Gebruiksaanwijzing /service van het product C180 van de fabrikant Compaq
Ga naar pagina of 242
Model C160 / C180 / C200 / C240 / C360 Owner ’ s Guide HP Part No. A4200-90050 Edition E1298 Printed in U.S.A..
Copyright Hewlett-Packard Co. 1998 Printing History First Printing: December 1998 UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Limited. NOTICE The information contained in this document is subject to change without notice.
iii 5. The warranty period begins on the date of delivery or on the date of instal- lation if installed by HP . If customer schedules installation or causes instal- lation by HP to be delayed more than 30 days after delivery , warranty begins on the 31st day from delivery .
This document contains proprietary information that is protected by copy- right. All rights reserved. No part of this document may be photocopied, reproduced or translated to another language without the prior written con- sent of Hewlett-Packard Company .
Contents v Preface xiii Audience xiv Safety and Regulatory Statements xiv Release Document(s) xiv Related Manuals xv Revision History xv Documentation Conventions xvi Problems, Questions, and Suggesti.
vi Contents SCSI Connectors 19 TOC Button 19 Power Cord Connector 19 Monitors 20 Keyboard 21 Pointing Devices 21 Operating System Overview 22 2 Using Y our CD-ROM Drive CD-ROM Drive and CD-ROM Media D.
Contents vii 3 Using Y our Digital Data Storage (DDS) T ape Drive DDS T ape Drive and Data Cassette Descriptions 45 DDS Drive 45 Storage Capacities 45 Controls and Indicators 46 LEDs 47 LED W arning C.
viii Contents Using Device Files 64 Formatting a New Diskette 65 T ransferring Data T o and From a Floppy Diskette 66 Saving Files to a Floppy Diskette 66 Restoring Files from a Floppy Diskette to Y o.
Contents ix Special V ideo Configuration Statements 91 For EN55022 or CISPR 22 Applications: 91 For FCC Applications: 91 Emissions Regulations 92 Federal Communications Commission (FCC) 92 VCCI Class B ITE (Japan) 93 Korea RRL (EMI Class A) 93 Emissions Regulations Compliance 93 Acoustics 94 Regulation On Noise Declaration For Machines -3.
x Contents Installing a Hard Disk Drive in Position 1 1 13 Installing a Hard Disk Drive in Position 3 or Position 4 1 15 Replacing the Storage T ray 118 Configuring a Hard Disk Drive 120 Removing the.
Contents xi Ultra, W ide-SE SCSI Bus Configuration Constraints 160 Determining SCSI Bus Length 161 Narrow , Single-Ended SCSI Bus Length 161 Fast, W ide Differential SCSI Bus Length 163 Ultra, W ide,.
xii Contents Memory Information Sample 2 197 Displaying the Status of the System I/O 198 Setting the Auto Boot and Auto Search Flags 199 Displaying and Setting the Security Mode 201 Displaying and Set.
xiii Preface This owner ’ s guide describes how to use your HP 9000 C Class workstation. This manual assumes that you have installed your workstation as described in the C Class Har dwar e Installation Car d.
xiv Audience This guide is intended for HP 9000 Model C160/C180/C200/C240/C360 workstation users. Safety and Regulatory Statements See Appendix A in the back of this manual for safety and regulatory state- ments that apply to this workstation.
xv Related Manuals Refer to the following manuals for more information: • C Class Har dwar e Installation Car d (A4200-90012) • Using Your HP Workstation (A2615-90003) • Installing and Updating .
xvi Documentation Conventions Unless otherwise noted in the text, this guide uses the following symbolic conventions. user-supplied values Italic words or characters in for- mats and command descriptions represent values that you must supply . sample user input In examples, information that the user enters appears in color .
xvii Pr oblems, Questions, and Suggestions If you have any problems, questions, or suggestions with our hardware, soft- ware, or documentation, please call 1-800-633-3600 (US & Canada) or con- tact the HP Response Center for your country .
xviii.
1 1 Product Information.
