Gebruiksaanwijzing /service van het product PMU2XXX van de fabrikant Citizen Systems
Ga naar pagina of 312
Command Reference MODEL : CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 PMU2XXX Revision 0.04 2007/8/29.
CITIZEN is a registered trade mark of CI TIZEN HOLDINGS CO., L TD., Japan. CITIZEN es una marca registrada de CITI ZEN HOL DINGS CO., L TD., Japón. REVISON Rev No. Date Comment 0.00 2006/9/26 Newly isuued 0.01 2006/11/22 Add progr am sample for F S p and FS q 0.
- 3 - TABLE OF CONTENTS TABLE OF CONTENTS ................................................................................... 3 1. OUTLINE ................................................................................................... 9 1.1 O PERATION M ODE .
- 4 - ESC t n ............................................................................................................................... ............ 51 ESC { n .....................................................................................
- 5 - 2.2.11 Cutter Commands ....................................................................................................... 100 ESC i ............................................................................................................
- 6 - 2.2.15 Black Mark Control Commands ................................................................................. 143 GS FF ......................................................................................................................
- 7 - fn=82 ： F u nc t i o n 8 2 Sending the size of 2-dimensional code data in 2-dimensio nal code data storage area ............................................................................................................................... ...
- 8 - 4. MEMORY SWITCH ................................................................................ 265 4.1 M EMORY S WITCHES .................................................................................................. 265 4.1.1 CT-S280 ....
- 9 - 1. OUTLINE 1.1 Operation Mode Our printer has ESC/POSTM as control command s. 1.2 Character Set All print data sent from th e host compute r to the printer are aut omatically converted to one-byte alp hanumeric or katakana character s (ANK) or two-byte Kanji corresponding to the char acters and symbol s.
- 10 - 2. CONTROL COMMANDS 2.1 ESC/POS Command List 2.1.1 CT-S280 Print Control Commands Commands Function MODE GS P Page LF Printing and paper f eed S ・ P 31 CR Back to printing S ・ P 32 FF Print.
- 11 - Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line f eed rate S ・ P 74 ESC 3 Setting line feed rate of mini mum pitch S ・ P ○ 75 Bit Image Commands Comm.
- 12 - Kanji Control Commands Command Function MODE GS P Page FS ! Collectively setting Kanji print mode S ・ P 132 FS & Setting Kanji mode S ・ P 133 FS - Setting/Canceling Kanji underl ine S .
- 13 - 2.1.2 CT-S300/CT-S310 Print Contorl Commands Command Function MODE GS P Page LF Printing and paper f eed S ・ P 31 CR Back to printing S ・ P 32 FF (1)Pri nting in PAGE MODE and re turning to.
- 14 - Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line f eed rate S ・ P 74 ESC 3 Setting line feed rate of mini mum pitch S ・ P ○ 75 Bit Image Commands Comm.
- 15 - Kanji Control Commands Command Function MODE GS P Page FS ! Collectively setting Kanji print mode S ・ P 132 FS & Setting Kanji mode S ・ P 133 FS - Setting/Canceling Kanji underl ine S .
- 16 - 2.1.3 CT-S2000 Print Contorl Commands Command Function MODE GS P Page LF Printing and paper f eed S ・ P 31 CR Back to printing S ・ P 32 FF (1)Pri nting in PAGE MODE and re turning to STANDA.
- 17 - Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line f eed rate S ・ P 74 ESC 3 Setting line feed rate of mini mum pitch S ・ P ○ 75 Bit Image Commands Comm.
- 18 - Commands for Non-volatile Memory Command Function MODE GS P Page G S ( C Editing user NV m emory S 112 G S ( L G S 8 L Specifying graphics data S 118 G S g 0 Initializing mainten ance counter S.
- 19 - Other Commands Command Function MODE GS P Page DLE ENQ Real-time r equest to print er S ・ P 219 DLE DC4 Outputting specified p ulse in real-time/Buff er clear S ・ P 220 / 221 ESC ＝ Data i.
- 20 - 2.1.4 CT-S4000 Print Contorl Commands Command Function MODE GS P Page LF Printing and paper f eed S ・ P 31 CR Back to printing S ・ P 32 FF (1)Pri nting in PAGE MODE and re turning to STANDA.
- 21 - Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line f eed rate S ・ P 74 ESC 3 Setting line feed rate of mini mum pitch S ・ P ○ 75 Bit Image Commands Comm.
- 22 - Commands for Non-volatile Memory Command Function MODE GS P Page G S ( C Editing user NV m emory S 112 G S ( L G S 8 L Specifying graphics data S 118 G S g 0 Initializing mainten ance counter S.
- 23 - Other Commands Command Function MODE GS P Page DLE ENQ Real-time r equest to print er S ・ P 219 DLE DC4 Outputting specified p ulse in real-time/Buff er clear S ・ P 220 / 221 ESC ＝ Data i.
- 24 - 2.1.5 BD2-2220 Print Contorl Commands Command Function MODE GS P Page LF Printing and paper f eed S ･ P 31 CR Back to printing S ･ P 32 FF Printing in P AGE MODE and returni ng to ST AN DAR.
- 25 - Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S ･ P 76 GS * Defining the downl oad bit image S ･ P 77 GS / Printing the downloaded bit i mage S ･ .
- 26 - Kanji Control Commands Command Function MODE GS P Page FS ! Collectively setting Kanji print mode S ･ P 132 FS & Setting Kanji mode S ･ P 133 FS - Setting/Canceling Kanji underl ine S .
- 27 - 2.1.6 PMU2XXX Print Contorl Commands Command Function MODE GS P Page LF Printing and paper f eed S ･ P 31 CR Back to printing S ･ P 32 FF (1)Pri nting in PAGE MODE and re turning to STANDAR.
- 28 - Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S ･ P 76 GS * Defining the downl oad bit image S ･ P 77 GS / Printing the downloaded bit i mage S ･ .
- 29 - Kanji Control Commands Command Function MODE GS P Page FS ! Collectively setting Kanji print mode S ･ P 132 FS & Setting Kanji mode S ･ P 133 FS - Setting/Canceling Kanji underl ine S .
- 30 - 2.2 Command Details 2.2.1 Description of Items XXXX support model [Function] The name of a comman d. [Code] The string of code s comprising the comm and is represented by < > H f or hexadecimal number s, < > B for binary numbers, and < > for decimal numbers, [ ] k de notes the number of repetiti on of “k” time s.
- 31 - 2.2.2 Print Control Commands LF CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Printing and paper feed [Code] < 0A > H [Outline] [The specification which i s common to the model] Prints data inside the print buffer and f eeds paper based on the line feed am ount having been set .
- 32 - CR CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Back to printing [Code] < 0D > H [Outline] [The specification which i s common to the model] (1) When me mory switch 1-5 is OFF: This comman d is ignored .
- 33 - FF （ At selection of PAGE MODE ） CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Printing in PAG E MODE and returning to STANDARD MODE (at the sel ection.
- 34 - ESC FF CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Printing data in PAGE MODE [Code] < 1B > H < 0C > H [Outline] [The specification which i s common to the model] Executes a batch printout of the data mappe d in the entire print area in PAGE MOD E.
- 35 - ESC J n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Printing and feeding paper in minimum pitch [Code] < 1B > H < 4A > H < n > [Range] .
- 36 - ESC d n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Printing and feeding the paper by “n” lines [Code] < 1B > H < 64 > H < n > [Range] 0 ≦ n ≦ 255 [Outline] [The specification which i s common to the model] Prints data in the print buffer and feeds paper by “ n” lines.
- 37 - 2.2.3 Print Character Commands CAN CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Canceling print data in PAG E MODE [Code] < 18 > H [Outline] [The specification which i s common to the model] Erases all data contained i n the currently effective prin t area in PAGE MODE.
- 38 - ESC SP n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting the right spacing of the ch aracter [Code] < 1B > H < 20 > H < n > [Range].
- 39 - ESC ! n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Collectively specifying the prin ting mode [Code] < 1B > H < 21 > H < n > [Range] 0 ≦ n ≦ 255 [Outline] [The specification which i s common to the model] Printing mode is assig ned.
- 40 - [Caution] • With doubl e height and double width b eing specified simultaneou sly, quadruple characters are created. • An underline is attached to the full character wi dth, whic h, however, is not attached to the part having been skipped by the horizontal tab (HT) .
- 41 - ESC % n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying/canceling download character set [Code] < 1B > H < 25 > H < n > [Range] 0 ≦ n ≦ 255 [Outline] [The specification which i s common to the model] Specifying/canceling download characters.
- 42 - ESC & s n m [ a [p] s x a ] m-n+1 CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Defining the do wnload characters [Code] < 1B > H < 26 > H .
- 43 - [Example] F o n t A 24dot 12dot p4 p5 p6 p36 p35 p34 MSB p3 p2 p1 LSB Create each data bi t by setting “1” for a printed dot and “0” for an unprinted dot.
- 44 - ESC - n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying /canceling underlin e [Code] < 1B > H < 2D > H < n > [Range] 0 ≦ n ≦ 2 、 48 ≦ n ≦ 50 [Outline] [The specification which i s common to the model] Specifying /canceling an underline.
- 45 - ESC ? n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Deleting downl oad charact ers [Code] < 1B > H < 3F > H < n > [Range] 32 ≦ n ≦ 126 [Outline] [The specification which i s common to the model] Deletes the d ownloaded char acters of spec ified code.
