Gebruiksaanwijzing /service van het product 408525-001 van de fabrikant Compaq
Ga naar pagina of 221
b Main tenan ce and Ser vice Gui de Co mpaq Pr esar i o V2 6 00 Notebook PC Doc ument P art Number : 4085 25- 00 1 Mar ch 2006 This guide is a troubleshooting reference used for maintaining and servicing the computer .
© Copyright 2006 He wlett-Packard De velopment Company , L.P . Microsoft and W indows are U.S. re gistered trademarks of Microsoft Corporation. Intel is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.
Maintenance and S ervice Gui de iii Cont ent s 1 Product Description 1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2 1.2 Resetting the Computer . . . . . . . . . . . . . . . . . . . . . . . 1–4 1.3 Power Management .
i v Maintenance and S ervice Gui de Cont ent s 3 Illustrated Parts Catalog 3.1 Serial Number Location . . . . . . . . . . . . . . . . . . . . . . 3–1 3.2 Computer Major Components . . . . . . . . . . . . . . . . . . 3–2 3.3 Display Assembly Components .
Cont ent s Maintenance and Se rvice Guide v 5 Removal and Replacement Procedures 5.1 Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–2 5.2 Disassembly Sequence Chart . . . . . . . . . . . . . . . . . . 5–3 5.3 Preparing the Computer for Disassembly .
v i Maintenance and S ervice Gui de Cont ent s 6 Specifications A Connector Pin Assignments B Power Cord Set Requirements C Screw Listing D Display Component Recycling Index.
Maintenance and Se rvice Guide 1–1 1 Product Des c ription The Compaq Presario V2600 Notebook PC of fers advanced modularity , Intel® Core Duo and Core Solo processors, and extensi ve multimedia support.
1–2 Maintenance and S ervice Gui de Product Description 1.1 F e a t u r e s ■ The follo wing processors are av ailable, varying b y computer model: ❏ Intel Core Duo T2500 (2.00-GHz) ❏ Intel Core Duo T2400 (1.83-GHz) ❏ Intel Core Duo T2300 (1.
Product Description Maintenance and Se rvice Guide 1–3 ■ Support for ExpressCards ■ External 65-watt A C adapter with 3-wire power cord ■ 6-cell or 12-cell Li-Ion battery pack ■ Stereo speak.
1–4 Maintenance and S ervice Gui de Product Description 1 .2 Reset ting t h e Com pu ter If the computer you are servicing has an unkno wn password, follo w these steps to clear the password. These steps also clear CMOS: 1. Prepare the computer for disassembly (refer to Section 5.
Product Description Maintenance and Se rvice Guide 1–5 1. 3 P o w e r M a n a g e m e n t The computer comes with po wer management features that extend battery operating time and conserv e power .
1–6 Maintenance and S ervice Gui de Product Description 1 .4 External Com ponen ts The external components on the front of the computer are sho wn belo w and described in T able 1-1.
Product Description Maintenance and Se rvice Guide 1–7 Ta b l e 1 - 1 Front Components Item Component Function 1 Speakers (2) Produce stereo sound. 2 Wireless light (select models only) On: An integrated wireless de vice is hardware enab led. 3P o w e r l i g h t ■ On: Computer is turned on.
1–8 Maintenance and S ervice Gui de Product Description The external components on the right side of the computer are sho wn below and described in T able 1-2.
Product Description Maintenance and Se rvice Guide 1–9 Ta b l e 1 - 2 Right-Side Components Item Component Function 1 USB connectors (2) Connect an optional USB device .
1–10 Maintenance and Serv ice Guide Product Description The external components on the rear and left side of the computer are sho wn below and described in T able 1-3.
Product Description Maintenance and S ervice Gui de 1–11 Ta b l e 1 - 3 Rear and Left-Side Components Item Component Function 1 Exhaust ve nt Pro vide airflow to cool internal components. Ä T o pre vent o verheating, do not obstruct vents . User the computer only on a flat, hard surf ace.
1–12 Maintenance and Serv ice Guide Product Description The computer ke yboard component s on the computer are shown belo w and described in T able 1-4.
Product Description Maintenance and S ervice Gui de 1–13 T able 1-4 Ke yboard Components Item Component Function 1 fn ke y Combines with other ke ys to perform system tasks. F or e xample, pressing fn+f7 decreases screen brightness. 2 caps lock ke y Enables caps loc k and tur ns on the caps lock light.
1–14 Maintenance and Serv ice Guide Product Description The computer top components on the computer are sho wn below and described in T able 1-5. T op Components , P ar t 1 Ta b l e 1 - 5 T op Components, Part 1 Item Component Function 1 Caps lock light On: Caps lock is on.
Product Description Maintenance and S ervice Gui de 1–15 3 Wireless button Enables/disab les an inter nal wireless de vice. Wireless light On: an integrated wireless de vice is hardware enab led. 4 P ower button When the computer is ■ Off , press to tur n on the computer .
1–16 Maintenance and Serv ice Guide Product Description The computer top components on the computer are sho wn below and described in T able 1-6. T op Components , P ar t 2.
Product Description Maintenance and S ervice Gui de 1–17 Ta b l e 1 - 6 T op Components, Part 2 Item Component Function 1 T ouchPad horizontal scrolling region Scrolls tow ard left side or ri ght side. 2 T ouchPad Mov es the pointer . 3 T ouchPad light On: T ouchP ad is enabled.
1–18 Maintenance and Serv ice Guide Product Description The external components on the bottom of the computer are sho wn below and described in T able 1-7. Bott om Components Ta b l e 1 - 7 Bottom Components Item Component Function 1 Optical drive Suppor ts an optical disc.
Product Description Maintenance and S ervice Gui de 1–19 4 Exhaust ve nts (4) Provide airflow to cool internal components. Ä T o pre vent o verheating, do not obstruct vents .
1–20 Maintenance and Serv ice Guide Product Description 1. 5 D e s i g n O v e r v i e w This section presents a design ov erview of k ey parts and features of the computer . Refer to Chapter 3, “Illustrated Parts Catalog, ” to identify replacement parts, and Chapter 5, “Remov al and Replacement Procedures, ” for disassembly steps.
Maintenance and Se rvice Guide 2–1 2 T roubleshooting Å W ARNIN G: Only au thori z ed techni ci ans trained b y HP should r epair this equipment . All tr oubleshooting and r e pair pr ocedures ar e detailed to allo w only subas sembly-/module-level r epair .
2–2 Maintenance and S ervice Gui de T roublesh ooting Acce ssing Compute r Setup The information and settings in Computer Setup are accessed from the File, Security , T ools, and Advanced menus. 1. Open Computer Setup by turning on or restarting the computer .
T rouble shooting Maintenance and Se rvice Guide 2–3 4. T o confirm the restoration, press f10 . 5. Select File > Sa ve changes and exit , and then follo w the instructions on the screen. When the computer restarts, the factory settings are restored, and any identif ication information you hav e entered is sav ed.
2–4 Maintenance and S ervice Gui de T roublesh ooting Selectin g from the Securit y Menu Ta b l e 2 - 2 Security Menu Select T o Do This Administrator pass word Enter , change , or delete an HP Administrator pass word. P ow er-on password Enter , change, or delete a pow er-on passw ord.