2 Product Information This chapter introduces the HP 9000 Model C160/C180/C200/C240/C360 workstations, including their controls and indicators. This chapter discusses the following topics: • Product.
3 Product Information Product Description Product Description The Model C160/C180/C200/C240/C360 workstations contain the follow- ing key features: • Processor Performance 160 MHz (Model C160) 180 MHz (Model C180) 200 MHz (Model C200) 236 MHz (Model C240) 367 MHz (Model C360) • Operating System: Native HP-UX HP-UX 10.
4 Product Information Product Description • Internal Storage Devices Fast, Wide Differential SCSI Hard Disk Drives (C160/C180) or Ultra, Wide Single-Ended (C200 /C240/C360 ) 1-inch Low Profile Drive (up to two) 1.6-inch Full Height Drive (one) Single-Ended SCSI Removable Media CD-ROM Drive or 2.
5 Product Information System Unit Front Panel Controls System Unit Front Panel Controls Figure 1 shows the location of the system unit front panel controls. Figure 1 System Unit Front Panel Controls System Power Switch Use the power switch to power the system unit on and off.
6 Product Information System Unit Front Panel Controls Power LED The power LED is located on the left side of the front panel on the disk tray . It lights when the system unit power is on and flashes until the OS is booted. Once the OS is booted, the LED remains on without flashing, indicating that a soft shutdown is enabled.
7 Product Information System Unit Front Panel Controls Audio Controls Next to the system LEDs are the following audio controls: The volume control, headset jack, and microphone jack features of the CD- ROM are supported through applications only .
8 Product Information System Unit Front Panel Controls Storage Device Controls and Features The Model C160/C180/C200/C240/C360 workstations allow up to two of the following internal storage devices: CD-ROM drive, DDS tape drive, or floppy drive. The following sections describe the controls and features of these devices.
9 Product Information System Unit Front Panel Controls T able 1 CD-ROM Drive Controls and Featur es Control/Featur e Purpose Busy Indicator Lights during a data access oper- ation and blinks during a data transfer .
10 Product Information System Unit Front Panel Controls DDS T ape Drive Y our DDS tape drive is either a DDS-DC (early or later model) or a DDS-2 tape drive with a 3.
11 Product Information System Unit Front Panel Controls Figure 5 DDS-2 Drive Controls and Indicators T able 2 DDS T ape Drive Contr ols and Features Control/Featur e Purpose Eject Button Push the eject button to remove tape cassettes from the drive. Drive LEDs The DDS drive LEDs light and flash to indicate drive status and error con- ditions.
12 Product Information System Unit Front Panel Controls Floppy Disk Drive Figure 6 shows the operating controls and features of the floppy drive, and T able 3 describes them.
13 Product Information System Unit Rear Panel Connectors System Unit Rear Panel Connectors This section describes the following connectors on the system unit’ s rear panel: • Security loop • Audio connectors • Keyboard and mouse connectors • HP parallel (Centronics) I/O connector • 802.
14 Product Information System Unit Rear Panel Connectors Figure 7 System Unit Rear Panel Connectors Pullout Card The pullout card contains serial and model number information along with regulatory agency information.
15 Product Information System Unit Rear Panel Connectors Audio Connectors The Model C160/C180/C200/C240/C360 workstations have audio input and output capability through external input and output connectors on the rear panel and through an internal speaker .
16 Product Information System Unit Rear Panel Connectors Built-in mono speaker • Audio CODEC Crystal CS4215 T able 4 summarizes the audio electrical specifications for the Model C160/ C180/C200/C240/C360 workstations. T able 4 Audio Electrical Specifications Frequency Response 25-20,000Hz Input Sensitivity/Impedance Line Out 2.
17 Product Information System Unit Rear Panel Connectors PS/2 Keyboard and Mouse Connectors The PS/2 connectors provide an interface to the system for the keyboard, mouse, and a variety of other pointing devices, such as trackballs. Consult the documentation that accompanies each input device for specific informa- tion concerning its use.