- 46 - ESC E n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying/canceling emph asis printing [Code] < 1B > H < 45 > H < n > [Range] 0 ≦ n ≦ 255 [Outline] [The specification which i s common to the model] Specifying/canceling the emp hasized character s.
- 47 - ESC G n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying/canceling double strike printing [Code] < 1B > H < 47 > H < n > [Range] 0 ≦ n ≦ 255 [Outline] [The specification which i s common to the model] Specifying /canceling th e double strike printing.
- 48 - ESC M n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Selection of ch aracter fonts [Code] < 1B > H < 4D > H < n > [Range] 0 ≦ n ≦ 2 、 48 ≦ n ≦ 50 [Outline] [The specification which i s common to the model] Selects char acter font s.
- 49 - ESC R n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Selecting the internation al character set [Code] < 1B > H < 52 > H < n > [Range] C.
- 50 - ESC V n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying/canceling 90°-rig ht-turned characters [Code] < 1B > H < 56 > H < n > [.
- 51 - ESC t n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Selectin g the charac ter code table [Code] < 1B > H < 74 > H < n > [Range] 0 ≦ n ≦ 9 、 16 ≦ n ≦ 19 、 n=26 、 40 、 255 [Outline] [The specification which i s common to the model] Selecting the char acter code table.
- 52 - ESC { n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying/canceling the inv erted charac ters [Code] < 1B > H < 7B > H < n > [Range] 0 ≦ n ≦ 255 [Outline] [The specification which i s common to the model] • “n” is valid only for the lowest bit (n0).
- 53 - ESC ~ J n （ V alid in CBM-270-Compatible Mode ） CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifies/cancels printing in red (black-based paper) [Code] < 1B > H < 7E > H < 4A > H < n > [Range] 0 ≦ n ≦ 255 [Outline] Specifies or cancel s printing in red .
- 54 - ESC ~ J n （ V alid in CBM1000-Compatible Mode ） CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifies/cancels printing in red (black-based paper) [Co.
- 55 - DC3 n （ V alid in CBM-270-Compatible Mode ） CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifies/cancels printing in red (black-based paper) [Code] < 13 > H < n > [Range] 0 ≦ n ≦ 255 [Outline] Specifies or cancel s printing in red .
- 56 - DC3 n （ V alid in CBM1000-Compatible Mode ） CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifies/cancels printing in red (black-based paper) [Code] < 13 > H < n > [Range] 0 ≦ n ≦ 255 [Outline] [The specification which i s common to the model] Specifies or cancel s printing in red .
- 57 - GS ! n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying the character si ze [Code] < 1D > H < 21 > H < n > [Range] 0 ≦ n ≦ 25.
- 58 - [Caution] [The specific ation which is common to the model ] • This co mmand is val id for all cha racters (alpha numeric, kana , and kanji) e xcept for HRI characters . • This command is ignored if either the vert ical magnification or horizontal magnif ication is out of the defined ran ge.
- 59 - GS B n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying/canceling the bl ack/white inverted printing [Code] < 1D > H < 42 > H < n &g.
- 60 - GS b n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying/canceling the smoothing [Code] < 1D > H < 62 > H < n > [Range] 0 ≦ n ≦ 255 [Outline] [The specification which i s common to the model] This comman d specifies or cancels t he smoothing .
- 61 - 2.2.4 Print Position Commands HT CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Horizontal tab [Code] < 09 > H [Outline] [The specification which i s common to the model] Shifts the printing position to th e ne xt horizontal tab po sition.
- 62 - ESC $ n1 n2 CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying the absolut e positions [Code] < 1B > H < 24 > H < n1 >< n2 > .
- 63 - ESC D [n]k NULL CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting horizontal tab position [Code] < 1B > H < 44 > H[ < n > ]k < 00 > H [Range] 1 ≦ n ≦ 255 0 ≦ k ≦ 32 [Outline] [The specification which i s common to the model] Specifying a horizon tal tab position.
- 64 - ESC T n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Selecting the char acter printing direc tion in PAGE MOD E [Code] < 1B > H < 54 > H < .
- 65 - ESC W xL xH yL yH dxL dxH dyL dyH CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Defining the print area in PAGE MODE [Code] < 1B > H < 57 > H &.
- 66 - [Default] xL=xH=yL=yH=0 dyL=126 、 dyH=6 dxL,dyH depends on p aper width. (Ref er to the belo w Table) paper width print wid th/(dot) dxL dxH support model 112mm 104mm/(832) 96 3 CT-S4000 112mm 90mm/(720) 208 2 CT-S4000 83mm 82.
- 67 - ESC ＼ nL nH CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying the relative position [Code] < 1B > H < 5C > H < nL >< nH > .
- 68 - ESC a n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Aligning the characters [Code] < 1B > H < 61 > H < n > [Range] 0 ≦ n ≦ 2 、 48.
- 69 - GS $ nL nH CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying the ab solute position of character verti cal direction in PAGE MODE [Code] < 1D >.
- 70 - GS L nL nH CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting the left margin [Code] < 1D > H < 4C > H < nL >< nH > [Range] 0 .
- 71 - GS W nL nH CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting the print area width [Code] < 1D > H < 57 > H < nL >< nH > [Range] 0 ≦ nL ≦ 255 0 ≦ nH ≦ 255 [Outline] [The specification which i s common to the model] Sets the print area width specified by nL and nH.
- 72 - (2) If a sufficient area c annot be provided as a r esult of step (1), the print area i s extended toward the left (so, th e left margin is decreased).
- 73 - GS ＼ nL nH CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying the relativ e vertical position of a charac ter in PAGE MOD E [Code] < 1D > H &.
- 74 - 2.2.5 Line Feed Span Commands ESC 2 CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying 1/6-inch lin e feed rate [Code] < 1B > H < 32 > H .
- 75 - ESC 3 n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting line feed rate of mini mum pitch [Code] < 1B > H < 33 > H < n > [Range] 0 .
- 76 - 2.2.6 Bit Image Commands ESC * m n1 n2 [d] k CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying the bit image mode [Code] < 1B > H < 2A >.
- 77 - GS * n1 n2 [d] n1xn2x8 CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Defining the downl oad bit image [Code] < 1D > H < 2A > H < n1 ><.
- 78 - GS / m CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Printing the do wnloaded bit im age [Code] < 1D > H < 2F > H < m > [Range] 0 ≦ m ≦ 3 、 48 ≦ m ≦ 51 [Caution] [The specific ation which is common to the model ] Prints downloaded bit image in a mod e specified by “m”.
- 79 - GS v 0 m xL xH yL yH d1 ... dk CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Printing of raster bit imag e [Code] < 1D > H < 76 > H < 30 >.
- 80 - [Example] When xL + xH x 256 = 64 ( xL+xH×256 )×8 dots = 512 dots ド ト ドト 2 3 1 62 64 63 7 6 5 4 3 2 1 0 yL+yH×256 dots 128 127 126 68 67 65 K- 1 K- 2 K MSB LSB.
- 81 - 2.2.7 Status Commands DLE EOT n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [See Also] [Caution] • Each statu s represents the current statu s.
CT-S280 (1) Printer status (When n = 1 is specified) (3) Status caused by an error (w hen n = 3 is specified) Bit Status Hex. Decimal Bit Status Hex. Decimal 0 Fixed 00 0 0 Fixed 00 0 1 Fixed 02 2 1 F.
CT-S300 / CT-S310 (1) Printer status (When n = 1 is specified) (3) Status caused by an error (w hen n = 3 is specified) Bit Status Hex. Decimal Bit Status Hex. Decimal 0 Fixed 00 0 0 Fixed 00 0 1 Fixed 02 2 1 Fixed 02 2 No B.M detection error occurred Status of pin 3 of drawer kick-out connector = L 00 0 00 0 2 (only when B.
CT-S2000 (1) Printer status (When n = 1 is specified) (3) Status caused by an error (w hen n = 3 is specified) Bit Status Hex. Decimal Bit Status Hex. Decimal 0 Fixed 00 0 0 Fixed 00 0 1 Fixed 02 2 1 Fixed 02 2 Status of pin 3 of drawer kick-out connector = L 00 0 No B.
CT-S4000 (1) Printer status (When n = 1 is specified) (3) Status caused by an error (w hen n = 3 is specified) Bit Status Hex. Decimal Bit Status Hex. Decimal 0 Fixed 00 0 0 Fixed 00 0 1 Fixed 02 2 1 Fixed 02 2 Status of pin 3 of drawer kick-out connector = L 00 0 No B.
BD2-2220 (1) Printer status (When n = 1 is specified) (3) Status caused by an error (w hen n = 3 is specified) Bit Status Hex. Decimal Bit Status Hex. Decimal 0 Fixed 00 0 0 Fixed 00 0 1 Fixed 02 2 1 .
Hex. Decimal - 87 - PMU2XXX (1) Printer status (When n = 1 is specified) Bit Status Hex. Decimal 0 Fixed 00 0 1 Fixed 02 2 2 Fixed 04 4 Online status 00 0 3 Offline status 08 8 4 Fixed 10 16 Not waiti.
- 88 - ESC u n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Sending the peripheral device status [Code] < 1B > H < 75 > H < n > [Outline] [The specification which i s common to the model] Send the current drawer kick connector pin# 3 status.