T rouble shooting Maintenance and Se rvice Guide 2–5 Selectin g from the T ools Menu Ta b l e 2 - 3 To o l s M e n u Select T o Do This HDD Self T est options Run a quick or comprehensive self-test on an y hard drive in the system. Battery Inf or mation View inf or matio n about any batter y packs in the computer .
2–6 Maintenance and S ervice Gui de T roublesh ooting Selec ting from the Adv anced Menu Ta b l e 2 - 4 Adv anced Menu Select T o Do This Language (or press f2 ) Change the Computer Setup language. Boot options ■ Enable/Disab le MultiBoot, which sets a star tup sequence that can include most bootable de vices and media in the system.
T rouble shooting Maintenance and Se rvice Guide 2–7 2.2 T roubleshooting Flo wc har ts Ta b l e 2 - 5 T roubleshooting Flo wcharts Overview Flowchart Description 2.1 “Flowchart 2.1—Initial T roubleshooting” 2.2 “Flowchart 2.2—No Po wer , Part 1” 2.
2–8 Maintenance and S ervice Gui de T roublesh ooting Flowchart Description 2.14 “Flowchart 2.14—No OS Loading, Optical Dr ive” 2.15 “Flowchart 2.15—No Audio , P ar t 1” 2.16 “Flowchart 2.16—No Audio , P ar t 2” 2.17 “Flowchart 2.
T rouble shooting Maintenance and Se rvice Guide 2–9 Flo wch ar t 2. 1—Initi al T roub leshootin g Connecting to network or modem? Begin troubleshooting. Is there power? Is the OS loading? Is there video? (no boot) Is there sound? Beeps, LEDs, or error messages? Keyboard/ pointing device working? Go to “Flowchart 2.
2–10 Maintenance and Serv ice Guide T roublesh ooting Flo wch ar t 2.2—No P o w er , P ar t 1 1. Reseat the power cables in the docking device and at the AC outlet. 2. Ensure the AC power source is active. 3. Ensure that the power strip is working.
T rouble shooting Maintenance and S ervice Gui de 2–11 Flo wc har t 2.3—No P ow e r , P ar t 2 Continued from “Flowchart 2.2—No P ower , Pa r t 1 . ” Visually check for debris in batter y socket and clean if necessary . Done N Y Po we r o n ? Check batter y by recharging it, moving it to another computer , or replacing it.
2–12 Maintenance and Serv ice Guide T roublesh ooting Flo wch ar t 2.4—No P o w er , P ar t 3 Continued from “Flowchart 2.3—No P ower , Pa r t 2 . ” Reseat AC adapter in computer and at pow er so urce . Internal or external AC adapter? Done Done Done Done Po we r o n ? Pow e r o n ? Po we r o n ? Plug directly into AC outlet.
T rouble shooting Maintenance and S ervice Gui de 2–13 Flowc ha r t 2.5 —N o P o wer , P ar t 4 Y N Continued from “Flowchart 2.4—No P ower , Pa r t 3 . ” Reseat loose components and boards and replace damaged items. Open computer . Loose or damaged parts? Y Close computer and retest.
2–14 Maintenance and Serv ice Guide T roublesh ooting Flo wch ar t 2.6—No Video, P ar t 1 A N Stand-alone or docking device? No video. Replace the following one at a time. T est after each replacement. 1. Cable between computer and computer display (if applicable) 2.
T rouble shooting Maintenance and S ervice Gui de 2–15 Flo wch ar t 2.7—No Video, P ar t 2 Y N Continued from “Flowchart 2.6—No Video , Pa r t 1 .
2–16 Maintenance and Serv ice Guide T roublesh ooting F lo wcha rt 2. 8 —N on fu nct i on in g D ock ing De vi ce (if applicable ) Y N Reseat power cord in docking device and power outlet. N Check voltage setting on docking device. Reset monitor cable connector at docking device.
T rouble shooting Maintenance and S ervice Gui de 2–17 Flo wch ar t 2.9—No O peratin g S y s tem (OS) Loading No OS loading from hard drive, go to “Flowchart 2.10—No OS Loading, Hard Drive, P ar t 1. ” Reseat power cord in docking device and power outlet.
2–18 Maintenance and Serv ice Guide T roublesh ooting Flo wc har t 2. 1 0—No OS Loadin g , Hard Drive, Pa r t 1 Go to “Flowchart 2.17—Nonfunctioning Device . ” Y Done N OS not loading from hard drive. Nonsystem disk message? Go to “Flowchart 2.
T rouble shooting Maintenance and S ervice Gui de 2–19 Flowc h ar t 2. 1 1—No OS Loa di n g , H a rd Dr ive, Pa r t 2 Load OS using Operating System disc (if applicable). Continued from “Flowchart 2.10—No OS Loading, Hard Drive, P ar t 1. ” Reseat hard drive.
2–20 Maintenance and Serv ice Guide T roublesh ooting Flo wch ar t 2. 1 2—No OS Loadin g, Hard Driv e, Pa r t 3 Y System files on hard drive? Continued from “Flowchart 2.11—No OS Loading, Hard Drive, P ar t 2. ” Clean virus. Done N Install OS and reboot.
T rouble shooting Maintenance and S ervice Gui de 2–21 Flo wch ar t 2. 1 3—No OS Loadin g , Disk ette Drive Replace the following components individually , retesting after each replacement: ■ Diskette drive ■ System board Done Y N Reseat diskette drive.
2–2 2 Maintenance and Serv ice Guide T roublesh ooting Flo wc har t 2. 1 4—No OS Loa ding , O ptical Driv e Y Done N Bootable disc in drive? Disc in drive? No OS loading from CD-ROM or DVD-ROM drive. Install bootable disc and reboot computer . Go to “Flowchart 2.
T rouble shooting Maintenance and Se rvice Guide 2–2 3 Flo wc har t 2. 1 5—N o Audio, P ar t 1 No audio. N Computer in docking device (if applicable)? Internal audio? Audio? Done Undock Audio? Done T urn up audio internally or externally . Go to “Flowchart 2.
2–2 4 Maintenance and Serv ice Guide T roublesh ooting Flo wc har t 2. 1 6—No Audio, P ar t 2 YN Continued from “Flowchart 2.15—No Audio , Pa r t 1 . ” Reload audio drivers. Audio driver in OS configured? Audio? Y Y Y N N N Correct drivers for program? Connect to external speaker .
T rouble shooting Maintenance and Se r v ice Guide 2–2 5 Flo wch ar t 2. 1 7—Nonfun c tioning Dev ice Done Any physical device detected? Y N Unplug the nonfunctioning device from the computer and inspect cables and plugs for bent or broken pins or other damage.
2–2 6 Maintenance and Serv ice Guide T roublesh ooting Flo wch ar t 2. 1 8—Nonfunc tionin g K e yboard Y N Keyboard operating properly? Keyboard not operating properly . External device works? Replace system board. Replace system board. Connect computer to good external keyboard.
T rouble shooting Maintenance and Se rvice Guide 2–2 7 Flo wch ar t 2. 1 9—N onfunc tioning P ointin g De vice Y N Pointing device not operating properly . External device works? Replace system board. Replace system board. Connect computer to good external pointing device.
