Gebruiksaanwijzing /service van het product 1520 van de fabrikant Cisco Systems
Ga naar pagina of 36
G ETTING S TARTED G UIDE Cisco Aironet 1520 Series Outdoor Mesh Access Points INCLUDING LICENSE AND W ARRANTY 1 About this Guide 2 Introduction to the Access P oint 3 Unpac k ing the Access P oint 4 B.
2 1 About this Guide This guide is designed to familiarize y ourself with your Cisco Aironet 1520 Series Outd oor Mesh Access Point and prepare it for use in your wireles s network. Due to the complexity and number of product options available, this guide does not provide detailed mounting and configuration instructions.
3 Declaration of Conformity with Re gard to the EU Di rective 1999/5/EC (R&TTE Directive) This declaration is only valid for configurations (combinations of software, firmware and hardware) provided and/or supported by Cisco Systems.
4 War n in g This equipment must b e externally grounded using a c ustomer -supplied ground wire before power is applied . Contact the appropriate electrical inspection autho rity or an electrician if you are uncertain that suitable ground ing is available.
5 The access point is a standalone unit that can be cable strand or tower mounted. The access point ca n also operate as a relay node for other access po ints not directly connected to a wired network. Intelligent wireless rou ting is prov ided by the pa tent-pending Adaptive Wireless Path Protocol (A WPP).
6 • Cisco Aironet 1520 Series Outdoor Mesh Access Point Mounting Instructions • T ranslated Safety W arnings for Cisco Airo net 1520 Series Outdoor Mesh Acce ss Points • This guide Optional Equi.
7 Figure 1 shows the access point bottom co nnectors. Figur e 1 Access P oint Bott om Connectors Note Antenna port 5 is not shown in this illustration.
8 Figure 2 shows the access point left side and top connectors. Figur e 2 Access P oint Left Side and T op Connectors 1 Fiber connector 4 Antenna port 2 2 Cable Power over Cable (PoC ) connector 5 Ant.
9 Figure 3 shows the access point right side conn ections. Figure 3 A ccess Point Right Side Co nnections Radio Operation The 2.4-GHz radio supports three antennas fo r mu lti-input, single output (MISO) operation. The radio uses three receivers to support maximu m ratio combining (MRC) to enhance receiver performance.
10 External Antennas War n in g In order to comply wi th radio frequency (RF) exposure limits, the antennas for this product should be po sitioned no less than 6.
11 Note T o reduce potential radi o interference to other us ers, the antenna type and its gain should b e chosen so that the equivalent subtropical radia t ed power (EIRP) is not more than required for successful communicati on. T able 1 lists the supported external 2.
12 Power War n in g Installation of the equipme nt must comply with local and national electrical codes. Statement 1074 War n in g This equipment must b e externally grounded using a c ustomer -supplied ground wire before power is applied .
13 War n in g Connect the unit only to DC power source that complies with the Safety Extra-Low V oltage (SEL V) requirements in IEC 60950 based safety standards Statement 1033 • Internal 6 ampere-hour battery The access point can be connected to more than one power source.
14 Caution When the a ccess point is installed outdoors or in a wet or damp location, the AC branch circuit that is powering the access point sh ould be provided with ground fault protection (GFCI), as required by Article 210 of the National Electrical Code (NEC).
15 Cable Option The factory-orderable cable option provides a cabl e modem a nd Power -over -Cable capabilities for th e access point for high-speed data tr ansfer and Internet access. When the cable option is insta lled, the access point uses its F-type cable connection to re cei ve both data and power .
16 RAPs, each one parenting the same or different wir el ess networks. There can be more than one RAP for the same mesh network for redundancy . RAPs and MAPs can support wireless clients on the 2.4-GHz band. When the access point does not ha ve a wired Ethernet connection to the controller (through a swi tch), the radio role is called a MAP .
17 Figure 5 P o int-to-P oint Bridging Example Point-to-Multipoint Bridging The access points can be used as a RAP to connect multiple remote MAPs with their a ssociated wired networks. By default this capability is turned-off fo r all access points. T o s upport Ethernet bri dging, you must enable bridging on the controller for each access point.
18 Mesh Network The access point is typically deployed in a mesh ne twork configuration. In a typical mesh deployment, one or more RAPs have a wired network connection through a switch to a controller . Othe r remote MAPs without wired network connections use the backhaul feature to optimally link to a RAP that is connected to the wired network.
19 Layer 3 Network Operation The access points support Layer 3 network operat ion. Access points and controllers in Layer 3 configurations use IP addresses and UDP packets, which can be routed through large networks. Layer 3 operation is scalable and recommended by Ci sco.