- 89 - ESC v CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Transmis sion of printer status [Code] < 1D > H < 76 > H [Outline] [The specification which i s common to the model] Transmits curr ent printer status .
- 90 - GS a n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Enabling/disab ling ASB (Automatic S tatus Back) [Code] < 1D > H < 61 > H < n > [Ran.
- 91 - (1) 1st b yte (Printer informa tion) Bit Status Hex. Decimal 0 Unused 00 0 1 Unused 00 0 Status of pin 3 of dr awer kick-out connector = “L” 00 0 2 Status of pin 3 of drawer ki ck-out conne.
- 92 - (4) 4t h byte (Pape r Sensor info rmation) In case of MSW3-7 ON Bit Status Hex. Decimal 0 Undefined － － 1 Undefined － － 2 Undefined － － 3 Undefined － － 4 Unused 00 0 5 Undefined － － 6 Undefined － － 7 Unused 00 0 In case of MSW3-7 OFF (CBM100 0 non-compatible mode ) Bit Status Hex.
- 93 - GS r n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Sending status [Code] < 1D > H < 72 > H < n > [Range] CT-S280 / BD2 -2220 / P MU2XXX.
- 94 - • Paper Sensor status (n = 1, 49) Bit Status Hex. Decimal Paper found b y Paper Near-end Sensor 00 0 0,1 Paper not found by Paper Near-end Sensor 03 3 Paper found b y Paper-end Sensor 00 0 2,.
- 95 - 2.2.8 Paper Detecting Commands ESC c 3 n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Selecting the Paper Sensor valid for a Paper-end signal output [Code.
- 96 - ESC c 4 n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Selecting the Paper Ne ar-end Sensor valid fo r print stop [Code] < 1B > H < 63 > H <.
- 97 - 2.2.9 Panel Switch Commands ESC c 5 n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Enabling/disab ling the panel switches [Code] < 1B > H < 63 &g.
- 98 - 2.2.10 Macro Commands GS : CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Starting/ending macro d efinition [Code] < 1D > H < 3A > H [Outline] [The specification which i s common to the model] Specifying starting/ending m acro definition.
- 99 - GS ^ n1 n2 n3 CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Executing the macro [Code] < 1D > H < 5E > H < n1 >< n2 >< n3 > [.
- 100 - 2.2.11 Cutter Commands ESC i CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Full cutting of paper [Code] < 1B > H < 69 > H [Outline] [The specification which i s common to the model] Execut es full cutti ng of paper.
- 101 - ESC m CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Partial cutting of paper [Code] < 1B > H < 6D > H [Outline] [The specification which i s common to the model] Executes partial cutting of p aper.
- 102 - GS V m ・・・ (1) GS V m n ・・・ (2) CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Cutting the pa per [Code] (1) < 1D > H < 56 > H <.
- 103 - 2.2.12 Bar Code Commands GS H n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Selecting of pri nting position of HRI charact ers [Code] < 1D > H <.
- 104 - GS f n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Selecting the font of HRI characters [Code] < 1D > H < 66 > H < n > [Range] 0 ≦ n ≦ 2 、 48 ≦ n ≦ 50 [Outline] [The specification which i s common to the model] Selecting the font of HRI characters in prin ting bar code.
- 105 - GS h n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying the height of th e bar code [Code] < 1D > H < 68 > H < n > [Range] 1 ≦ n ≦ 255 [Outline] [The specification which i s common to the model] Selecting bar code height.
- 106 - (1)GS k m [d1...dk] NUL (2)GS k m n [d1...dn] CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Printing the ba r code [Code] (1) < 1D > H < 6B > .
- 107 - [Caution] For (1): • This comman d ends with a NULL code. • For UPC -A or UPC-E, the bar code is printe d when 12 bytes of bar code data have been entered , and the subsequent data is handled as nor mal data.
- 108 - [Description of Bar Codes] UPC-A This bar code, consisting of numerals only, ha s a fixed length of 12 columns; a 11- column number entered fr om the host or ap plication sof tware plus a check digit (12th column) automatically calculated inside the p rinter.
- 109 - CODE93 This bar code, consisting of alph anumeric and cont rol character s, has a variable le ngth of columns. Th e HRI character string is prec eded and follow ed by a “ ￭ ” ch aracter.
- 110 - CODE128 This bar code consists of 103 bar code charac ters and three code sets, en abling 128 ASCII code characters to be printed. It has a variable l ength of colum ns. • Code set A ASCII characters 00H - 5FH can be represented. • Code set B ASCII characters 20H - 7FH can be represented.
- 111 - GS w n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying the horiz ontal size (magnificati on) of bar code [Code] < 1D > H < 77 > H < n > [Range] 2 ≦ n ≦ 6 [Outline] [The specification which i s common to the model] Selecting bar code width.
- 112 - 2.2.13 Commands for Non-volatile Memory GS ( C pL pH m fn b [c1 c2][d1...dk] CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Editing user NV m emory [Outlin.
- 113 - fn=0 、 48 ： Function 0 Erasing Specified Record GS ( C pL pH m fn b kc1 kc2 [Code] < 1D > H < 28 > H < 43 > H < pL >< pH >< m >< fn >< b > [.
- 114 - fn=2 、 50 ： Function 2 Sen ding Data St ored in Specified Record GS ( C pL pH m fn b c1 c2 [Code] < 1D > H < 28 > H < 43 > H < pL >< pH >< m >< fn &g.
- 115 - fn=3 、 51 ： Function 3 Sending Use Amo unt GS ( C pL pH m fn b [Code] < 1D > H < 28 > H < 43 > H < pL >< pH >< m >< fn >< b > [Range] (pL+pH.
- 116 - fn=5 、 53 ： Function 5 Sending Key Code List of Stored Record GS ( C pL pH m fn b [Code] < 1D > H < 28 > H < 43 > H < pL >< pH >< m >< fn >< b .
- 117 - fn=6 、 54 ： Function 6 Erasing All User NV Memory Area in a Lump GS ( C pL pH m fn b [d1 d2 d3] [Code] < 1D > H < 28 > H < 43 > H < pL >< pH >< m >< .
- 118 - GS ( L pL pH m fn [parameter] GS 8 L p1 p2 p3 p4 m fn [parameter] CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying graphics data [Code] < 1D &g.
- 119 - fn=0 、 48 ： Function 48 Sendi ng NV Graphics Memory Capacity GS ( L pL pH m fn [Code] < 1D > H < 28 > H < 4C > H < pL >< pH >< m >< fn > [Range] (.
- 120 - fn=3 、 51 ： Function 51 Sendi ng the Remaining A mount of NV Graphics Memory GS ( L pL pH m fn [Code] < 1D > H < 28 > H < 4C > H < pL >< pH >< m >< f.
- 121 - fn=64 ： Function 64 Sending Key Code List of Defined NV Graphics GS ( L pL pH m fn d1 d2 [Code] < 1D > H < 28 > H < 4C > H < pL >< pH >< m >< fn >&l.
- 122 - fn=65 ： Function 65 Erasing All Data of NV Graphics in a Lu mp GS ( L pL pH m fn d1 d2 d3 [Code] < 1D > H < 28 > H < 4C > H < pL >< pH >< m >< fn >&.
- 123 - fn=67 ： Function 67 Defining Raster Type Graphics Data to NV Memory GS ( L pL pH m fn a kc1 kc2 b xL xH yL yH [c d1...dk]1...[c d1...dk]b [Code] < 1D > H < 28 > H < 4C > H .
- 124 - fn=69 ： Function 69 Printing Specified Graphics GS ( L pL pH m fn kc1 kc2 x y [Code] < 1D > H < 28 > H < 4C > H < pL >< pH >< m >< fn >< kc1 >.
- 125 - fn=112 ： Function 112 Storing Raster Type Graphics Data to Print Buffer GS ( L pL pH m fn a bx by c xL xH yL yH d1...dk [Code] < 1D > H < 28 > H < 4C > H < pL >< p.
- 126 - GS g 0 m nL nH CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Initializing maintenance counter [Code] < 1D > H < 67 > H < 30 > H < m &.
- 127 - GS g 2 m nL nH CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Sending maintenance counter [Code] < 1D > H < 67 > H < 32 > H < m >&l.
- 128 - FS p n m CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Printing the do wnload NV bit image s [Code] < 1C > H < 70 > H < n >< m > [.
- 129 - [Sample Program] GOSUB SETNV LPRINT CHR$(&H1C); “p”; CHR$(1); CHR$(0); DA T A &H00, &H00, &H00, &H00, &H07 , &HF0 LPRINT CHR$(&HA); DA T A &H1E, &H7.
- 130 - FS q n [xL xH yL yH d1...dk]1...[xL xH yL yH d1...dk]n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Defining the downl oad NV bit image [Code] < 1C &g.
- 131 - • The definition data of one N V bit image consi sts of [xL xH yL yH d1… dk]. Th erefore, when only one NV b it image is defined, n = 1; the data group [x L xH yL yH d1… dk] is mani pula.
- 132 - 2.2.14 Kanji Control Commands FS ! n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Collectively setting Kanji print mode [Code] < 1C > H < 21 > H < n > [Range] 0 ≦ n ≦ 255 [Outline] [The specification which i s common to the model] Collectively sets Kanji prin t mode.