2–2 8 Maintenance and Serv ice Guide T roublesh ooting Flo wch art 2.20—N o Net wor k/Modem Conne ction Y Disconnect all power from the computer and open. No network or modem connection. N Done Digital line? Network or modem jack active? Replace jack or have jack activated.
Maintenance and Se rvice Guide 3–1 3 I llustra ted P ar ts C a talog This chapter provides an illustrated parts breakdo wn and a reference for spare part numbers and option part numbers.
3–2 Maintenance and S ervice Gui de Illustr ated P arts Catalog 3.2 Comp uter M ajor Com ponents Com pu te r Ma jor Components.
Illustr ated P arts Catalog Maintenance and Se rvice Guide 3–3 Ta b l e 3 - 1 Spare P ar ts: Computer Major Components Item Description Spare P ar t Number 1 Display assemb lies (include wireless antenna transceivers and cables) 14.0-inch, WXGA, SV A with BrightView 14.
3–4 Maintenance and S ervice Gui de Illustr ated P arts Catalog Com pu te r Ma jor Components.
Illustr ated P arts Catalog Maintenance and Se rvice Guide 3–5 Ta b l e 3 - 1 Spare P ar ts: Computer Major Components (Continued) Item Description Spare P ar t Number 7 Processor s (include ther mal pad) Intel Core Duo T2500 (2.00-GHz) Intel Core Duo T2400 (1.
3–6 Maintenance and S ervice Gui de Illustr ated P arts Catalog Com pu te r Ma jor Components.
Illustr ated P arts Catalog Maintenance and Se rvice Guide 3–7 T able 3-1 Spare P ar ts: Computer Major Components (Continued) Item Description Spare P ar t Number 17 Hard drives (include frame and connector) 5400-rpm, 100-GB 5400-rpm, 80-GB 5400-rpm, 60-GB 5400-rpm, 40-GB 412367-001 412366-001 412365-001 412364-001 18 Mini Card modules 802.
3–8 Maintenance and S ervice Gui de Illustr ated P arts Catalog Com pu te r Ma jor Components.
Illustr ated P arts Catalog Maintenance and Se rvice Guide 3–9 Ta b l e 3 - 1 Spare P ar ts: Computer Major Components (Continued) Item Description Spare P ar t Number 18 Mini Card modules (Continued) 802.11a/b/g WLAN module f or use in the countr ies listed below .
3–10 Maintenance and Serv ice Guide Illustr ated P arts Catalog Com pu te r Ma jor Components.
Illustr ated P arts Catalog Maintenance and S ervice Gui de 3–11 Ta b l e 3 - 1 Spare P ar ts: Computer Major Components (Continued) Item Description Spare P ar t Number 19 Memory modules , 1-DIMM, .
3–12 Maintenance and Serv ice Guide Illustr ated P arts Catalog 3 .3 Di splay Assem bly Compo nents Displa y Assembl y Componen ts.
Illustr ated P arts Catalog Maintenance and S ervice Gui de 3–13 T able 3-2 Display Assemb ly Components Spare P ar t Number Information Item Description Spare P ar t Number 1 Display bezel 412344-001 2 Display hinge co vers 412357-001 3 Display hinges 412356-001 4 Display panels 14.
3–14 Maintenance and Serv ice Guide Illustr ated P arts Catalog 3.4 M a s s S t ora ge D e vi ce s Mass S tor age Dev ice s.
Illustr ated P arts Catalog Maintenance and S ervice Gui de 3–15 T able 3-3 Mass Storage Devices Spare P ar t Number Information Item Description Spare P ar t Number 1 Hard drives (include frame and.
3–16 Maintenance and Serv ice Guide Illustr ated P arts Catalog 3.5 P l a stic s Kit Plastics K it Contents T able 3-4 Plastics Kit Spare P ar t Number Information Item Description Spare P ar t Numb.
Illustr ated P arts Catalog Maintenance and S ervice Gui de 3–17 3.6 Miscellan eous Ta b l e 3 - 5 Spare P ar ts: Miscellaneous (not illustrated) Description Spare P ar t Number Logo Kit 394370-001 .
3–18 Maintenance and Serv ice Guide Illustr ated P arts Catalog Pow e r c or d s Fo r u s e i n : A ustralia and New Zealand 394279-011 Belgium, Europe, Finland, F rance, Germany , Greece, the Nethe.
Illustr ated P arts Catalog Maintenance and S ervice Gui de 3–19 3.7 Sequen tial P art N umber Listin g T able 3-6 Spare P ar ts: Sequential P ar t Number Listing Spare P ar t Number Description 309.
3–20 Maintenance and Serv ice Guide Illustr ated P arts Catalog Spare P ar t Number Description 394279-AA1 P ow er cord for use in t he P eople’ s Republic of China 394279-AB1 P ow er cord for use.
Illustr ated P arts Catalog Maintenance and S ervice Gui de 3–21 Spare P ar t Number Description 407674-001 802.11a/b/g WL AN Mini Card module f or use in the MOW 1 countries listed below .
3–2 2 Maintenance and Serv ice Guide Illustr ated P arts Catalog Spare P ar t Number Description 407674-004 802.11b/g WLAN Mini Card module GL 412240-001 945GM system board 412331-001 ExpressCard assembly 412332-001 Intel Core Solo T1300 (1.66-GHz) processor (includes thermal pad) 412333-001 Intel Core Duo T2500 (2.
Illustr ated P arts Catalog Maintenance and Se rvice Guide 3–2 3 Spare P ar t Number Description 412358-001 1-DIMM, DDR2, PC 2-4200, 533-MHz, 256-MB memor y module 412359-001 1-DIMM, DDR2, PC 2-4200.
3–2 4 Maintenance and Serv ice Guide Illustr ated P arts Catalog Spare P ar t Number Description 412397-001 F an/heat sink asse mb ly (includes ther mal pad) 412398-001 USB/S-Video board 412400-001 .
Maintenance and Se rvice Guide 4–1 4 Remo v al and Repl a cemen t Preliminaries This chapter provides essential information for proper and safe remov a l and replacement service.
4–2 Maintenance and S ervice Gui de Remo val and Replacemen t Preliminar ies Pl a s t i c Par t s Using excessi ve force during disassembly and reassembly can damage plastic parts. Use care when handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.
Remo val and Replaceme nt Pre liminarie s Maintenance and Se rvice Guide 4–3 4. 3 Pr e v enting Da mage to Re mo v able Dri v es Remov a ble dri ves are fragile components that must be handled with care.
4–4 Maintenance and S ervice Gui de Remo val and Replacemen t Preliminar ies 4.4 Pre venting Elec trostati c Dam ag e Many electronic components are sensiti ve to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensiti vity .
Remo val and Replaceme nt Pre liminarie s Maintenance and Se rvice Guide 4–5 4.5 P ac k agin g and T ranspor ting Precautions Use the follo wing grounding precautions when packaging and transporting equipment: ■ T o av oid hand contact, transport products in static-safe containers, such as tubes, bags, or boxes.
4–6 Maintenance and S ervice Gui de Remo val and Replacemen t Preliminar ies 4.6 W orksta tion Precau tions Use the follo wing grounding precautions at workstations: ■ Cov er the workstation with approv ed static-shielding material (refer to T able 4-2, “Static-Shielding Materials” ).
Remo val and Replaceme nt Pre liminarie s Maintenance and Se rvice Guide 4–7 4.7 Groundin g Eq uipm ent an d Methods Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ■ When seated, wear a wrist strap connected to a grounded system.
