Gebruiksaanwijzing /service van het product ASR 1004 van de fabrikant Cisco Systems
Ga naar pagina of 38
Q UICK S TART G UIDE Cisco ASR 1004 Router 1 Documentation and R esources 2 Prepare for Installation 3 Rac k-Mount the Router 4 Connect the Router to the Network 5 Start the S ystem 6 Configure the R .
2 1 Documentation and Resources Documentation for the Cisco 1000 Series Ag gregation Services Routers documen tation is online with the exception of the regulatory compliance a nd sa fety documentation and the Cisco 1000 Se ries Aggregation Servic es Routers documentation flyer .
3 2 Prepare for Installation This section contains information about tools and parts, wa rnings, site preparation information, and information for rack-mount and equipment shelf or tabletop in stallation. War n in g Only trained and qualified p ersonnel should instal l, replace, or service this equipment.
4 Prepare for Rack-Mount Installation Before you begin the rack-mounting tasks: • Decide whether or not you want to fr ont- mount or rear -mount the chassis • Decide whether or not you want to attach ca ble-management brackets to your chassis.
5 Step 6 T o install the Cisco ASR 1004 Router in an equipment rack, see “Four-Post Rack Installation” section on page 6 or “Two-Post Rack Installation” section on page 8 . Note If you install cable management b rackets, make certain th at the chassis is mounted in the equipment rack first.
6 Four-Post Rack Installation This section describes the types of racks used for rack-mounting the chassis. Figure 3 Installing the Cisco ASR 1 0 04 Router in a F our -P ost Rack Note Because the rack.
7 Step 5 Lift the chassis in to position between the rack posts (requires two people). Step 6 Align the mounting bracket holes wi th the rack post holes and attach the chassis to the rack.
8 Two-Post Rack Installation The Cisco ASR 1004 Router can be installed in a two- post rack, either 19 inch or 23 inch. Note Inner clearance (the width between the inner sides of the two po sts or rails) must be at leas t 19 inches (48.26 cm). The height of the chassis is 1.
9 Step 4 Hold the chassis in position against th e mounting rails and follow these steps: a. Insert the bottom screw into the third hole up from the botto m of the rack mount ear and use a hand-held screwdriver to tighten the screw to the rack rail (see Figure 4 ).
10 Figure 5 Attac hing the Cabl e-Management Brack et to the Cisco ASR 1 0 04 Router Step 3 Using the bottom rack-mount ear hole, insert the screw th rough cable-management bracket and into the chassis rack-mount (see Figure 5 ). Figure 4 shows the cable-management brackets attached to the chassis in a rack.
11 Figure 6 Chassis Ground Lug Locat ion on the Ci sco ASR 1 004 Router Use the following procedure to attach the grounding lug to the chassis g round connector on your ch assis: Step 1 Use the wire stripper to strip one end of the A W G #6 wire approximately 0.
12 Step 5 Locate the chassis gro und connector on the side of your c hassis. Step 6 Insert the two screws through the holes in the groundi ng lug. Step 7 Use the Number 2 Phillips screwdriver to carefully ti ghten th e screws until the grounding lug is held firmly to the chassis.
13 Step 2 After you establish normal router operat ion, you can disconnect th e terminal. Note For console and auxiliary port pino uts, see Appendix A in the Cisco ASR 1000 Series Aggr egation Services Routers Hardware Installation and Initial C onfiguration Guide.
14 Step 3 Insert an E thernet RJ-45 cable into the MG MT ETHERNET por t. Step 4 Insert the other end of the RJ-45 cable to your management device or netw ork.
15 Step 3 Insert the AC power cable into the power supply inlet. Step 4 Plug the power supply cable into the power source. Step 5 The power supply LEDs light when power is supplied to the router . Figur e 1 0 Cisco A SR 1 0 04 Router A C P ower Supply Step 6 T urn the power supply Standby switch to On (|) position.
16 War n in g This equipment must be grounded. Neve r defeat the ground conductor or operate the equipm ent in the absence of a suitably installed ground conductor . Contact the appropriate electrical inspection authority or an elec trician if you are uncertain that suitable grounding is available.
17 Figure 10 shows the DC power supply for the Cisco ASR 1004 Router . DC Power Supply for the Cisco ASR 1004 Router The Cisco ASR1004 has two of the same type power suppli e s in power supply Slot 0 and power sup ply Slot 1. Caution Before you connect DC-input power , you must install the DC power ground leads to the DC power su pply .
18 Figur e 1 1 DC Po wer Supply Gr ounding S tud Location and Connection on the Cisco A SR 1 004 Router Step 1 Make certain that the chassis ground is connected before you begin installing the DC po wer supply .
19 Figur e 12 Cisco A SR 1 0 04 Router DC P ower Supply T erminal Block Caution Before you continue to install the terminal block wires, stop and perform Step 3 to prevent any contact with metal lead on the ground wire. Step 3 Y ou must wrap the positiv e and negative cables with sleevi ng.