- 133 - FS & CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting Kanji mode [Code] < 1C > H < 26 > H [Outline] [The specification which i s common to the model] Sets Ka nji mode. Japanese Kanji specifications: This command is invalid when Kanji code sy stem is Shift JIS.
- 134 - FS - n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting/canceling Kanji underl ine [Code] < 1C > H < 2D > H < n > [Range] 0 ≦ n ≦ 2 、 48 ≦ n ≦ 50 [Outline] [The specification which i s common to the model] Sets or cancel s Kanji underline.
- 135 - FS . CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Canceling Kanji mode [Code] < 1C > H < 2E > H [Outline] [The specification which i s common to the model] Cancels K anji mode. Japanese Kanji specifications: This command is invalid when Kanji code sy stem is Shift JIS.
- 136 - FS 2 a1 a2 [d]k CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Defining external ch aracter [Code] < 1C > H < 32 > H < a1 > H < a2 >.
- 137 - [Sample Program] LPRINT CHR$(&H1C);" &"; DA T A &H00, &H00, &H00, &H00 , &H00, &H00 GOSUB SET CHR DA T A &H00, &H00, &H60, &H00, &.
- 138 - FS C n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Selecting Kanji code system [Code] < 1C > H < 43 > H < n > [Range] 0 ≦ n ≦ 1 、 48 ≦ n ≦ 49 [Outline] [The specification which i s common to the model] Selects K anji code system.
- 139 - [Sample Program] [Print Results] LPRINT CHR$(& H1C);"&"; LPRINT CHR$(&H1C);"C"; CHR$(0); 漢字 ← Shift JIS code system prin ting 漢字 ← JIS code sy stem .
- 140 - FS S n1 n2 CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting Kanji space amou nt [Code] < 1C > H < 53 > H < n1 >< n2 > [Range].
- 141 - FS W n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting/canceling fou r times enlargement of Kanji [Code] < 1C > H < 57 > H < n > [Range] 0 ≦ n ≦ 255 [Outline] [The specification which i s common to the model] Sets or cancel s four times enlargemen t of Kanji.
- 142 - FS ( A pL pH fn […] CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting font attribute o f Kanji [Outline] Setting Kanji font attribute m eans execution of pr ocessing for Kanji font attribute by the value of “fn” specified.
- 143 - 2.2.15 Black Mark Control Commands GS FF CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Printing and ejecting Black mark p aper/ label paper [Code] < 1D.
- 144 - GS A m n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Correcting the l eader position of Bl ack mark paper / label paper [Code] < 1D > H < 41 &g.
- 145 - GS C 0 m n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting the numbering print mode [Code] < 1D > H < 43 > H < 30 > H < m >&.
- 146 - GS C 1 n1 n2 n3 n4 n5 n6 CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting the numbering counter mode (A) [Code] < 1D > H < 43 > H < 31.
- 147 - GS C 2 n1 n2 CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting the numbering counter [Code] < 1D > H < 43 > H < 32 > H < n1 >&.
- 148 - GS C ; n1 ; n2 ; n3 ; n4 ; n5 ; CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting the numbering counter mode (B) [Code] < 1D > H < 43 > H .
- 149 - GS c CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Print the counter [Code] < 1D > H < 63 > H [Outline] [The specification which i s common to the model] This command prints the serial number counter data.
- 150 - GS l n1L n1H n2L n2H CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting the Black mark/ label l ength [Code] < 1D > H < 6C > H < n1L >.
- 151 - GS p n CT-S280 CT-S300 CT-S2000 CT-S4000 BD 2-2220 CT-S310 support model PMU2XXX [Function] Changing paper type [Code] < 1D > H < 7 0> H [Range] 0 ≦ n ≦ 255 n=0 specify receipt paper n=1 specify black mark paper n=2 specify label p aper [Outline] [The specification which i s common to the model] • Switches paper.
- 152 - 2.2.16 Printer Function Setting Commands GS ( D pL pH m [a1 b1]...[ak bk] CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Enabling or disabling real-time co.
- 153 - GS ( E pL pH fn […] CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Printer function setting command [Outline] [The specification which i s common to the .
- 154 - fn=1 ： Function 1 Transferring to Printer Function Setting Mode GS ( E pL pH fn d1 d2 [Code] < 1D > H < 28 > H < 45 > H < pL >< pH >< fn >< d1 ><.
fn=3 ： Function 3 Setting Me mory Switch Value [Caution] [The specific ation whic h depend on th e model] [Outline] [The specification which i s common to the model] [Code] < 1D > H < 28 &g.
CT-S280 • Setting memory switch 3 (a = 3) • Setting memory with 1 (a = 1) n b (Set Value) Function n b (Set Value) Function 48 (Default) Reports the power on. 1 48 (Default) Reserve 1 49 Does not report power on. 2 48 (Default) Reserve 48 (Default) Sets input buffer capacity to 4K bytes.
CT-S300 • Setting memory switch 3 (a = 3) n b (Set Value) Function • Setting memory with 1 (a = 1) 48 (Default) After clearing cutter error, can be restored by Feed SW. n b (Set Value) Function 1 49 After clearing cutter error, cannot be restored by Feed SW.
CT-S300 • Setting memory switch 4 (a = 4) n b (Set Value) Function At the selection of Black mark paper, disables auto end-measurement. 48 (Default) 1 At the selection of Black mark paper, enables auto end-measurement.
CT-S2000 • Setting memory with 1 (a = 1) • Setting memory switch 3 (a = 3) n b (Set Value) Function n b (Set Value) Function 48 (Default) Reports the power on. 48 (Default) After clearing cutter error, can be restored by Feed SW. 1 1 49 Does not report power on.
CT-S2000 • Setting memory switch 5 (a = 5) n B (Set Value) Function 48 (Default) Buzzer soun d enabled 1 Buzzer sound disabled 49 48 (Default) Basic calculation pitch (180 dpi / 360 dpi) 2 49 Basic .
CT-S4000 • Setting memory with 1 (a = 1) • Setting memory switch 3 (a = 3) n b (Set Value) Function n b (Set Value) Function 48 (Default) Reports the power on. 48 (Default) After clearing cutter error, can be restored by Feed SW. 1 1 49 Does not report power on.
CT-S4000 • Setting memory switch 4 (a = 4) • Setting memory switch 5 (a = 5) n b (Set Value) Function n B (Set Value) Function 48 (Default) At the selection of Black mark paper/ label paper, disables auto end-measurement.
BD2-2220 • Setting memory with 1 (a = 1) • Setting memory switch 3 (a = 3) n b (Set Value) Function n b (Set Value) Function 48 (Default) Reports the power on. 48 (Default) After clearing cutter error, can be restored by Feed SW. 1 1 49 Does not report power on.
CT-S310 • Setting memory switch 3 (a = 3) • Setting memory with 1 (a = 1) n b (Set Value) Function n b (Set Value) Function 48 (Default) Reports the power on. 48 (Default) After clearing cutter error, can be restored by Feed SW. 1 1 49 Does not report power on.
CT-S310 • Setting memory switch 4 (a = 4) n b (Set Value) Function At the selection of Black mark paper, disables auto end-measurement. 48 (Default) 1 At the selection of Black mark paper, enables auto end-measurement.
PMU2XXX • Setting memory switch 3 (a = 3) n b (Set Value) Function • Setting memory with 1 (a = 1) 48 (Default) After clearing cutter error, can be restored by Feed SW. n b (Set Value) Function 1 49 After clearing cutter error, cannot be restored by Feed SW.
- 167 - Setting memory switch 5 (a = 5) n b (Set Value) Function 1 48 (Default) Reserved 2 48 (Default) Reserved 3 48 (Default) Reserved 4 48 (Default) Reserved 5 48 (Default) Reserved 48 It is priori.
- 168 - fn=4 ： Function 4 Sending the Set Memory Switch Value GS ( E pL pH fn a [Code] < 1D > H < 28 > H < 45 > H < pL >< pH >< fn >< a > [Range] （ pL ＋.
fn=5 ： Function 5 Setting Customized Value [Caution] • This functi on operates only i n printer function setting m ode. [Outline] [The specification which i s common to the model] [Range] 4 ≦ (p.
CT-S280 • a = 5: Sets printing density to the level specified by (nL+nHx256). • a = 116: Sets the paper specified by (nL+nHx256). (nL+nHx256) Printing Density (nL+nHx256) Paper 65530 70% 1 (Default) Specified single color paper.
CT-S300 / CT-S310 • a = 3: Sets paper width to the size specified by (nL+nHx256). • a = 6: Sets printing speed to the value specified by (nL+nHx256).
CT-S300 / CT-S310 • a=222: Head margin set by the val ue selected by (nL+nHx256). • a = 202: Controls input buffer full Busy with the value selected by (nL+nHx256) and controls Busy with output/cancel ti ming (remaining capacity).
CT-S2000 • a = 1: Sets the user NV memory cap acity to the size specified by (nL+nH×256). • a = 5: Sets printing density to the level specified by (nL+nHx256).
CT-S2000 • a=212 ： Selects DMA (Direct Memory Access) control of serial communication specified by (nL+nHx256). • a = 116: Sets the paper specified by (nL+nHx256).
CT-S2000 • a=221: Sets the maximum length of black m ark page with the value selected by (nL+nHx256). • a=225: Sets head distance wi th the value selected by (nL+nHx256).