4–8 Maintenance and S ervice Gui de Remo val and Replacemen t Preliminar ies T able 4-1 shows ho w humidity af fects the electrostatic voltage le vels generated by dif ferent activities. T able 4-2 lists the shielding protection provided by antistatic bags and floor mats.
Maintenance and Se rvice Guide 5–1 5 Remo v al and Repl a cemen t Procedur es This chapter provides remo val and replacement procedures. There are as many as 84 scre ws, in 8 different sizes, that must be remov ed, replaced, or loosened, when servicing the computer .
5–2 Maintenance and S ervice Gui de Remo val and Replacemen t Procedur es 5 . 1 Serial N umber Report the computer serial number to HP when requesting information or ordering spare parts.
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–3 5 .2 Disasse mbl y Sequence C hart Use the chart belo w to determine the section number to be referenced when removing computer components. Disassembl y Sequence Char t Section Description # of Screws Remo ved 5.
5–4 Maintenance and S ervice Gui de Remo val and Replacemen t Procedur es 5 .3 Preparing th e Co mpu ter for Disasse mbl y Before you begin an y remov al or installation procedures: 1.
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–5 4. Remov e the battery pack by follo wing these steps: a. T urn the computer upside down with the front panel to ward you. b . Slide and hold the battery release latch 1 to the left.
5–6 Maintenance and S ervice Gui de Remo val and Replacemen t Procedur es 5 .4 Hard Driv e 1. Prepare the computer for disassembly (refer to Section 5.
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–7 2. Loosen the two black Phillips PM2.0×5.0 scre ws 1 that secure the hard dri ve cov er to the computer . 3. Lift the left side of the cov er 2 and swing it to the right. 4. Remov e the hard driv e cov er .
5–8 Maintenance and S ervice Gui de Remo val and Replacemen t Procedur es 5. Use the mylar tab 1 to lift the hard dri ve 2 until it disconnects from the computer .
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–9 7. Remov e the four Phillips PM2.5×4.0 screws 1 that secure the hard dri ve frame to the hard dri ve. 8. Lift the frame 2 straight up to remov e if from the hard driv e. 9. Slide the hard dri ve connector 3 of f the hard dri ve.
5–10 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 5. 5 C o m p u t e r F e e t The computer feet are adhesi ve-backed rubber pads. The feet are included in the Rubber Feet Kit, spare part number 412579-001. Replac ing the Computer F eet 5.
Re mov al and Replacemen t Procedur es Maintenance and S ervice Gui de 5–11 1. Prepare the computer for disassembly (refer to Section 5.3 ). 2. Loosen the two black Phillips PM2.0×5.0 scre ws 1 that secure the memory module compartment cov er to the computer .
5–12 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 5. Spread the retaining tabs 1 on each side of the memory module socket to release the memory module. (The edge of the memory module opposite the memory module socket rises aw ay from the computer .
Re mov al and Replacemen t Procedur es Maintenance and S ervice Gui de 5–13 5 .7 Mini C ard Module Mini Card Module Spare P ar t Number Information 802.
5–14 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 1. Prepare the computer for disassembly ( Section 5.3 ). 802.11a/b/g WLAN module fo r us e in the RO W countries listed below . 407674-003 China Ecuador Haiti Honduras P akistan Pe r u Qatar South K orea Uruguay V enezuela 802.
Re mov al and Replacemen t Procedur es Maintenance and S ervice Gui de 5–15 2. Loosen the black Phillips PM2.0×5.0 scre w 1 that secures the Mini Card compartment cov er to the computer . 3. Lift the rear edge of the Mini Card compartment cov er 2 up, and then swing it forward.
5–16 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 5. Make note of which wireless antenna cable is attached to which antenna clip on the Mini Card module before disconnecting the cables, then disconnect the cables 1 from the module.
Re mov al and Replacemen t Procedur es Maintenance and S ervice Gui de 5–17 5 .8 Optical Driv e 1. Prepare the computer for disassembly ( Section 5.3 ).
5–18 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 2. Remov e the Phillips PM2.0×8.5 screw 1 that secures the optical dri ve to the computer . 3. Insert a thin tool, such as a paper clip, into the media tray release hole 2 . (The optical dri ve media tray releases from the optical dri ve.
Re mov al and Replacemen t Procedur es Maintenance and S ervice Gui de 5–19 6. Remov e the two Phillips PM2.0×2.0 scre ws 1 that secure the optical dri ve bracket to the optical dri ve. 7. Remov e the optical driv e bracket 2 . Re mov ing the Optical Dr i ve Br ack et Re verse the abov e procedure to reassemble and install the optical dri ve.
5–20 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 5. 9 Sw i t c h C ove r 1. Prepare the computer for disassembly ( Section 5.
Re mov al and Replacemen t Procedur es Maintenance and S ervice Gui de 5–21 2. Position the computer with the rear panel to ward you. 3. Remov e the two silv er Phillips PM2.
5–2 2 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 4. T urn the computer display side up with the front panel to ward you. 5.
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–2 3 5. 1 0 Keyb o a r d 1. Prepare the computer for disassembly ( Section 5.3 ). 2. Remov e the optical driv e ( Section 5.8 ). 3. Remov e the switch cov er ( Section 5.9 ). 4. Close the computer .
5–2 4 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 6. Remov e the four Phillips PM2.0×3.0 screws 1 that secure the ke yboard to the computer . 7. Swing the rear edge of the ke yboard 2 up and forward until it rests on the palm rest.
Re mov al and Replacemen t Procedur es Maintenance and Se r v ice Guide 5–2 5 8. Release the ZIF connector 1 to which the ke yboard cable is connected and disconnect the ke yboard cable 2 from the system board. Disconnec ting the K ey boar d Cable 9.
5–2 6 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 5 . 1 1 Displa y Assemb ly 1. Prepare the computer for disassembly ( Section 5.3 ). 2. Remov e the memory module compartment cove r ( Section 5.6 ). 3. Remov e the Mini Card compartment cov er and disconnect the wireless antenna cables from the Mini Card ( Section 5.
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–2 7 9. Disconnect the display cable 1 from the system board. 10. Remov e the tape 2 that secures the wireless antenna cables to the top cov er . 11. Remov e the cables from the clips 3 in the top cov er .
5–2 8 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es Ä CAUT ION: Support the display a ssembl y when r emov i ng the follo wing scr ews . F ailure to su ppor t the display a ssembly can r esult in damage to the display a ssembly and othe r computer components .
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–2 9 14. Remov e the six rubber screw co vers 1 and the six Phillips PM2.5×6.0 scre ws 2 that secure the display bezel to the display assembly . ✎ The rubber scre w covers are included in the Rubber Feet Kit, spare part number 412579-001.
5–30 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 15. Flex the insides edges of the left and right sides 1 and the top and bottom sides 2 of the display bezel until the bezel disengages from the display enclosure. 16. Remov e the display bezel 3 .
Re mov al and Replacemen t Procedur es Maintenance and S ervice Gui de 5–31 ✎ The display release hooks are av ailable in the Display Hinge Kit, spare part number 412356-001. 17. If it is necessary to replace the display release hooks, remov e the two Phillips PM2.
