Gebruiksaanwijzing /service van het product AIRAP1041NAK9 van de fabrikant Cisco Systems
Ga naar pagina of 34
G ETTING S TARTED G UIDE Cisco Aironet 1040 Series Access Points 1 About this Guide 2 Safety In structions 3 Unpac k ing 4 Overview 5 Configuring the Access P oint 6 Additional Configuration for the A.
2 1 About this Guide This Guide provides in structions on how to inst all and configure your Cisco Aironet 1040 Series Access Point. This guide also provides mounting in structions and limited troubleshooting procedures.
3 War n in g Do not operate your wirel ess network device near u nshielded blasting caps or in an explosive environment unless the device has been mod ified to be especially qualified for such use. Statement 245B War n in g In order to comply wi th FCC radio frequency (RF) exposure limits, antenna s should be located at a minimum of 7.
4 3 Unpacking Follow these steps: Step 1 Unpack and remove the acce ss point and the accessory kit from the shipping box. Step 2 Return any pa cking material to the shippi n g container and save it for future use. Step 3 V erify that you hav e received the items listed below .
5 4 Overview The following illustrations show the ac cess point connections and features. Figur e 1 Access P oint P ort s and Connections 1 Kensington lock slot 4 Console port 2 Power connection 5 Sec.
6 5 Configuring the Access Point This section describes how to connect the access point to a wireless LAN controller . Because the configuration process takes plac e on the controller , see the Cisco Wireless LAN Controller Configuration Guide for additional information.
7 Access points must be discovered by a controller before they can become a n active part of the network. The 1040 series access point supports these controller discovery processes: • Layer 3 CAPW A.
8 Note Access points mounted in a building’ s environm ental airspace must be powered using PoE to comply with safety regulations. Cisco recommends that you make a site map showing access point loca.
9 Pre-Installation Configuration Setup Figure 2 shows the pre-installation configuration setup. Figure 2 Pr e-I nstallation Confi guration Setup Follow these steps to perform the pre-installa tion configuration. Step 1 Make sure that the Cisco wireless LAN controller DS port is connected to the network.
10 e. CAPW AP UDP ports (UDP 5246/5247) must not be blocked in the network. f. The access point must be able to find the IP address of the controller . This can be accomplished using DHCP , DNS, or IP subnet broadcast. This guide describes the DHCP method to convey the controller IP addres s.
11 Note If the access point remains in this mode for more than five minutes, the access point is unable to find the Master Cisc o wireless LAN contro ller. Check the connection between the access point and the Cisco wirele ss LAN controller and be sure that they are on the same subnet.
12 6 Additional Configuration for the Access Point in Autonomous Mode How you configure your access point depends on how you intend to use it in your wireless network.
13 Note The 802.11n radio only supports no encryption, WP A 2 Enterprise, and WP A-2 Personal. WP A-2 Enterprise and WP A-2 Personal requires AES encryption.
14 7 Mounting the Access Point Cisco Aironet 3500, 1260, 1140, 1130, a nd 1040 series access points can be mounted in several configurations, includin g on a suspended ceiling , on a hard ceiling or wall, on an elecrtical or netw ork box, and above a su spended ceiling.
15 Note A Master Cisco wireless LAN controller shoul d be used only for configuring access points and not in a working network. 9 Troubleshooting If you experience difficulty getti ng your access point installed and running, lo ok for a solution to your problem in this guide or in additional access po int documentation.
16 Figur e 3 Access P oint LED Location 1 Status LED 272378 1.
17 T able 1 shows the access point Status LED indications for various conditio ns. T able 1 LED Status Indicati ons Message Ty p e Status LED Message Meaning Boot loader status sequence Blinking green.
18 Troubleshooting the Ac cess Point Join Process Access points can fail to join a controller for many reasons: a R ADIUS auth orization is pending; self-signed certificat es are not enabled on the cont roller; the access point’ s and controller’ s regulatory domains don’ t match, and so on.