18 Product Information System Unit Rear Panel Connectors Serial Input/Output Connectors There are a variety of pointing devices (mouse or trackball) or peripheral devices that can attach to the Serial Input/Output (SIO) ports on the worksta- tion. Peripheral devices include printers, plotters, modems, and scanners.
19 Product Information System Unit Rear Panel Connectors SCSI Connectors Use the SCSI connectors to connect external SCSI devices such as DDS-for- mat tape drives and CD-ROM drives. Consult the documentation that accompanies each SCSI device for specific information concerning its use.
20 Product Information Monitors Monitors The Model C160/C180 workstations have a graphics controller built-in on the I/O board. The Model C180/C200/C240/C360 workstations have a high- performance graphics card installed in an option slot.
21 Product Information Keyboard Keyboard The C160/C180/C200/C240/C360 systems use a PS/2 keyboard which con- nects to the PS/2 interface connector on the rear of your workstation. Pointing Devices The PS/2 connector , the HIL port, or the Serial ports support using an HP three-button mouse, a trackball, or other options as pointing devices.
22 Product Information Operating System Overview Operating System Overview The Model C160/C180 workstations use version 10.20 or later of the HP-UX operating system. The Model C200/C240 workstations require the W orkstation Additional Core Enhancements (ACE 9707) for HP-UX 10.
23 2 Using Your CD-ROM Drive.
24 Using Y our CD-ROM Drive This chapter describes how to use your CD-ROM drive. It is divided into the following sections: • CD-ROM drive and CD-ROM media descriptions • Operating the CD-ROM Driv.
25 Using Y our CD-ROM Drive CD-ROM Drive and CD-ROM Media Descriptions CD-ROM Drive and CD-ROM Media Descriptions This section describes basic information needed for using the CD-ROM drive and CD-ROM discs. CD-ROM Drive The CD-ROM drive is a random access read-only mass storage device that uses removable CD-ROM discs.
26 Using Y our CD-ROM Drive CD-ROM Drive and CD-ROM Media Descriptions Controls and Features Figure 8 shows and T able 6 describes the operating controls and features of the CD-ROM drives.
27 Using Y our CD-ROM Drive CD-ROM Drive and CD-ROM Media Descriptions NOTICE The V olume Control, Headset Jack, and Audio Jack features of the CD- ROM drive are supported through applications only . T able 6 CD-ROM Drive Operating Controls and Featur es Control/Featur e Purpose Headset Jack Y ou can plug mini-headphones with a 3.
28 Using Y our CD-ROM Drive CD-ROM Drive and CD-ROM Media Descriptions CD-ROM Media CD-ROM discs are 120 mm (4.7 in.) in diameter , and use one data surface with a capacity of approximately 600 megabytes. The data surface contains pits and flat spots arranged in a continuous spiral track, which is read at a constant speed.
29 Using Y our CD-ROM Drive Operating the CD-ROM Drive Operating the CD-ROM Drive This section describes how to perform tasks with your CD-ROM drive. Loading and Unloading a CD-ROM in the Disc Tray This subsection describes how to load or unload a CD-ROM disc in the CD- ROM drive.
30 Using Y our CD-ROM Drive Operating the CD-ROM Drive Loading a CD-ROM Disc in a Horizontally Mounted Drive This CD-ROM drive has an automatic loading/ejecting feature. T o load a disc in the CD-ROM drive, follow these steps: Figure 10 Placing a CD-ROM Disc in a Horizontally Mounted Drive 1 Check that the workstation is powered on.
31 Using Y our CD-ROM Drive Operating the CD-ROM Drive Unloading a CD-ROM Disc in a Horizontally Mounted Drive Perform the following steps to unload a disc from the CD-ROM drive: Figure 11 Removing a CD-ROM Disc From a Horizontally Mounted Drive 1 Press the eject button to eject the disc tray from the drive.
32 Using Y our CD-ROM Drive Operating the CD-ROM Drive Loading a CD-ROM Disc in a Vertically Mounted Drive T o load a disc in the CD-ROM drive, follow these steps: Figure 12 Releasing the Disc Holder Retainers 1 Make sure the four disc holders are disengaged from the disc holder retainers, as shown in Figure 12.