CT-S4000 • a = 1: Sets the user NV memory cap acity to the size specified by (nL+nH×256). • a = 5: Sets printing density to the level specified by (nL+nHx256).
CT-S4000 • a=212 ： Selects DMA (Direct Memory Access) control of serial communication specified by (nL+nHx256). • a = 116: Sets the paper specified by (nL+nHx256).
BD2-2220 • a = 201: Outputs ACK to the position specified by (nL+nHx256). • a = 5: Sets printing density to the level specified by (nL+nHx256). (nL+nHx256) Printing Density (nL+nHx256) ACK Output .
PMU2XXX • a = 201: Outputs ACK to the position specified by (nL+nHx256). • a = 5: Sets printing density to the level specified by (nL+nHx256). (nL+nHx256) Printing Density (nL+nHx256) ACK Output P.
• a=225: Sets head distance wi th the value selected by (nL+nHx256). 1 ≦ (nL+nH×256) ≦ 255 Initial value: 56 dots Unit: 1 dot - 180 - • a=223 ： Sets black mark bottom margin with the am ount selected by (nL+nHx256). • a=221: Sets the maximum length of black m ark page with the value selected by (nL+nHx256).
fn=6 ： Function 6 Sending the Set Customized Val ue [Range] (pL+pH×256)=2 ： (pL=2 、 pH=0) [Code] < 1D > H < 28 > H < 45 > H < pL >< pH >< fn >< a > [Outline] [The specification which i s common to the model] GS ( E pL pH fn a fn=6 • Configuration of customized value No.
- 182 - CT-S280 • a = 5: When print density is specified Setting Status Sending Data Stored Value Print Density 1st By te 2nd Byte 3rd Byte 4th Byte 5th Byte 65530 70% 54(“6”) 53(“5”) 53(“.
- 183 - CT-S300 / CT-S310 • a = 3: When paper width is specified Setting Status Sending Data Stored Value Paper Width 1st Byte 2nd Byte 3rd Byte 4th Byte 5th Byte 1 58mm 49(“1”) ― ― ― ― .
- 184 - CT-S300 / CT-S310 • a = 201: When ACK output position is specified Setting Status Sending Data Stored Value ACK Output Position 1st By te 2nd Byte 3rd Byte 4th Byte 5th Byte 1 ACK -in-Busy 4.
- 185 - CT-S2000 • a = 1: When user NV memory capacity is specified Setting Status Sending Data Stored Value Memory Capacity 1st Byte 2nd Byte 3rd Byte 4th Byte 5th Byte 1 1K bytes 49(“1”) ― .
- 186 - CT-S2000 • a = 116: When kind of paper is specified Setting Status Sending Data Stored Value Print Control 1st Byte 2nd Byte 3rd Byte 4th Byte 5th Byte 1 Single-color paper 49(“1”) ― .
CT-S2000 • a=222: When head margin is sp ecified Setting Status Sending Data Stored Value Head Margin 1st Byte 2nd Byte 3rd Byte 4th Byte 5th Byte 0 0dot 49(“1”) 48(“0”) 48(“0”) 48(“0.
- 188 - CT-S4000 • a = 1: When user NV memory capacity is specified Setting Status Sending Data Stored Value Memory Capacity 1st Byte 2nd Byte 3rd Byte 4th Byte 5th Byte 1 1K bytes 49(“1”) ― .
CT-S4000 • a=213 ： When the flow control of virtual COM is specified. • a = 116: When kind of paper is specified Setting Status Sending Data Setting Status Sending Data Stored Value Stored Value.
- 190 - BD2-2220 • a = 5: When print density is specified Setting Status Sending Data Stored Value Print Density 1st By te 2nd Byte 3rd Byte 4th Byte 5th Byte 65530 70% 54(“6”) 53(“5”) 53(.
- 191 - PMU2XXX • a = 5: When print density is specified Setting Status Sending Data Stored Value Print Density 1st By te 2nd Byte 3rd Byte 4th Byte 5th Byte 65530 70% 54(“6”) 53(“5”) 53(“.
- 192 - PMU2XXX • a=220: When maximum black mar k width is specified Setting Status Sending Data Stored Value Maximum B.M Width 1st By te 2nd Byte 3rd Byte 4th Byte 5th Byte 0 0dot 49(“1”) 48(.
- 193 - fn=7 ： Function 7 Copying User-defined Page GS ( E pL pH fn a d1 d2 [Code] < 1D > H < 28 > H < 45 > H < pL >< pH >< fn >< a >< d1 >< d2 >.
- 194 - Work Area fn=8 ： Function 8 Defining Data by the Colu mn Format to Character Code Page of GS ( E pL pH fn y c1 c2 [xd1...d(y×x)]k [Code] < 1D > H < 28 > H < 45 > H < pL >< pH >< fn >< y >< c1 >< c2 > [ < x >< d1 > .
- 195 - Work Area fn=9 ： Function 9 Defining Data in the Raster Format to the C haracter Code Page of GS ( E pL pH fn x c1 c2 [y d1...d(x×y)]k [Code] < 1D > H < 28 > H < 45 > H < pL >< pH >< fn >< x >< c1 >< c2 > [ < y >< d1 > .
- 196 - fn=10 ： Function 10 Erasing Data of Charac te r Code Page Data in Work Area GS ( E pL pH fn c1 c2 [Code] < 1D > H < 28 > H < 45 > H < pL >< pH >< fn ><.
- 197 - fn=11 ： Function 11 Setting Communication Conditions GS ( E pL pH fn a d1...dk [Code] < 1D > H < 28 > H < 45 > H < pL >< pH >< fn >< a >< d1 > .
- 198 - fn=12 ： Function 12 Sending the Set Communication Conditions GS ( E pL pH fn a [Code] < 1D > H < 28 > H < 45 > H < pL >< pH >< fn >< a > [Range] (pL.
- 199 - State at Shipment fn=255: Function 255 Setting A ll Contents Set by Printer Fu nction Setting Mode to the GS ( E pL pH fn a [Code] < 1D > H < 28 > H < 45 > H < pL ><.
- 200 - GS ( K pL pH fn m CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Selecting print control meth od [Outline] [The specification which i s common to the model] Executes the setting related to the print cont rol specified by the value of “fn”.
- 201 - fn=49 ： Function 49 Setting Printing Density GS ( K pL pH fn m [Code] < 1D > H < 28 >Ｈ< 4B > H < pL >< pH >< fn >< m > [Range] (pL+pH×256)=2 ： .
- 202 - fn=50 ： Function 50 Setting Printing Speed GS ( K pL pH fn m [Code] < 1D > H < 28 > H < 4B > H < pL >< pH >< fn >< m > [Range] (pL+pH×256)=2(pL=2 .
- 203 - fn=97 ： Function 97 Setting Number of Divisions for Head C onducting GS ( K pL pH fn m [Code] < 1D > H < 28 > H < 4B > H < pL >< pH >< fn >< m > [Ra.
- 204 - GS ( M pL pH fn m CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Customizing the printer [Outline] [The specificatio n which depend on the model] Executes processi ng related to escape/recovery of th e va lue set in the work ar ea or the data defined by various kinds of command .
- 205 - fn=1 、 49 ： Function 1 Copies the set value stored in work area to the storage area GS ( M pL pH fn m [Code] < 1D > H < 28 > H < 4D > H < pL >< pH >< fn &g.
- 206 - initialization to be valid o fn=3 、 51 ： Function 3 Specifies the auto load ing function of the set value at r invalid GS ( M pL pH fn m [Code] < 1D > H < 28 > H < 4D > H.
- 207 - GS ( N pL pH fn m CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Designating font attribute [Outline] [The specific ation which depend on t he model] Executes proce ssing of font attribute by the specified fn valu e.
- 208 - 2.2.17 2-dimensional code Commands GS ( k pL pH cn fn [parameter] CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Setting and printing 2-dimensional cod e [.
- 209 - fn=65 ： F u n ct i o n 6 5 Setting the number of digits of PDF417 GS ( k pL pH cn fn n [Code] < 1D > H < 28 > H < 6B > H < pL >< pH >< cn >< fn ><.
- 210 - fn=67 ： F u n ct i o n 6 7 Setting module width of PDF417 GS ( k pL pH cn fn n [Code] < 1D > H < 28 > H < 6B > H < pL >< pH >< cn >< fn >< n >.
- 211 - fn=69 ： F u n ct i o n 6 9 Setting e rror correction level of PDF417 GS ( k pL pH cn fn m n [Code] < 1D > H < 28 > H < 6B > H < pL >< pH >< cn >< fn &g.
- 212 - fn=70 ： F u n c t i o n 7 0 Setting Options for PDF417 GS ( k pL pH cn fn m [Code] < 1D > H < 28 > H < 6B > H < pL >< pH >< cn >< fn >< m > [R.
- 213 - storage area fn=81 ： F u n c t io n 8 1 Printing 2-dimensional co de data in 2-dimensional code data GS ( k pL pH cn fn m [Code] < 1D > H < 28 > H < 6B > H < pL ><.
- 214 - code data storage area fn=82 ： F u n c ti o n 8 2 Sending the size of 2-di mensional code data in 2-dimensional GS ( k pL pH cn fn m [Code] < 1D > H < 28 > H < 6B > H < .