5–3 2 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 19. Remov e the Phillips PM2.0×3.0 screw 1 that secures the display in verter to the display enclosure. 20. Lift the in verter 2 out of the enclosure as far as the display cable and backlight cables will allo w .
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–3 3 23. If it is necessary to replace the display hinge cov ers, remov e the two Phillips PM2.5×6.0 scre ws 1 that secure each cov er to the display enclosure. 24. Remov e the display hinge cov ers 2 .
5–34 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 25. Remov e the two Phillips PM2.5×6.0 scre ws 1 that secure the display panel to the display enclosure.
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–3 5 27. If it is necessary to replace the display hinges, remov e the two Phillips PM2.0×3.0 scre ws 1 that secure each hinge to the display panel. 28. Remov e the display hinges 2 .
5–3 6 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es ✎ The wireless antenna transcei vers and cables are included with the display enclosure, spare part number 412351-001. 29. If it is necessary to replace the wireless transcei vers and cables, remov e the two Phillips PM2.
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–3 7 5. 1 2 B a s e E n c l o s u re 1. Prepare the computer for disassembly ( Section 5.3 ) and remov e the following components: ❏ Hard dri ve ( Section 5.4 ) ❏ Optical dri ve ( Section 5.
5–38 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 2. Remov e the fifteen Phillips PM2.0×8.5 scre ws that secure the base enclosure to the computer .
Re mov al and Replacemen t Procedur es Maintenance and Se r v ice Guide 5–3 9 3. Remov e the three silver Phillips PM2.0×5.0 scre ws that secure the base enclosure to the computer . 4. Lift the base enclosure straight up and remov e it. Re mov ing the Base Enc losur e Re verse the abov e procedure to install the base enclosure.
5–40 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 5 . 1 3 USB/S - Vid eo Bo ard 1. Prepare the computer for disassembly ( Section 5.3 ) and remov e the following components: ❏ Optical dri ve ( Section 5.8 ) ❏ Switch cov er ( Section 5.
Re mov al and Replacemen t Procedur es Maintenance and S ervice Gui de 5–41 2. Remov e the two silver Phillips PM2.0×5.0 scre ws 1 that secure the USB/S-V ideo board to the top cov er . 3. Lift up on the right side of the board 2 to disconnect it from the system board.
5–4 2 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 5 . 1 4 Bluetooth Module 1. Prepare the computer for disassembly ( Section 5.3 ) and remov e the following components: ❏ Optical dri ve ( Section 5.8 ) ❏ Switch cov er ( Section 5.
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–4 3 2. T urn the USB/S-V ideo board upside down with the USB port facing you. 3. Remov e the two PM1.5×3.5 scre ws 1 that secure the Bluetooth module to the USB/S-V ideo board.
5–44 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 5 . 1 5 Sp eak er Assem bly 1. Prepare the computer for disassembly ( Section 5.3 ) and remov e the following components: ❏ Optical dri ve ( Section 5.8 ) ❏ Switch cov er ( Section 5.
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–4 5 2. Disconnect the speaker cable 1 from the system board. 3. Lift the speaker 2 straight up to remov e it from the top cov er . Re mov ing the Speak er Assembly Re verse the abov e procedure to install the speaker assembly .
5–46 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 5. 1 6 R TC B a t t e r y 1. Prepare the computer for disassembly ( Section 5.3 ) and remov e the following components: ❏ Optical dri ve ( Section 5.8 ) ❏ Switch cov er ( Section 5.
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–4 7 2. Remov e the R TC battery from the socket on the system board. Re mov ing the R T C Battery Re verse the abov e procedure to install the R TC battery . Be sure that the R TC battery is installed with the “+” sign facing up.
5–48 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 5 . 1 7 Fan/Heat Sink Assemb ly 1. Prepare the computer for disassembly ( Section 5.3 ) and remov e the following components: ❏ Optical dri ve ( Section 5.8 ) ❏ Switch cov er ( Section 5.
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–4 9 3. Disconnect the fan cable 1 from the system board. 4. Loosen the four Phillips PM2.5×5.0 scre ws 2 that secure the fan/heat sink assembly to the top co ver . 5. Remov e the fan/heat sink assembly 3 .
5–50 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 5. 1 8 P r o c e s s o r 1. Prepare the computer for disassembly ( Section 5.3 ) and remov e the following components: ❏ Optical dri ve ( Section 5.8 ) ❏ Switch cov er ( Section 5.
Re mov al and Replacemen t Procedur es Maintenance and S ervice Gui de 5–51 2. T urn the processor locking screw 1 one-half turn counterclockwise until you feel a click. 3. Lift the processor 2 straight up and remov e it. ✎ The gold triangle 3 on the processor should be aligned in the front right corner when you install the processor.
5–5 2 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 5. 1 9 Sys t e m B o a rd ✎ When replacing the system board, ensure that the follo wing components are remov ed from the defectiv e system board and installed on the replacement system board: ■ Memory modules ( Section 5.
Re mov al and Replacemen t Procedur es Maintenance and Se r v ice Guide 5–5 3 1. Prepare the computer for disassembly ( Section 5.3 ) and remov e the following components: ❏ Hard dri ve ( Section 5.4 ) ❏ Optical dri ve ( Section 5.8 ) ❏ Switch cov er ( Section 5.
5–54 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 4. T urn the top cover upside do wn with the front to ward you. 5. Release the ZIF connector 1 to which the LED board cable is connected and disconnect the cable 2 from the system board.
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–5 5 7. Flex and hold the left side of the top co ver 1 . 8. Lift the left side of the system board 2 until the USB 3 and 1394 connectors 4 clear the top cov er .
5–5 6 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 9. Flex and hold the front edge of the top co ver 1 . 10. Lift the system board 2 until the audio connectors 3 clear the top cov er .
Re mov al and Replacemen t Procedur es Maintenance and Se rvice Guide 5–5 7 11. Slide the system board to the left at an angle and remov e it from the top cov er . Re mov ing the S y stem Boar d Re verse the abov e procedure to install the system board.
5–5 8 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 5 .20 LED Board 1. Prepare the computer for disassembly ( Section 5.3 ) and remov e the following components: ❏ Optical dri ve ( Section 5.8 ) ❏ Switch cov er ( Section 5.
Re mov al and Replacemen t Procedur es Maintenance and Se r v ice Guide 5–5 9 3. Release the ZIF connector 1 to which the LED board cable is connected and disconnect the cable 2 from the system board. 4. Remov e the two Phillips PM2.0×3.0 scre ws 3 that secure the LED board to the top cov er .
5–60 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 5 .2 1 ExpressCard As semb ly 1. Prepare the computer for disassembly ( Section 5.3 ) and remov e the following components: ❏ Optical dri ve ( Section 5.8 ) ❏ Switch cov er ( Section 5.
Re mov al and Replacemen t Procedur es Maintenance and S ervice Gui de 5–61 3. Remov e the two Phillips PM2.0×2.0 scre ws that secure the ExpressCard assembly to the system board.
5–6 2 Maintenance and Serv ice Guide Remo val and Replacemen t Procedur es 4. T urn the system board right side up with the ExpressCard eject button to ward you.
Maintenance and Se rvice Guide 6–1 6 Spec ifica tions This chapter provides physical and performance specif ications. Ta b l e 6 - 1 Computer Dimensions Height (varies from front to bac k) Width Depth 3.29 cm to 3.89 cm 23.06 cm 33.40 cm 1.30 in to 1.