33 Using Y our CD-ROM Drive Operating the CD-ROM Drive 2 Hold the disc with the label side away from the tray and place the edge of the disc onto disc holders A and B as shown in Figure 13.
34 Using Y our CD-ROM Drive Operating the CD-ROM Drive Unloading a CD-ROM Disc in a Vertically Mounted Drive Perform the following steps to unload a disc from the CD-ROM drive: Figure 14 Removing a CD-ROM Disc From a Vertically Mounted Drive 1 Press the eject button to eject the disc tray from the drive.
35 Using Y our CD-ROM Drive Operating the CD-ROM Drive Verifying the CD-ROM Drive Operation T o verify that your workstation can communicate with the CD-ROM drive, follow these steps: 1 In a terminal .
36 Using Y our CD-ROM Drive Mounting and Unmounting a CD-ROM Disc Mounting and Unmounting a CD-ROM Disc T o access information on a CD-ROM disc, you must first mount the disc. This applies to file system information only . If you wish to load a music CD, for example, you would not need to mount the disc.
37 Using Y our CD-ROM Drive Mounting and Unmounting a CD-ROM Disc 4 The System Administration Manager window opens. Double-click on Peripheral Devices ->. 5 The Peripheral Devices window opens. Double-click on Disks and File Systems ->. 6 The Disks and File Systems window opens.
38 Using Y our CD-ROM Drive Mounting and Unmounting a CD-ROM Disc Unmounting a CD-ROM Disc Using SAM Use the following procedure to unmount a CD-ROM disc: NOTICE: Before you unmount a CD-ROM disc, mak.
39 Using Y our CD-ROM Drive Mounting and Unmounting a CD-ROM Disc 7 A window with the following message opens: Do you want to remove the disk? Click on Y es . 8 Press the eject button on the CD-ROM drive and remove the CD-ROM disc from the disc tray .
40 Using Y our CD-ROM Drive Mounting and Unmounting a CD-ROM Disc The busy light stays on after the self test when one of the following condi- tions exist: • A defective disc • A disc insertion er.
41 Using Y our CD-ROM Drive T roubleshooting Troubleshooting If you have trouble with any of these procedures for using your CD-ROM drive, see Chapter 5 of this book, “Solving Problems.
42 Using Y our CD-ROM Drive T roubleshooting.
43 3 Using Your Digital Data Storage (DDS) Tape Drive.
44 Using Y our Digital Data Storage (DDS) T ape Drive This chapter describes how to use the optional Digital Data Storage (DDS) tape drive. It also describes how to maintain and care for the drive.
45 Using Y our Digital Data Storage (DDS) T ape Drive DDS T ape Drive and Data Cassette Descriptions DDS Tape Drive and Data Cassette Descriptions This section describes basic information needed for using your DDS tape drive and data cassettes. DDS Drive Y our DDS tape drive is either a DDS-DC (early or later model) or a DDS-2 tape drive with a 3.
46 Using Y our Digital Data Storage (DDS) T ape Drive DDS T ape Drive and Data Cassette Descriptions Controls and Indicators Figure 15, Figure 16, and Figure 17 show the LEDs, and eject button of the DDS-format tape drives.
47 Using Y our Digital Data Storage (DDS) T ape Drive DDS T ape Drive and Data Cassette Descriptions LEDs This section describes the LED codes that are displayed. The two LEDs on the front panels of the DDS drives indicate different activ- ities or problems that occur .
48 Using Y our Digital Data Storage (DDS) T ape Drive DDS T ape Drive and Data Cassette Descriptions Figure 19 DDS-DC (Later Model) and DDS-2 Tape Drive LED Display Codes LED Warning Conditions The following sections describe actions to take if the LEDs indicate a warn- ing condition.
49 Using Y our Digital Data Storage (DDS) T ape Drive DDS T ape Drive and Data Cassette Descriptions If the LED indicators on your DDS-format drive display the Media W ear (Caution) condition, follow this procedure: 1 Check the system console for any tape error messages.