20 Step 8 Connect the other ends of the terminal block cables to the site gro und connectio n. Move the circuit-br eaker swit ch to the On position (|). This completes the procedure for conn ecting DC-input power . Y o ur installation is co mplete. Proceed to the “Start the System” section on page 14 to start the rout er .
21 – Make certain that each shared port adapter is firmly seated in its subslot and its captive screws are securely tightened. – The Cisco ASR1000-ESP10 forwarding proces sor in the Cisco AS R 1004 router is in serted in sl ot F0, is firmly seated in its slot, and its captive screws are secu rely tightened.
22 Located rp_super.ppc.nader.5g.evfc.bin Image size 211681484 inode num 12, bks cnt 51681 blk size 8*512 ##############################################################################################.
23 32768K bytes of non-volatile configuration memory. 1869396K bytes of physical memory. 7798783K bytes of eUSB flash at bootflash:. --- System Configuration Dialog --- Would you like to enter the initial configuration dialog? [yes/no]: no Press RETURN to get started! *Feb 19 17:34:27.
24 *Feb 19 17:35:22.221: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF Step 6 Router> 6 Configure the Router Use this section for information on configuring the Cisco A SR 1004 Router .
25 Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system. --- System Configuration Dialog --- Would you like to enter the initial configuration dialog? [yes/no]: y At any point you may enter a question mark '?' for help.
26 enable password tests line vty 0 4 password test no snmp-server ! ip routing no bridge 1 no clns routing ! interface GigabitEthernet0/0/0 shutdown no ip address ! interface GigabitEthernet0/0/1 shu.
27 shutdown no ip address dialer-list 1 protocol ip permit dialer-list 1 protocol ipx permit ! end [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit.
28 zimage at: 00807673 009B8E53 initrd at: 009B9000 01006E53 isord at: 01007000 0CD2A000 avail ram: 00400000 00800000 Kernel load: Uncompressing image.
29 Note Basic management setup configures en o ugh connectivity for managing the system; extended setup will ask you to configure each inte rface on the system. For detailed info rmation about setting glob al parameters, refer to the Cisco ASR 1000_Series Aggregation Services R outers Software Configura tion Guide.
30 7 After Installation Follow the instructions in this section to replace components after installation. The follo wing topics are covered in this sect ion: • Power Off the Cisco ASR 1004 Router, p.
31 Note T wo power supplies must be insta lled in the chassis at all time s to ensure sufficient cooling. The system fans are inside the power supply units and must spin for cooling. Because al l the system fans can be powered by one power supply , the second power supply unit does not ha ve to be powered on, but it must be insta lled.
32 b. Unscrew the positive cable Ke p nu t s c r ew , wa s he r , a n d g ro u n d l ug , and remove the stud and lea d wire. c. Unscrew the earth ground Kepnut screw , washer , a nd ground lug and remove the stud and lead ground wire. Step 6 Loosen the captive screws on the DC pow er supply .
33 Figur e 13 Cisco A SR 1 0 04 Router DC P o w er Supply Groun ding Wir e and Stud Step 5 Attach the other end of the ground cable to the site ground connection. Caution Before you continue to install the terminal block ground wires, stop and perform Step 6.
34 Step 8 T ighten the Kepnut screw (use the screwdriver to tighten the ground screw in the terminal block to a torqu e of 8 in-lbs / 4 per .) and repeat the same steps for the positive ground stud and wire. Note Secure the wires coming in from the terminal block so that they ca nnot be disturbed by casual contact.
35 Step 6 T o remove the SIP , first disconnect all ca bles from each SP A. Step 7 Loosen the locking thumbscrews on both sides of the SIP . Step 8 Slide the SIP out of the module slot. If you are removing a bl ank filler plate, pull the blank filler plate completely out of the module slot.
36 Caution The shared port adapter must slide into the slo t guides under the chassis lid. Do not allow the shared port adapter components to come in contact with the system boa rd or the shared port adapter could be damaged. Step 6 Carefully slide the shared port adapter into the shared port adapter slot and sea t it.
Americas Headquarters Cisco Systems, Inc. 170 W est T asman Drive San Jose, CA 95134-1706 USA www .cisco.com T el: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Asia Pacific Headquarters Cisco Systems, Inc. 168 Robinson Road #28-01 Capital T ower Singapore 068912 www .
38.
Een belangrijk punt na aankoop van elk apparaat Cisco Systems ASR 1004 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Cisco Systems ASR 1004 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Cisco Systems ASR 1004 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Cisco Systems ASR 1004 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Cisco Systems ASR 1004 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Cisco Systems ASR 1004 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Cisco Systems ASR 1004 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Cisco Systems ASR 1004 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