6–2 Maintenance and S ervice Gui de Spe cificat ion s Shock Operating Nonoperating 125 g, 2 ms, half-sine 200 g, 2 ms, half-sine Random Vibration Operating Nonoperating 0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min s weep rate 1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.
Spe cificat ion s Maintenance and Se rvice Guide 6–3 Ta b l e 6 - 2 14.0-inch, WXGA, SV A Display Dimensions Height Width Diagonal 27.94 cm 20.83 cm 35.56 cm 11.0 in 8.2 in 14.0 in Number of colors Up to 16.8 million Contrast ratio 250:1 Brightness 180 nits typical Pixel resolution Pitch Fo r ma t Configuration 0.
6–4 Maintenance and S ervice Gui de Spe cificat ion s Ta b l e 6 - 3 Hard Drives 80-GB 60-GB 60-GB 40-GB Dimensions Height Width We i g h t 9.5 mm 70 mm 99 g 9.
Spe cificat ion s Maintenance and Se rvice Guide 6–5 Ta b l e 6 - 4 Primary 6-cell, Li-Ion Battery Pac k Dimensions Height Width Depth We i g h t 2.00 cm 9.40 cm 13.40 cm 0.34 kg 0.79 in 3.70 in 5.28 in 0.75 lb Energ y V oltage Amp-hour capacity W att-hour capacity 11.
6–6 Maintenance and S ervice Gui de Spe cificat ion s Ta b l e 6 - 5 D VD/CD-R W Combo Drive Applicable disc Read: D VD-R, D VD-RW , D VD-ROM (D VD-5, D VD-9, D VD-10, DV D - 1 8 ) , CD-ROM (Mode 1 .
Spe cificat ion s Maintenance and Se rvice Guide 6–7 Disc thickness 1.2 mm (0.047 in) T rack pitch 0.74 µm Access time CD media D VD media Random Full stroke < 110 ms < 210 ms < 130 ms < 225 ms A udio output level Line-out, 0.
6–8 Maintenance and S ervice Gui de Spe cificat ion s Ta b l e 6 - 6 DV D ± RW / R a n d CD-R W Double-La yer Combo Drive Applicable disc Read: D VD-R, D VD-RW , D VD-ROM (D VD-5, D VD-9, D VD-10, .
Spe cificat ion s Maintenance and Se rvice Guide 6–9 Disc thickness 1.2 mm (0.047 in) T rack pitch 0.74 µm Access time CD media D VD media Random Full stroke < 175 ms < 285 ms < 230 ms < 335 ms A udio output level A udio-out, 0.
6–10 Maintenance and Serv ice Guide Spe cificat ion s Ta b l e 6 - 7 System DMA Hard ware DMA System Function DMA0 Not applicable DMA1 Not applicable DMA2 Not applicable DMA3 Not applicable DMA4 Dir.
Spe cificat ion s Maintenance and S ervice Gui de 6–11 Ta b l e 6 - 8 System Interrupts Hard ware IRQ System Function IRQ0 System timer IRQ1 Quick Launch b uttons IRQ2 Cascaded IRQ3 USB2 Enhanced Ho.
6–12 Maintenance and Serv ice Guide Spe cificat ion s Hard ware IRQ System Function IRQ12 Synaptics PS/2 por t pointing device IRQ13 Numeric data processor IRQ14 Primar y IDE channel IRQ15 Secondar .
Spe cificat ion s Maintenance and S ervice Gui de 6–13 Ta b l e 6 - 9 System I/O Addresses I/O Address (he x) System Function (shipping configuration) 0x00000000-0x00000CF7 PCI b us 0x00000000-0x000.
6–14 Maintenance and Serv ice Guide Spe cificat ion s I/O Address (he x) System Function (shipping configuration) 0x000001F0-0x000001F7 Primary IDE Channel 0x00000220-0x0000022F System board resourc.
Spe cificat ion s Maintenance and S ervice Gui de 6–15 I/O Address (he x) System Function (shipping configuration) 0x00000C6F-0x00000C6F System board resources 0x00000CD4-0x00000CD5 System board res.
6–16 Maintenance and Serv ice Guide Spe cificat ion s T able 6-10 System Memory Map Memory Map Address (he x) System Function (shipping configuration) 0xD4100000-0xD41FFFFF PCI standard PCI-to-PCI b.
Spe cificat ion s Maintenance and S ervice Gui de 6–17 Memory Map Address (he x) System Function (shipping configuration) 0xD4208000-0xD42087FF T exas Instruments OHCI Compliant IEEE 1394 Host Controller 0xD4200000-0xD4203FFF T exas Inst r uments OHCI Compliant IEEE 1394 Host Controller 0xD4204000-0xD4205FFF Broadcom 802.
6–18 Maintenance and Serv ice Guide Spe cificat ion s Memory Map Address (he x) System Function (shipping configuration) 0xD4209400-0xD42094FF Realtek R TL8139/810x F amily F ast Ethernet NIC 0xD400.
Maintenance and Se rvice Guide A–1 A Conn ec tor P in A ssi gnm ents Ta b l e A - 1 Universal Serial Bus Pin Signal Pin Signal 1 +5 VDC 3 Data + 2 Data – 4 Ground.
A–2 Maintenance and S ervice Gui de Connec tor Pin As signments Ta b l e A - 2 RJ-45 (Network) Pin Signal Pin Signal 1 T ransmit + 5 Unused 2 T ransmit – 6 Receive – 3 Receive + 7 Unused 4 Unuse.
Connec tor P in Assignments Maintenance and Se rvice Guide A–3 Ta b l e A - 3 S-Video-Out Pin Signal Pin Signal 1 TV -Ground 5 TV -CD 2 TV -CVBS 6 TV -Ground 3 TV - Ground 7 TV -YD 4 TV - Ground.
A–4 Maintenance and S ervice Gui de Connec tor Pin As signments Ta b l e A - 4 External Monitor Pin Signal Pin Signal 1 Red analog 9 +5 VDC 2 Green analog 10 Ground 3 Blue analog 11 Monitor detect 4.
Connec tor P in Assignments Maintenance and Se rvice Guide A–5 Ta b l e A - 5 RJ-11 (Modem) Pin Signal Pin Signal 1 Unused 4 Unused 2T i p 5U n u s e d 3 Ring 6 Unused.
A–6 Maintenance and S ervice Gui de Connec tor Pin As signments Ta b l e A - 6 A udio-In (Microphone) Pin Signal Pin Signal 1 Audio signal in 3 Ground 2 Audio signal in Ta b l e A - 7 A udio-Out (He.
Maintenance and Se rvice Guide B–1 B P o w er C ord Set Requirem ents 3-Con duc tor P o w er Cord Set The wide range input feature of the computer permits it to operate from any line v oltage from 100 to 120 or 220 to 240 volts A C.
B–2 Maintenance and S ervice Gui de P ow er Cor d Set Requirements Gen eral Requirements The requirements listed belo w are applicable to all countries. ■ The length of the po wer cord set must be at least 1.5 m (5.0 ft) and a maximum of 2.0 m (6.