- 215 - fn=65 ： Function 165 Specifying QRCode model GS ( k pL pH cn fn n1 n2 [Code] < 1D > H < 28 > H < 6B > H < pL >< pH >< cn >< fn >< n1 >< n2 .
- 216 - fn=69 ： Function 169 S e t t i n g Q RC o d e e r r o r co r r e c t i on l e v e l GS ( k pL pH cn fn n [Code] < 1D > H < 28 > H < 6B > H < pL >< pH >< cn &.
- 217 - data storage area fn=81 ： Function 181 P r i n t i n g 2 - d i m e n s i on a l c o d e d a t a i n 2 - d i m e ns i o n a l c o d e GS ( k pL pH cn fn m [Code] < 1D > H < 28 > H.
- 218 - 2-dimensional code da fn=82 ： Function 182 S e n d i n g th e s i z e o f 2 - d i m e n s i on a l c o d e d a t a i n ta storage area GS ( k pL pH cn fn m [Code] < 1D > H < 28 >.
- 219 - 2.2.18 Other Commands DLE ENQ n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Real-time r equest to print er [Code] < 10 > H < 05 > H < n &.
- 220 - DLE DC4 fn m t （ Specification of fn = 1 ） CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Outputting specified p ulse in real-tim e [Code] < 10 >.
- 221 - DLE DC4 fn d1...d7 （ Specification of fn = 8 ） CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Buffer clear [Code] < 10 > H < 14 > H < fn.
- 222 - ESC = n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Data input control [Code] < 1B > H < 3D > H < n > [Range] 0 ≦ n ≦ 255 [Outline] [The specificatio n which depend on the model] • Selecting equipmen t for which data input from the host is valid.
- 223 - ESC @ CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Initializing the printer [Code] < 1B > H < 40 > H [Outline] [The specificatio n which depend on the model] Clears data stored in the print buffer and brings v a rious settings to the init ial state (Def au lt state) .
- 224 - ESC L CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Selecting PAGE MODE [Code] < 1B > H < 4C > H [Outline] [The specificatio n which depend on the model] Switc hes from STA NDARD MODE t o PAGE MODE.
- 225 - ESC S CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Selecting STANDARD MO DE [Code] < 1B > H < 53 > H [Outline] [The specificatio n which depend on the model] Switches from PAGE MODE to STANDARD MODE.
- 226 - ESC p m n1 n2 CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Generating the specified pulses [Code] < 1B > H < 70 > H < m >< n1 >&l.
- 227 - GS ( A pL pH n m CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Execution of test printi ng [Code] < 1D > H < 28 > H < 41 > H < pL >.
- 228 - GS I n CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Caution] • Under DTR/D SR control, the printer send s the printer ID after verify ing that the host is ready .
CT-S280 n Type of Printer ID Specification Value (Hex.) • Sends printer information specified by n=65 or more. Hex. Number of Data 1 、 49 CT -S280 31 Model ID Header 5FH 1 2 、 50 Type ID Refer to table “Type ID” below 20H ～ 7FH Data Subject to item to be responded 3 、 51 ROM version ID Differs by ROM version.
CT-S300 / CT-S310 • Printer information config uration on and after transmitted n=65 is shown below. n Type of Printer ID Specification Value (Hex.) Kind of Printer Information 1 、 49 Model ID CT -S300,CT -S310 35 n Information 2 、 50 Type ID Refer to table “Type ID” below 65 Firmware version Differs by firmware version.
CT-S2000 • Printer information config uration on and after transmitted n=65 is shown below. n Type of Printer ID Specification Value (Hex.) 1 、 49 Model ID CT -S2000 51 Kind of Printer Information Information n 2 、 50 Type ID Refer to table “Type ID” below 3 、 51 ROM version ID Differs by ROM version.
CT-S4000 n Type of Printer ID Specification Value (Hex.) • Printer information config uration on and after transmitted n=65 is shown below. 1 、 49 CT -S4000 55 Model ID Kind of Printer Information 2 、 50 Type ID Refer to table “Type ID” below n Information 3 、 51 ROM version ID Differs by ROM version.
BD2-2220 n Type of Printer ID Specification Value (Hex.) DSW If n = 112 is specified: 1 、 49 Model ID BD2-2220 59 Bit Function Hex. Decimal Dip switch [DSW5] is OFF 2 、 50 Type ID Refer to table “Type ID” below 00 0 0 3 、 51 ROM version ID Differs by ROM version.
- 234 - PMU2XXX n Type of Printer ID Specification Value (Hex.) 1 、 49 Model ID PMU2XXX 3D 2 、 50 Type ID Refer to table “Type ID” below 3 、 51 ROM version ID Differs by ROM version.
- 235 - GS P x y CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Specifying the basic calculati on pitch [Code] < 1D > H < 50 > H < x >< y >.
- 236 - ESC RS CT-S280 CT-S300 CT-S2000 CT-S4000 BD2-2220 CT-S310 support model PMU2XXX [Function] Sound buzzer [Code] < 1B > H < 1E > H [Outline] [The specificatio n which depend on the model] Sound the buzzer for 200 ms. [Caution] This command is buffe red before execution.
- 237 - 3. CHARACTER CODE TABLE 3.1 Code Page 3.1.1 Codepage 00H to 7FH & PC4 37(USA 、 Europe Standard) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p Ç É á ░ └ ╨ α ≡ 1 XON ! 1 .
- 238 - 3.1.2 Codepage 00H to 7FH & Kat akana 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p ▁ ┴S P－タ ミ ═ × 1 XON ! 1 A Q a q ▂ ┬ º ア チ ム ╞ 円 2 " 2 B R b r .
- 239 - 3.1.3 Codepage 00H to 7FH & PC850(Multilingual) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p Ç É á ░ └ ð Ó ― 1 XON ! 1 A Q a q ü æ í ▒ ┴ Ð β ± 2 " 2 B R b .
- 240 - 3.1.4 Codepage 00H to 7FH & PC8 60(Portuguese) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p Ç É á ░ └ ╨ α ≡ 1 XON ! 1 A Q a q ü À í ▒ ┴ ╤ β ± 2 " 2 B R b.
- 241 - 3.1.5 Codepage 00H to 7FH & PC8 63(Canadian-French) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p Ç É ￤ ░ └ ╨ α ≡ 1 XON ! 1 A Q a q ü È ´ ▒ ┴ ╤ β ± 2 " 2.
- 242 - 3.1.6 Codepage 00H to 7FH & PC8 65(Nordic) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p Ç É á ░ └ ╨ α ≡ 1 XON ! 1 A Q a q ü æ í ▒ ┴ ╤ β ± 2 " 2 B R b r .
- 243 - 3.1.7 Codepage 00H to 7FH & PC8 52(Easern Europe) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p Ç É á ░ └ đ Ó - 1 XON ! 1 A Q a q ü Ĺ í ▒ ┴ Đ β ” 2 " 2 B R b.
- 244 - 3.1.8 Codepage 00H to 7FH & PC8 57(Russian) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p ΑР а ░ └ ╨ р Ë 1 XON ! 1 A Q a q Б С б ▒ ┴ ╤ с ë 2 " 2 B R b r В.
- 245 - 3.1.9 Codepage 00H to 7FH & PC8 57(Turkish) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p Ç É á ░ └ o ó ― 1 XON ! 1 A Q a q ü æ í ▒ ┴ a β± 2 " 2 B R b r é Æ.
- 246 - 3.1.10 Codepage 00H to 7FH & PC864(ArabiC ).
- 247 - 3.1.11 Codepage 00H to 7FH & Windows Codepage 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p ° À Ð à ð 1 XON ! 1 A Q a q ‘ ¡ ± Á Ñ á ñ 2 " 2 B R b r ¸ ’ ¢ ² Â Ò â ò 3 XOFF # 3 C S c s ƒ “ £ ³ Ã Ó ã ó 4 EOT DC4 $ 4 D T d t ,, ” ¤ ´ Ä Ô ä Ô 5 ENQ % 5 E U e u .
- 248 - 3.1.12 Codepage 00H to 7FH & Thai code 18.
- 249 - 3.2 Internatinal Character Code Table Country 23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E 0 U.S.A ＃ ＄ ＠ [ ╲ ] ^ ' { | } ~ 1 France ＃ ＄ à ° ç § ^ ' é ù è ¨ 2 Germany ＃ ＄ § Ä Ö Ü ^ ' ä ö ö β 3 U.
- 250 - 3.3 Kanji Code Table 3.3.1 JIS non-Kanji S-JIS JIS 0 1 2 3 4 5 6 7 8 9 A B C D E F 813F 2120 、 。 ，．・：；？！゛ ゜ ´ ｀¨ 814F 2130 ＾ ￣＿ ヽ ヾゝゞ〃仝〆〇〇 ―.
- 251 - S-JIS JIS 0 1 2 3 4 5 6 7 8 9 A B C D E F 843F 2720 А Б В Г ДЕЁЖЗИЙ К Л М Н 844F 2730 О П Р С Т У Ф Х Ц Ч Ш Щ Ъ Ы Ь Э 845F 2740 Ю Я 846F 2750 а б в г де.
- 252 - 3.3.2 JIS Kanji Level 1 S-JIS JIS 0 1 2 3 4 5 6 7 8 9 A B C D E F 889E 3020 亜唖 娃 阿哀愛挨姶逢葵茜 穐 悪 握渥 88AE 3030 旭 葦芦 鯵 梓圧斡扱宛姐虻飴 絢 綾 鮎 或.