20 Site Surveys Cisco recommends that you perform a si te survey before installing the equipment. A site survey reveals problems that can be resolved befo re the network is operational. Beca use 802.11a is unlicensed, there may be sources of interf erence from other 802.
21 T o av oid receiver damage and PER deg radation, you can use one of the following techniques: • Separate the omnidirectional antennas by at least 2 ft (0.6 m) to avoid receiver damage or by at least 25 ft (7.6 m) to avoid PER degradation. Note These distances assume free space path loss and are conservativ e estimates.
22 Before You Begin War n in g Read the installation instru ctions before connecting the sy stem to the power source. Statement 1004 Before you begin the installation p rocess: • Become familiar with the procedur es for mounting the access point.
23 Verifying the Wireless LAN Controller Mode Follow these steps to verify tha t the wirel ess LA N controller mode is set to Layer 3: Step 1 Open your web-browser and enter the IP address of your wireless LAN controller . Be sure to precede the IP address with https://.
24 Step 3 Under AAA in the left frame, click MAC Filtering . The Security MAC Filtering page appears. Step 4 Click New . The MAC Filters New page appe ars. Step 5 Enter the MAC address of the acce ss point in the MAC Address field. Y ou can also use the config macfilter add comma nd to add a MAC filter entry to the controller .
25 Deployment Notes Using a DHCP Server in a Layer 3 Mesh Network T o use a DHCP server in a Layer 3 me sh networ k, make sure the wireless LA N controller is in Layer 3 mode. Y ou must also configure DHCP option 43 on the DHC P server . After the controller is restarted, the access poi nt receives IP addresse s from the DHCP server .
26 T able 3 Lightweight Access P oint V C I Str ings The format of the TL V block for 1100, 1130, 1200, 12 40, 1250, 1300, and 1520 series access p oints is listed below: • T ype: 0xf1 (decimal 241).
27 T o co nfigure DHCP Option 43 for Cisco 1000 and 1500 (1505 and 1510) series lightweight access points in the embedded Cisco IOS DHCP server , follow these steps: Step 1 Enter configuration mode at the Cisco IOS command line interface.
28 T o configure DHCP Option 43 for Cisco Aironet 11 00, 1130, 1200, 1240, 1250, 1300, and 1520 series lightweight access points in the embedded Ci sco IOS DHCP server , follow these steps: Step 1 Enter configuration mode at the Cisco IOS CLI. Step 2 Create the DHCP pool, incl uding the necessary parameters such as default router and name serv er .
29 8 In Case of Difficulty Help is available from Cisco sho uld you experience di fficulties; however , before contacting Cisco, look for a solution to your problem in the following places: • The T .
30 Guidelines for Using the Access Point Y ou should keep these gu idelines in mind when you use the access point: • The access points can only communicate with controllers and cannot operate independently . • The access point communicates only with controlle rs and does not support W ireless Domain Services (WDS).
31 Figur e 9 LEDs 1 Status LED— Displays the current status of the access point and power . 3 Radio 1 Status LED—Displays the status of the 802.11b/g radio. 2 Uplink Status LED—Displays the status of all uplink connections (Ethernet, fiber , and cable).
32 See the Cisco Aironet 1520 Series Outdo or Mesh Ac cess Point Hardware Installation Guide for a detailed description of the LEDs and additional troub leshooting tips.
33 Controller CLI Use the show macfilter summary controller CLI command to view the MAC addresses added to the controller filter list. Controller GUI Log into your controller web interface (HTTPS) using a web browser and click SECURITY > AAA > MAC Filtering to view the MAC addresses added to the controller filter list.
34 c. Click Go . The Cisco warranty page appears. d. Read the document online, or click the PDF i con to download and print the document in Adobe Portable Document Format (PDF). Y ou can also contact the Cisc o service and support website for assistance : http://www.
35.
Americas Headquarters Cisco Systems, I nc. 170 W est T asman Drive San Jose, CA 95134- 1706 USA www .cisco. com T el: 408 5 26-4000 800 553-NETS (6387) Fax: 408 527-0883 Asia Pacific Headquarters Cisco Systems, In c. 168 Robinson Road #28-01 Capital T ower Singapore 068912 www .
Een belangrijk punt na aankoop van elk apparaat Cisco Systems 1520 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Cisco Systems 1520 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Cisco Systems 1520 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Cisco Systems 1520 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Cisco Systems 1520 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Cisco Systems 1520 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Cisco Systems 1520 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Cisco Systems 1520 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