P ow er Cor d Set Requirements Maintenance and Se rvice Guide B–3 Countr y- Spec ifi c Requirements 3-Conductor P ower Cor d Set Requirements Country/Region Accredited Agency Applicab le Note Number.
B–4 Maintenance and S ervice Gui de P ow er Cor d Set Requirements Ko r e a E K 4 The Netherlands KEMA 1 Norwa y NEMK O 1 P eople’ s Republic of China CCC 5 Sweden SEMK O 1 Switzerland SEV 1 T aiwan BSMI 4 United Kingdom BSI 1 United States UL 2 Notes: 1.
Maintenance and Se rvice Guide C–1 C Scre w Li sting This appendix provides specif ication and reference information for the scre ws used in the computer . All screws listed in this appendix are av ailable in the Screw Kit, spare part number 412387-001, and the Display Scre w Kit, spare part number 417713-001.
C–2 Maintenance and Serv ice Guide Scr ew Listing Black Phillip s P M2 .0×5 .0 S cr e w Locati ons Ta b l e C - 1 Black Phillips PM2.0×5.0 Scre w Color Qty .
Scr ew Listing Maintenance and Se rvice Guide C–3 Black Phillip s P M2 .0×5 .0 S cr e w Locati ons Ta b l e C - 1 Black Phillips PM2.0×5.0 Scre w (Continued) Color Qty . Length Thread Head Width Black 11 5.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the Mini Card mo dule to the computer (documented in Section 5.
C–4 Maintenance and Serv ice Guide Scr ew Listing Black Phillip s P M2 .0×5 .0 S cr e w Locati ons Ta b l e C - 1 Black Phillips PM2.0×5.0 Scre w (Continued) Color Qty . Length Thread Head Width Black 11 5.0 mm 2.0 mm 4.0 mm Where used: 4 screws that secure the displa y assemb ly to the computer (documented in Section 5.
Scr ew Listing Maintenance and Se rvice Guide C–5 Phillips P M2 . 5×4.0 S cr ew L ocations Ta b l e C - 2 Phillips PM2.5×4.0 Screw Color Qty . Length Thread Head Width Silver 4 4.0 mm 2.5 mm 4.0 mm Where used: 4 screws that secure the hard driv e fram e to the hard drive (documented in Section 5.
C–6 Maintenance and Serv ice Guide Scr ew Listing Phillips P M2 . 0×8.5 Sc r ew L ocation Ta b l e C - 3 Phillips PM2.0×8.5 Screw Color Qty . Length Thread Head Width Black 16 8.5 mm 2.0 mm 4.0 mm Where used: One screw that secures the optical dr iv e to the computer (documented in Section 5.
Scr ew Listing Maintenance and Se rvice Guide C–7 Phillips P M2 . 0×8.5 Sc r ew L ocations Ta b l e C - 3 Phillips PM2.0×8.5 Screw (Continued) Color Qty . Length Thread Head Width Black 16 8.5 mm 2.0 mm 4.0 mm Where used: 15 screws that secure the base encl osure to the computer (documented in Section 5.
C–8 Maintenance and Serv ice Guide Scr ew Listing Silver Phillips P M2 .0×5 .0 Scr ew L ocations Ta b l e C - 4 Silver Phillips PM2.0×5.0 Screw Color Qty . Length Thread Head Width Silver 14 5.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the s witch co v er to the computer (documented in Section 5.
Scr ew Listing Maintenance and Se rvice Guide C–9 Silver Phillips P M2 .0×5 .0 Scr ew L ocations Ta b l e C - 4 Silver Phillips PM2.0×5.0 Screw (Continued) Color Qty . Length Thread Head Width Silver 14 5.0 mm 2.0 mm 4.0 mm Where used: 3 screws that secure the base enclosur e to the computer (documented in Section 5.
C–10 Maintenance and S ervice Gui de Scr ew Listing Silver Phillips P M2 .0×5 .0 Scr ew L ocations Ta b l e C - 4 Silver Phillips PM2.0×5.0 Screw (Continued) Color Qty . Length Thread Head Width Silver 14 5.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the USB/S-Video bo ard to the computer (documented in Section 5.
Scr ew Listing Maintenance and S ervice Gui de C–11 Silver Phillips P M2 .0×5 .0 Scr ew L ocations Ta b l e C - 4 Silver Phillips PM2.0×5.0 Screw (Continued) Color Qty . Length Thread Head Width Silver 14 5.0 mm 2.0 mm 4.0 mm Where used: 4 screws that secure the f an/heat sink assemb ly to the computer (documented in Section 5.
C–12 Maintenance and S ervice Gui de Scr ew Listing Silver Phillips P M2 .0×5 .0 Scr ew L ocations Ta b l e C - 4 Silver Phillips PM2.0×5.0 Screw (Continued) Color Qty . Length Thread Head Width Silver 14 5.0 mm 2.0 mm 4.0 mm Where used: 3 screws that secure the system boar d to the computer (documented in Section 5.
Scr ew Listing Maintenance and S ervice Gui de C–13 Phillips P M2 .0×3 .0 Sc re w Locations Ta b l e C - 5 Phillips PM2.0×3.0 Screw Color Qty . Length Thread Head Width Black 15 3.0 mm 2.0 mm 4.0 mm Where used: 4 screws that secure the k eyboard to the computer (documented in Section 5.
C–14 Maintenance and S ervice Gui de Scr ew Listing Phillips P M2 .0×3 .0 Sc re w Location Ta b l e C - 5 Phillips PM2.0×3.0 Screw (Continued) Color Qty . Length Thread Head Width Black 15 3.0 mm 2.0 mm 4.0 mm Where used: One screw that secures the displa y inv er ter to the display assemb ly (documented in Section 5.
Scr ew Listing Maintenance and S ervice Gui de C–15 Phillips P M2 .0×3 .0 Sc re w Locations Ta b l e C - 5 Phillips PM2.0×3.0 Screw (Continued) Color Qty . Length Thread Head Width Black 15 3.0 mm 2.0 mm 4.0 mm Where used: 4 screws that secure the displa y hinges to the displa y assembly (documented in Section 5.
C–16 Maintenance and S ervice Gui de Scr ew Listing Phillips P M2 .0×3 .0 Sc re w Locations Ta b l e C - 5 Phillips PM2.0×3.0 Screw (Continued) Color Qty . Length Thread Head Width Black 15 3.0 mm 2.0 mm 4.0 mm Where used: 4 screws that secure the wi reless antenna tr ansceivers to the displa y enclosure (documented in Section 5.
Scr ew Listing Maintenance and S ervice Gui de C–17 Phillips P M2 .0×3 .0 Sc re w Locations Ta b l e C - 5 Phillips PM2.0×3.0 Screw (Continued) Color Qty . Length Thread Head Width Black 15 3.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the LED board to the computer (documented in Section 5.
C–18 Maintenance and S ervice Gui de Scr ew Listing Phillips P M1.5×3 .5 Sc re w Locations Ta b l e C - 6 Phillips PM1.5×3.5 Screw Color Qty . Length Thread Head Width Silver 2 3.5 mm 1.5 mm 3.0 mm Where used: 2 screws that secure the Bluetoot h board to the USB/S-Video board (documented in Section 5.
