Gebruiksaanwijzing /service van het product 12410 van de fabrikant Cisco Systems
Ga naar pagina of 64
CH A P T E R 4-1 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 4 System Startup and Basic System Configuration The system startup pro cess and a pr.
Chapter 4 System Startup and Basic System Configuration Sources of Cisco IOS Softwar e 4-2 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 This chapt.
4-3 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Boot Process Overview • A terminal de vice is connected to the console port on the RP , po wered on, and config ured for 9600 bps, 8 data bits, no pari ty , and 2 stop bits (9600, 8N2).
Chapter 4 System Startup and Basic System Configuration Powering On the Router and Obser ving the Boot Process 4-4 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 7.
4-5 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Powering On the Router and Observing the Boot Proc ess Step 4 Observe the RP alp hanumeric LED displays during t he RP boot process ( Figure 4-1 ).
Chapter 4 System Startup and Basic System Configuration Powering On the Router and Obser ving the Boot Process 4-6 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 Step 5 Observe the status of the RP interfaces (see Figure 4-2 for the GRP and Figure 4-3 for the PRP).
4-7 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Powering On the Router and Observing the .
Chapter 4 System Startup and Basic System Configuration Powering On the Router and Obser ving the Boot Process 4-8 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 Step 6 During the line card boot pr ocess, observe t he alphanumeric LED displays on each line card ( Figu re 4-4 ).
4-9 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Powering On the Router and Observing the Boot Proc ess RO M I GET The R OM image is being loaded into line card memory .
Chapter 4 System Startup and Basic System Configuration Powering On the Router and Obser ving the Boot Process 4-10 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Gui.
4-11 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Manually Booting the System Y ou do not .
Chapter 4 System Startup and Basic System Configuration Manually Booting the System 4-12 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 Locating a V.
4-13 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Manually Booting the System Caution Use the boot flash command with care.
Chapter 4 System Startup and Basic System Configuration Configuring the Router 4-14 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 Note If you did not chan ge the conf iguration register settin g, the nex t reload will re vert to the defa ult conf iguration re gister setting (0x0102).
4-15 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface Y ou can use the method that suits your operating style an d your kno wledge of network co nf iguration requirements.
Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface 4-16 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 The confi guration modes al low you to make changes to the running conf iguration file.
4-17 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface The follo wing example sho ws the change from user EXEC mode to pri vile ged EXEC mode.
Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface 4-18 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 Subinterface Co.
4-19 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface T o use the setup command to change a configuration: 1.
Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface 4-20 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 to configure each interface of the system.
4-21 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface line vty 0 4 password bambam no snmp server ! no ip routing ! interface Ethernet0 no shutdown ip address 172.
Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface 4-22 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 For e xample, d.
4-23 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface Configuring Host Name The host name you conf igure your router with must: • Follo w the rules for ARP ANET host names.
Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface 4-24 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 In either case, you cannot use a number as the f irst character . Spaces, howev er, are v alid password characters.
4-25 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface The follo wing configu ration dialog example sh ow s ho w to configure the syst em for an Ethernet interf ace that uses the IP netw ork layer protocol.
Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface 4-26 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 The follo wing example sho ws how to conf igure an A TM line card to use IP .
4-27 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface System image file is "tftp://xxx.xxx.xxx.xxx/directory/ghall/gsr-p-mz" cisco 12410/GRP (R5000) processor (revision 0x05) with 262144K bytes of memory.
Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface 4-28 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 Step 3 Enter the conf igure terminal command to enter global conf iguration mode.
4-29 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface clock source in.
Chapter 4 System Startup and Basic System Configuration Cisco IOS User Interface 4-30 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 Viewing the Running Configuration Settings Y ou can use the sh ow startup-conf ig command to vie w the current co nf iguration settings stored in NVRAM.
4-31 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Configuring the Software Configuration Registe r ! map-list atm1 ip 10.1.1.1 atm-vc 1 ip 10.
Chapter 4 System Startup and Basic System Configuration Configuring the Software Configuration Reg ister 4-32 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 • Read boot system commands from the configurati on fi le stored in NVRAM.
4-33 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Configuring the Software Configuration Registe r The boot f ield ( Ta b l e 4 - 5 ) defines a source for booting a def ault Cisco IOS software imag e required to run the router .
Chapter 4 System Startup and Basic System Configuration Configuring the Software Configuration Reg ister 4-34 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-.
4-35 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Configuring the Software Configuration Registe r For e xample, the filename formation process may yield a range of typical filenames li ke the follo wing: cisco2-grp .
Chapter 4 System Startup and Basic System Configuration Configuring the Software Configuration Reg ister 4-36 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-.
4-37 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Configuring the Software Configuration R.
Chapter 4 System Startup and Basic System Configuration Configuring the Software Configuration Reg ister 4-38 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-.
4-39 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Configuring the Software Configuration R.
Chapter 4 System Startup and Basic System Configuration Configuring the Software Configuration Reg ister 4-40 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 • Bits 11 and 12 of the softw are config uration re gister determine the data transmission rate of the console terminal.
4-41 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Recovering a Lost Password Recovering a Lost Password Use the follo wing procedure to recov er a lost password.
Chapter 4 System Startup and Basic System Configuration Recovering a Lost Password 4-42 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 enable “use.
4-43 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Recovering a Lost Password Step 7 Enter the enable command an d password (if prompted).
Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards 4-44 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 Using RP Fla.
4-45 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards Step 3 Insert the card into th e appropriate slot until th e card completely seats in the connector and the ejector button pops out (see Figure 4-5 b).
Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards 4-46 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 Figur e 4-5 .
4-47 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards Formatting a.
Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards 4-48 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 Specifying a Cisco IOS Software Image to Boot the System Use the procedure in this section to identify a specif ic Cisco IOS software image ( new .
4-49 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards Flash Memory Commands This section describes console commands th at you can use to access the different types of flash memories.
Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards 4-50 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 dir Command T o list the directory contents of the fl ash memory in use, enter the dir [ device-name ] command.
4-51 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards squeeze Comm.
Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards 4-52 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 Booting from.
4-53 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards Use the follo wing command to cop y a file to f l ash memory .
Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards 4-54 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 CCCCCCCCCCCC.
4-55 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards Use the following procedure to copy a boot able image into the flash memory card: Step 1 Boot the rout er .
Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards 4-56 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 Copying Cisc.
4-57 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards Step 3 Enter the follo wing commands to designate the f ile named im age.
Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards 4-58 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 Copying the .
4-59 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards Milo# copy startup-config slot0:myfile2 20575008 bytes available on device slot0, proceed? [confirm] Address or name of remote host [1.
Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards 4-60 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 Copying the .
4-61 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards Step 2 Enter.
Chapter 4 System Startup and Basic System Configuration Using RP Flash Memory Cards 4-62 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01 Booting a Ne.
4-63 Cisco 12010, Cisco 12410, and Cisco 12810 R outer Installation and Configuration Guide OL-11496-01 Chapter 4 System Startup and Basic System Configuration Post-Installation Procedures Post-Instal.
Chapter 4 System Startup and Basic System Configuration Post-Installation Procedures 4-64 Cisco 12010, Cisco 12410, and Cisco 1281 0 Router Installation and Configuration Guide OL-11496-01.
Een belangrijk punt na aankoop van elk apparaat Cisco Systems 12410 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Cisco Systems 12410 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Cisco Systems 12410 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Cisco Systems 12410 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Cisco Systems 12410 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Cisco Systems 12410 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Cisco Systems 12410 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Cisco Systems 12410 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.