19 Y ou can view join-rel ated information for the following numbers of access points: • Up to 300 access points for 4400 series contro llers, the Ci sco WiSM, and the Catalyst 3750G Integrated Wire.
20 10 Declarations of Conformity and Regulatory Information This section provides declarations of conformity and regulatory information for the Cisco Aironet 1040 Series Access Point. Manufacturers Federal Communicati on Commission Declaration of Conformity Statement Manufacturer: Cisco Systems, Inc.
21 interference will not occur . If this equipment does ca use interference to radio or television reception, which can be determined by turning th e equipment o ff and on, the user is encouraged to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna.
22 Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interf erence when operating Cisc o Aironet access points in Japan.
23 Statement 371—Power Cable and AC Adapter English Translation When installing th e product, please use the provided or d esignated connection cable s/power cables/AC adaptors.
24 Cisco Aironet Access Points are cert ified to the requiremen ts of RSS-210. The use of this device in a system operating either parti ally or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations.
25 Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC.
26 The following standards were applied: • Radio—EN 300.328-1, EN 300.328-2, EN 301.893 • EMC—EN 301.489-1, EN 301.489-17 • Safety—EN 60950-1.
27 Note This equipment is intended to be used in a ll EU and EF T A countries. Outdoor use may be restricted to certain frequencie s and/or may require a license fo r operation. For more details, contact Cisco Corporate Compliance. The following CE mark is affixed to the access point w ith a 2.
28 Australia This system has been evaluated fo r RF exposure for Humans as refe renced in the Australian Radiation Protection standard and has been evaluated to the ICNIRP (International Commission on Non-Ionizing Radiation Protection) limits. The mi nimum separation distance from the antenna to general bystander is 20cm (7.
29 English Translation Administrative Rules for Low- power Radio-Frequency Devices Article 12 For those low-power radio-frequenc y devices that have alrea dy receiv ed a type-ap proval, comp anies, business units or users should not change its freque ncies, increase its power or change its original features and functions.
30 English Translation Low-power Radio-frequency Devices T e chnical Specifications Operation of Cisco Aironet Access Points in Brazil This section contains special information for oper ation of Cisco Aironet access points in Brazil. Access Point Models AIR-AP1042N-T -K9 AIR-LAP1042N-T -K9 AIR-AP1041N-A-K9 AIR-LAP1041N-A-K9 4.
31 Regulatory Information Figure 4 contains Brazil regulatory information for th e access po int models identified in th e previous section. Figur e 4 Br azil Regulato ry Inf or mation Portuguese Tran.
32 11 Configuring DHCP Option 43 and DHCP Option 60 This section contains a DHCP Option 43 configu ration example on a Windows 2003 Enterprise DHCP server for use with Cisco Aironet lightweig ht acce ss points. For other DHCP server implementations, consult product documentation for configuring DHCP Option 43.
Americas Headquarters Cisco Systems, I nc. 170 W est T asman Drive San Jose, CA 95134- 1706 USA www .cisc o.com T el: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Asia Pacific Headquarters Cisco Systems (USA) Pte. Ltd. 168 Robinson Road #28-01 Capital T ower Singapore 068912 www .
34 Safety UL 60950-1 CAN/CSA C22.2 No. 60950-1 IEC 60950-1 with all national deviations EN 60950-1 UL 2043 EMI and Susceptibility FCC Part 15.107 and 15.109 Cla ss B ICES-003 Class B (Canada) EN 301.489 EN 55022 Class B, 2000 version EN 55024 AS/NZS 3548 Class B VCCI Class B Radio FCC Part 15.
Een belangrijk punt na aankoop van elk apparaat Cisco Systems AIRAP1041NAK9 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Cisco Systems AIRAP1041NAK9 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Cisco Systems AIRAP1041NAK9 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Cisco Systems AIRAP1041NAK9 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Cisco Systems AIRAP1041NAK9 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Cisco Systems AIRAP1041NAK9 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Cisco Systems AIRAP1041NAK9 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Cisco Systems AIRAP1041NAK9 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
