machine oil to lubricate all moving parts except the Saw Blade (56).
Page 22 SKU 91995 For technical questions, please call 1-800-444-3353. P ARTS LIST NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts.
Page 23 SKU 91995 For technical questions, please call 1-800-444-3353. ASSEMBL Y DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts.
Een belangrijk punt na aankoop van elk apparaat Chicago Electric 91995 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Chicago Electric 91995 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Chicago Electric 91995 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Chicago Electric 91995 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Chicago Electric 91995 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Chicago Electric 91995 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Chicago Electric 91995 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Chicago Electric 91995 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