Scr ew Listing Maintenance and S ervice Gui de C–19 Phillips P M2 .0×2 .0 Sc re w Locations Ta b l e C - 7 Phillips PM2.0×2.0 Screw Color Qty . Length Thread Head Width Silver 4 2.0 mm 2.0 mm 3.0 mm Where used: 2 screws that secure the optical driv e brac k et to the optical drive (documented in Section 5.
C–20 Maintenance and S ervice Gui de Scr ew Listing Phillips P M2 .0×2 .0 Sc re w Locations Ta b l e C - 7 Phillips PM2.0×2.0 Screw (Continued) Color Qty . Length Thread Head Width Silver 4 2.0 mm 2.0 mm 3.0 mm Where used: 2 screws that secure the ExpressC ard assemb ly to the system board (documented in Section 5.
Scr ew Listing Maintenance and S ervice Gui de C–21 Philli ps P M2 .5×6 .0 Scr ew L ocat ions Ta b l e C - 8 Phillips PM2.5×6.0 Screw Color Qty . Length Thread Head Width Silver 16 6.0 mm 2.5 mm 5.0 mm Where used: 6 screws that secure the displa y bezel to the displa y assembly (documented in Section 5.
C–2 2 Maintenance and S ervice Gui de Scr ew Listing Philli ps P M2 .5×6 .0 Scr ew L ocat ions Ta b l e C - 8 Phillips PM2.5×6.0 Screw (Continued) Color Qty . Length Thread Head Width Silver 16 6.0 mm 2.5 mm 5.0 mm Where used: 4 screws that secure the displa y rele ase hooks to the displa y enclosure (documented in Section 5.
Scr ew Listing Maintenance and Se rvice Guide C–2 3 Philli ps P M2 .5×6 .0 Scr ew L ocat ions Ta b l e C - 8 Phillips PM2.5×6.0 Screw (Continued) Color Qty . Length Thread Head Width Silver 16 6.0 mm 2.5 mm 5.0 mm Where used: 4 screws that secure the displa y hing e cov e rs to the displa y enclosure (documented in Section 5.
C–2 4 Main tenance and Servi ce Guide Scr ew Listing Philli ps P M2 .5×6 .0 Scr ew L ocat ions Ta b l e C - 8 Phillips PM2.5×6.0 Screw (Continued) Color Qty . Length Thread Head Width Silver 16 6.0 mm 2.5 mm 5.0 mm Where used: 2 screws that secure the displa y panel to the displa y enclosure (documented in Section 5.
Maintenance and Se rvice Guide D–1 D Disp l ay Compon ent Recy c ling Å W ARNIN G: The bac klight contains mer cury . Caution should be ex er c ised when r emov ing and handling the backligh t to av oid damaging this component and cau sing exposur e to the merc ury .
D–2 Maintenance and Serv ice Guide Display C omponent Recy cling This appendix provides disassembl y instructions for the display assembly . The display assembly must be disassembled to gain access to the backlight 1 and the LCD panel 2 . ✎ Disassembly procedures dif fer from one display assembly to another .
Display C omponent R ecyc ling Maintenance and Se rvice Guide D–3 Perform the follo wing steps to disassemble the display assembly: 1. Remov e all screw co vers 1 and scre ws 2 that secure the display bezel to the display assembly .
D–4 Maintenance and Serv ice Guide Display C omponent Recy cling 2. Lift up and out on the left and right inside edges 1 and the top and bottom inside edges 2 of the display bezel until the bezel disengages from the display assembly . 3. Remov e the display bezel 3 .
Display C omponent R ecyc ling Maintenance and Se rvice Guide D–5 4. Disconnect all LCD panel cables 1 from the display in verter board and remov e the in verter board 2 .
D–6 Maintenance and Serv ice Guide Display C omponent Recy cling 5. Remov e all screws 1 that secure the LCD panel to the display enclosure. 6. Remov e the LCD panel 2 from the display enclosure.
Display C omponent R ecyc ling Maintenance and Se rvice Guide D–7 7. T urn the LCD panel upside down. 8. Remov e all screws that secure the LCD panel frame to the LCD panel.
D–8 Maintenance and Serv ice Guide Display C omponent Recy cling 9. Use a sharp-edged tool to cut the tape 1 that secures the side of the LCD panel to the LCD panel frame.
Display C omponent R ecyc ling Maintenance and Se rvice Guide D–9 11. Remov e the screws 1 that secure the backlight co ver to the LCD panel. 12. Lift the top edge of the backlight cov er 2 and swing it forward.
D–10 Maintenance and S ervice Gui de Display C omponent Recy cling 14. T urn the LCD panel right-side up. 15. Remov e the backlight cables 1 from the clip 2 in the LCD panel.
Display C omponent R ecyc ling Maintenance and S ervice Gui de D–11 16. T urn the LCD panel upside down. 17. Remov e the backlight frame from the LCD panel.
D–12 Maintenance and S ervice Gui de Display C omponent Recy cling Å W ARNIN G: The bac klight contains mer cury . Caution should be ex er c ised when r emov ing and handling the backligh t to av oid damaging this component and cau sing exposur e to the merc ury .
Display C omponent R ecyc ling Maintenance and S ervice Gui de D–13 19. Disconnect the display cable 1 from the LCD panel. 20. Remov e the screws 2 that secure the LCD panel to the LCD rear panel. 21. Release the LCD panel 3 from the LCD rear panel.
D–14 Maintenance and S ervice Gui de Display C omponent Recy cling 23. Remov e the LCD panel. Re mov ing the L CD P anel 24. Recycle the backlight and LCD panel.
Maintenance and Se rvice Guide Index–1 Ind e x 1394 port 1–9 A AC adapter, spare part number 3–17 , 3–20 arrow keys 1–13 audio troubleshooting 2–23 audio-in (microphone) jack location 1–.
Index–2 Maintenance and Se r vi ce Guide Index Security Menu 2–4 Tools Menu 2–5 computer specifications 6–1 connector pin assignments external monitor A–4 headphone A–6 microphone A–6 mo.
Index Maintenance and Se rvice Guide Index–3 DVD±RW/R and CD-RW Double-Layer Combo Drive OS loading problems 2–22 precautions 4–3 spare part number 3–11 , 3–15 , 3–20 , 3–23 , 3–24 , .
Index–4 Maintenance and Se r vi ce Guide Index headphone jack location 1–7 pin assignments A–6 headset, spare part number 3–17 , 3–19 HP backpack, spare part number 3–17 , 3–20 HP Mobile.
Index Maintenance and Se rvice Guide Index–5 N network jack location 1–11 pin assignments A–2 network, troubleshooting 2–28 nonfunctioning device, troubleshooting 2–16 , 2–25 num lock key .
Index–6 Maintenance and Se r vi ce Guide Index security cable slot 1–11 serial number 3–1 , 5–2 service considerations 4–1 speaker assembly removal 5–44 spare part number 3–5 , 3–20 , .
Index Maintenance and Se rvice Guide Index–7 U Universal Serial Bus (USB) connector location 1–9 , 1–11 pin assignments A–1 unknown password 1–4 USB camera cable, spare part number 3–22 US.
Een belangrijk punt na aankoop van elk apparaat Compaq 408525-001 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Compaq 408525-001 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Compaq 408525-001 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Compaq 408525-001 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Compaq 408525-001 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Compaq 408525-001 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Compaq 408525-001 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Compaq 408525-001 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