- 253 - S-JIS JIS 0 1 2 3 4 5 6 7 8 9 A B C D E F 8B9E 3620 供 侠 僑 兇 競 共 凶 協 匡 卿 叫 喬 境 峡 強 8BAE 3630 彊 怯 恐 恭 挟 教 橋 況 狂 狭 矯 胸 脅 興 蕎 郷 8BBE 3.
- 254 - S-JIS JIS 0 1 2 3 4 5 6 7 8 9 A B C D E F 8E9E 3C20 次 滋 治 爾璽痔 磁示而耳自 蒔 辞 汐 鹿 8EAE 3C30 式 識 鴫 竺 軸 宍 雫 七 叱 執 失 嫉 室 悉 湿 漆 8EBE 3C40 .
- 255 - S-JIS JIS 0 1 2 3 4 5 6 7 8 9 A B C D E F 919E 4220 臓 蔵 贈 造促側則即息捉束 測 足 速俗 91AE 4230 属 賊族 続 卒袖 其揃存孫尊損 村 遜 他多 91BE 4240 太 汰詑 .
- 256 - S-JIS JIS 0 1 2 3 4 5 6 7 8 9 A B C D E F 949E 4820 函 箱 硲 箸肇筈 櫨幡肌畑畠 八 鉢 溌 発 94AE 4830 醗 髪 伐 罰 抜 筏 閥 鳩 噺 塙 蛤 隼 伴 判 半 反 94BE 4840 .
- 257 - S-JIS JIS 0 1 2 3 4 5 6 7 8 9 A B C D E F 979E 4E20 痢 裏 裡 里 離陸律率立葎掠 略 劉 流 溜 97AE 4E30 琉 留 硫 粒 隆 竜 龍 侶 慮 旅 虜 了 亮 僚 両 凌 97BE 4E40 .
- 258 - 3.3.3 JIS Kanji Level 2 S-JIS JIS 0 1 2 3 4 5 6 7 8 9 A B C D E F 989E 5020 弌丐 丕 个丱丶丼丿乂乖乘 亂 亅 豫亊 98AE 5030 舒 弍于 亞 亟亠亢亰亳亶从仍 仄 仆 仂 仗.
- 259 - S-JIS JIS 0 1 2 3 4 5 6 7 8 9 A B C D E F 9B9E 5620 屐 屏 孱 屬屮乢屶屹 岌岑岔 妛 岫 岻岶 9BAE 5630 岼 岷 峅 岾 峇 峙 峩 峽 峺 峭 嶌 峪 崋 崕 崗 嵜 9BBE 5640 崟.
- 260 - S-JIS JIS 0 1 2 3 4 5 6 7 8 9 A B C D E F 9E9E 5C20 棔 棧 棕 椶椒椄 棗棣椥棹棠 棯 椨 椪 椚 9EAE 5C30 椣 椡 棆 楹 楷 楜 楸 楫 楔 楾 楮 椹 楴 椽 楙 椰 9EBE 5C40 .
- 261 - S-JIS JIS 0 1 2 3 4 5 6 7 8 9 A B C D E F E19E 6220 癲 癶 癸 發皀皃皈皋 皎皖皓 皙 皚 皰皴 E1AE 6230 皸 皹 皺 盂 盍 盖 盒 盞 盡 盥 盧 盪 蘯 盻 眈 眇 E1BE 6240 眄.
- 262 - S-JIS JIS 0 1 2 3 4 5 6 7 8 9 A B C D E F E49E 6820 茵 茴 茖 茲茱荀茹荐 荅茯茫 茗 茘 莅莚 E4AE 6830 莪 莟 莢 莖 茣 莎 莇 莊 荼 莵 荳 荵 莠 莉 莨 菴 E4BE 6840 萓.
- 263 - S-JIS JIS 0 1 2 3 4 5 6 7 8 9 A B C D E F E79E 6E20 遏 遐 遑 遒逎遉逾遖 遘遞遨 遯 遶 隨遲 E7AE 6E30 邂 遽 邁 邀 邊 邉 邏 邨 邯 邱 邵 郢 郤 扈 郛 鄂 E7BE 6E40 鄒.
- 264 - S-JIS JIS 0 1 2 3 4 5 6 7 8 9 A B C D E F EA9E 7420 堯 槇 遙 瑤 EAAE 7430 EABE 7440 EACE 7450 EADE 7460 EAEE 7470.
- 265 - 4. Memory Switch Memory switch is a function to save th e user sele cted settings into N V memory, where me mory switch setting will be held unless memory switch is changed. Memory switch is changed by manual setting or by command in th e memory switch change mode.
- 266 - 4.1.2 CT-S300 No. Setting OFF ON MSW1-1 Power ON Inf o ● V a l i d N o t s e n d MSW1-2 Buff er Size ● 4 K b y t e s 4 5 b y t e s MSW1-3 Busy Condition ● F u l l / E r r F u l l MSW1- 4.
- 267 - 4.1.3 CT-S2000 No. Setting OFF ON MSW1-1 Power ON Inf o ● V a l i d N o t s e n d MSW1-2 Buff er Size ● 4 K b y t e s 4 5 b y t e s MSW1-3 Busy Condition ● F u l l / E r r F u l l MSW1- .
- 268 - No. Setting Default Set Values MSW7-1 Baud Rate 19200bps 2400bps,4800bps,9600bps,19200bps,38400bps, 57600bps,115200bps MSW7-2 Data Length 8bits 7bits,8bits MSW7-3 Stop Bit 1bit 1bit,2bits MSW7.
- 269 - 4.1.4 CT-S4000 No. Setting OFF ON MSW1-1 Power ON Inf o ● V a l i d N o t s e n d MSW1-2 Buff er Size ● 4 K b y t e s 4 5 b y t e s MSW1-3 Busy Condition ● F u l l / E r r F u l l MSW1- .
- 270 - No. Setting Default Set Values MSW7-1 Baud Rate 19200bps 1200bps,2400bps,4800bps,9600bps,19200bps, 38400bps,57600bps,115200 bps MSW7-2 Data Length 8bits 7bits,8bits MSW7-3 Stop Bit 1bit 1bit,2.
- 271 - 4.1.5 BD2-2220 No. Setting OFF ON MSW1-1 Power ON Inf o ● V a l i d N o t s e n d MSW1-2 Buff er Size ● 4 K b y t e s 4 5 b y t e s MSW1-3 Busy Condition ● F u l l / E r r F u l l MSW1- .
- 272 - 4.1.6 CT-S310 No. Setting OFF ON MSW1-1 Power ON Inf o ● V a l i d N o t s e n d MSW1-2 Buff er Size ● 4 K b y t e s 4 5 b y t e s MSW1-3 Busy Condition ● F u l l / E r r F u l l MSW1- 4.
- 273 - No. Setting Default Set Values MSW7-1 Baud Rate 19200bps 1200bps,2400bps,4800bps,9600bps,19200bps, 38400bps MSW7-2 Data Length 8bits 7bits,8bits MSW7-3 Stop Bit 1bit 1bit,2bits MSW7-4 Parit y .
- 274 - 4.1.7 PMU2XXX No. Setting OFF ON MSW1-1 Power ON Inf o ● V a l i d N o t s e n d MSW1-2 Buff er Size ● 4 K b y t e s 4 5 b y t e s MSW1-3 Busy Condition ● F u l l / E r r F u l l MSW1- 4.
- 275 - No. Setting Default Set Values MSW7-1 Baud Rate 9600bps 1200bp s,2400bps,4800bps,9600bps,19200 bps, 38400bps,57600bps,115200 bps MSW7-2 Data Length 8bits 7bits,8bits MSW7-3 Stop Bit 1bit 1bit,.
- 276 - 4.2 Details of Memory Switches This section describe s the function of memory switch. Some MSW may not be set or some v alues may not be selected depending on the model used. For the MSW and value that can be set or selected with the model you are using, refer to the oper ation manual or the like.
- 277 - ● MSW1-3 ： Busy condition [Outline] Select the condition that p rinter is BUSY . Automatic status send f unction also runs. OFF(0) ON(1) Busy Condition Buff er full/Off - li ne Buffer f ull ON (1) OPERA TION: If receive buf fer is f ull, printer is BUSY .
- 278 - ● MSW1-5 ： CR code [Outline] Select the printer when receiving CR(<0D> H) code. OFF(0) ON(1 ) CR mode Ignor ed LF ON (1) OPERA TION: Select the same op erati on with LF when r eceiving CR cod e. Print data in pri nt buff er and put linef eeds as specif ied.
- 279 - 4.2.2 MSW2 ● MSW2-1 ： Reserved [Fixed to ON(1)] ● MSW2-2 ： Au to-cut ter operation [Outline] Select auto-cutter enable/disable. OFF(0) ON ( １ ) Auto Cutter In valid Valid ON (1) OPERA TION: Auto-cutter enabled OFF (0) OPERA TION: Auto-cutter disabled ● MSW2-3 ： B ufferin g [Outline] Select bufferin g print enable/disable.
- 280 - ● MSW2-4 ： Ful l Columns print [Outline] Select the proc essing if print dat a closes to the end of line or the r ight of print wid th. OFF(0) ON(1 ) Full Col print Line F eed W ait Data ON (1) OPERA TION: If printer recei ves data/com mand exceeding th e full column, printer further waits for print data.
- 281 - ● MSW2-6 ： Pa p er w i dt h [Outline] Select paper width. OFF( ０ ) ON( １ ) Paper width 80mm 58mm ON (1) OPERA TION: Paper width is set 80mm OFF (0) OPERA TION: Paper width i s set 58mm ● MSW2-7 ： Reserved [Fixed to OFF (0)] ● MSW2-8 ： PNE sensor [Outline] Select paper near-e nd enable/disabl e.
- 282 - 4.2.3 MSW3 ● MSW3-1 ： Au to-cutter ret urn [Outline] Select return method from c utter lock error . OFF(0) ON(1 ) Resu m Cttr Err V alid Inv alid ON (1) OPERA TION: Return by command. Afte r removing error ca use, return wi th command <DL E ENQ n>.
- 283 - ● MSW3-4 ： Select ing paper [Outline] Selects either thermal pape r or black mark paper. OFF(0) ON(1) Paper Select Thermal Black Mark Operation at O N (1): Sets black mark paper. Operation at OFF (0): Sets th ermal paper. ● MSW3-5 ： Column Number [Outline] Selects colum n nu mber.
- 284 - ● MSW3-8 ： Cover open during printing [Outline] Select the release method of cover open err or during printing. OFF(0) ON(1) Resu m Open Err Close Command ON (1) OPERA TION: Cover open err or during printing becomes a r eturn allowed error .
- 285 - 4.2.4 MSW4 ● MSW4-1 ： Automat ic length measurement [Outline] In selecting black mark paper , set the enab le/disabl e of automatic length measurem ent. (Black mark/label support model only ） OFF(0) ON(1 ) BM Measure Invalid V alid ON (1) OPERA TION: Automatic length measurement is enabled.
- 286 - ● MSW4-4 ： Pa p er [Outline] Selects the type of paper used. OFF(0) ON(1 ) Paper Thermal roll paper Black mark paper/Label paper O N ( 1 ) O P E R A T I O N : Paper used is limited to black mark paper or label paper. O F F ( 0 ) O P E RA T I O N : Paper used is limited to thermal roll paper.
- 287 - 4.2.5 MSW5 ● MSW5-1 ： B uzzer [Outline] Select the enable/disable of b uzzer . OFF(0) ON(1 ) Buzzer V alid Inv alid ON (1) OPERA TION: Disable buzzer When a n error occ urs or memo ry switch se tting is c hanged manua lly , no buzzer sounds.
- 288 - ● MSW5-5 ： Setting the po wer OFF notif y [Outline] At power OFF , to notify the h ost of the printer power OFF , printer can send to host 3 byte power OFF not if y’s status data ( < 3B > H < 31 > H < 00 > H) . Set to enable/disable f or sending th e power OFF not if y’s status data.
- 289 - 4.2.7 MSW7 ● MSW7-1 ： Baud rate [Outline] Select baud rate whi ch is serial interface communication con dition. Enabled if DSW1 -1 OFF is set [f ol lowing memory switch setting].
- 290 - ● MSW7-6 ： DMA control [Outline] Select the enable/disable of DMA (Direct Memory Access) control. Setting Value DMA control Valid , Inv alid ● MSW7-7 ： VCom flow control [Outline] In MSW5-3, select the flow contr ol when virtual C OM is set.
- 291 - 4.2.8 MSW8 ● MSW8-1 ： Print width [Outline] Select the print width in dots. Setting Value Print Width 832dots, 720dots,660dots,640 dots,576dots,512dots, 436dots,432dots,420dots,384dots,360d ots ● MSW8-2 ： Paper type [Outline] Select the paper type used.
- 292 - 4.2.9 MSW9 ● MSW9-1 ： Code page [Outline] Select the code page. Setting Value Code Pag e PC437 ,K atakana,PC850 ,PC858,PC860,PC8 63, PC865,PC852,PC866,PC8 57 ,WindowsCode, PC864,ThaiCod e18 ● MSW9-2 ： In ternational character [Outline] Select the international char acter .
- 293 - 4.2.10 MSW10 ● MSW10-1 ： Print density [Outline] Select the print density . Setting Value Print Density 70%,75%,8 0%,85%,90 %,95%,100%,105 %, 110%,115%,120% ,125%,130%,135%,140 % ● MSW10-2 ： Print speed [Outline] Select the print speed.
- 294 - 5. APPENDIX 5.1 Explanation on PAGE MODE 5.1.1 Overview The printer has two prin t modes: STANDARD and PAGE. In STANDARD MODE, the p rinter prints or feeds paper each time it recei ves a print or paper feed command .
- 295 - 5.1.3 Mapping of Print Data in the Print Area Print data is m apped in the print area as follows: (1) The print area is set by ESC W. When the printer has fi nished all of the prin t and paper.
- 296 - Mapping d irection Baseline Print area dx, dy x0, y0 2 4 -3 Point A Figure 5-1 Mapping Position for Character Data Double height char acter 24*2-6 42 Bit image nH*256+n ESC * m nL nH 6*8=48 Do.
- 297 - 5.1.4 Example of Using PAGE MODE The following explains specific uses of PAGE MODE . When in PAGE MOD E, the command s are typicall y sent from the host to the printer in the following seq uence: (1) An ESC L puts the prin ter in PAGE MODE. (2) An ESC W specifies the print area.
- 298 - In Figure 4-3, a line feed occurs be tween “lesson” and “Test 1” because the space “ “ next to “lesson” does not fit in the horizontal ran ge of the 200 400 -pitch print area. Th e line feed width confor ms to the value spe cified by a command such as ESC 3.
- 299 - P age mode lesson 2CAN command ABCDEFGHIJKLMNOP QRST1234567890 Print area 400 ( 0 , 0 ) 200 Print Direction Paper Figure 5-4 Example 2: Result of Print Before an FF i s sent (170th line), the f ollowing prog ram code can be adde d to remove part of th e data.
- 300 - P age mode lesson 2CAN command ABCDEF JKLMNOP QRST1234567890 400 ( 0 , 0 ) 200 Paper Print area Print Direction Figure 5-5 Print Result of Adding a Program of Example 3 to Example 2.
- 301 - 5.2 Bidirectional Parallel Interface Overview The interface of the printer i s a Level-1 comp atible device according to I EEE-P1284. It supports the communicati on modes described i n 5.2.1 belo w. 5.2.1 Parallel Interface Communication Mode The parallel interface of the printe r provides three communicati on modes as outlined below.
- 302 - 5.2.2 Interfacing Phases Interfacing in each communication mode is divided into several ph ases. In addition , there is a phase for mode initialization, as well as a phase f or mode switching . Interface sign als may differ i n name and function for differen t modes and different phases.
- 303 - 5.2.3 Negotiation Overview Usually, the printer i s started in Comp atibility mode, wh ich corresponds to the Centronics i nterface phase. When the host intends to swit ch to the Nibble or Byt e mode, it sends a re quest and negoti ates with the prin ter.
- 304 - Precautions (1) The Negoti ation phase is triggered wh en the IEEE 1284 Active signal sent by the host becomes High. (2) In Compatibility m ode, the tim e when the negotiation p rocess begins is , as a general rule, after th e host sets nStrobe to Hig h and then the printer outputs an nA ck pulse.
- 305 - Data Communication f rom Printer to Host Nibble Mode In this mode, dat a is transferr ed between the prin ter and the ho st through th e procedure describ ed below. The steps begi nning from (1) are applicable when th e Ne gotiati on phase has swi tched to the Host Busy Data Available phase.
- 306 - (14) Upon receiving a request for interrupt from the pri nte r, the ho st responds by setting H ostBusy (nA utoFd) t o High. (Event 20) (15) Finally, th e printer responds to the host by set ting AckDataReq (P Error) to Low, and then the host moves to the Host Busy Data Available phase.
- 307 - Byte Mode In this mode, dat a is transferr ed between the prin ter and the ho st through th e procedure describ ed below. The steps begi nning from (1) are applicable when th e Ne gotiati on phase has swi tched to the Host Busy Data Available phase.
- 308 - Device ID The device ID i s a charac ter string that provides th e ID, the type, and other information regarding the printer connected to th e interface.
- 309 - Termination Termination is the process of returning to Compatibility mode from the Ni bble or Byte modes. When performing Terminati on, the host sets the signa ls as follow s: • IEEE 1284 Ac.
- 310 - 5.3 Identification of Send Status Because the status sent from the printer has certain fixed bits , it is possible to iden tify to which command the statu s belongs.
- 311 - If printing of “E” of 2 times vertical (48 dots) is attempted there, 48 dots are not printed in the remaining area of 36 do ts. Therefore, “E” i s printed from next label’s first print position. Here, line feed of “E” must also be included in the calculation of the height of “E”.
- 312 - If printing of image greater than inter-BM distance/label paper length (vertical print area width) is attempted, image is printed in two separated images as sh own below. Barcode, downloaded image, NV image, page mode Image greater than vertical print area of label paper used is printed over the label.
Een belangrijk punt na aankoop van elk apparaat Citizen Systems PMU2XXX (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Citizen Systems PMU2XXX heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Citizen Systems PMU2XXX vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Citizen Systems PMU2XXX leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Citizen Systems PMU2XXX krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Citizen Systems PMU2XXX bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Citizen Systems PMU2XXX kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Citizen Systems PMU2XXX . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