50 Using Y our Digital Data Storage (DDS) T ape Drive DDS T ape Drive and Data Cassette Descriptions Cleaning the Tape Heads Clean the heads of your tape drive after every 25 hours of tape drive use or if the Media W ear (Caution) signal is displayed on the LED.
51 Using Y our Digital Data Storage (DDS) T ape Drive DDS T ape Drive and Data Cassette Descriptions Setting the Write-Protect Tab on a Data Cassette Y ou can only store or change information on a data cassette when the write- protect tab is in the write position.
52 Using Y our Digital Data Storage (DDS) T ape Drive Operating the DDS T ape Drive Operating the DDS Tape Drive This section describes how to perform tasks with your DDS tape drive.
53 Using Y our Digital Data Storage (DDS) T ape Drive Operating the DDS T ape Drive Verifying the DDS Tape Drive Operation T o verify that your workstation can communicate with the DDS-format tape dri.
54 Using Y our Digital Data Storage (DDS) T ape Drive Operating the DDS T ape Drive Using Device Files Device files are special files that tell your system which system hardware pathway to use when communicating with a specific device, and what kind of device it is.
55 Using Y our Digital Data Storage (DDS) T ape Drive Operating the DDS T ape Drive Archiving Data This section describes how to transfer data to and from a DDS-format data cassette (saving and restoring) using the HP-UX tar command and your tape drive’ s device file.
56 Using Y our Digital Data Storage (DDS) T ape Drive Operating the DDS T ape Drive Restoring Files from a Data Cassette to Your System Use the following instructions to restore files from a data cassette to your system: 1 Load the data cassette into the tape drive.
57 Using Y our Digital Data Storage (DDS) T ape Drive Operating the DDS T ape Drive Further Command Information For additional information on using tar and a complete list of the command arguments, refer to the tar man page by typing the following: man tar The man utility looks up man pages on the system.
58 Using Y our Digital Data Storage (DDS) T ape Drive T roubleshooting Troubleshooting If you have trouble with any of these procedures for using your DDS tape drive, see Chapter 5 of this book, “Solving Problems.
59 4 Using Your 3.5-Inch Floppy Disk Drive.
60 Using Y our 3.5-Inch Floppy Disk Drive This chapter describes how to perform tasks that allow you to archive to or transfer data from the optional 3.
61 Using Y our 3.5-Inch Floppy Disk Drive Using the Floppy Diskette Using the Floppy Diskette This section describes basic information needed for using your floppy dis- kettes. Setting the Write-Protect Tab on a Diskette Y ou can only store or change information on a diskette when the write-pro- tect tab is in the write position.
62 Using Y our 3.5-Inch Floppy Disk Drive Using the Floppy Diskette Inserting and Removing a Diskette Follow these steps to insert and remove a diskette from the floppy disk drive: 1 Insert the diskette into the drive, as shown in Figure 23.
63 Using Y our 3.5-Inch Floppy Disk Drive Operating the Floppy Drive Operating the Floppy Drive This section describes how to perform tasks with your 3.
64 Using Y our 3.5-Inch Floppy Disk Drive Operating the Floppy Drive Using Device Files Device files are special files that tell your system which system hardware pathway to use when communicating with a specific device and what kind of device it is.
65 Using Y our 3.5-Inch Floppy Disk Drive Operating the Floppy Drive Formatting a New Diskette Y ou must always format a new floppy diskette with the mediainit utility before using it. T o format a new floppy diskette follow these steps: 1 Log in as root .
66 Using Y our 3.5-Inch Floppy Disk Drive Operating the Floppy Drive Transferring Data To and From a Floppy Diskette This section describes how to transfer data to and from your floppy diskette (saving and restoring) using the HP-UX tar command with your floppy drive’ s device file.
67 Using Y our 3.5-Inch Floppy Disk Drive Operating the Floppy Drive 3 Enter the following command line: tar -xvf devicefile pathname where devicefile is the device file as listed by sam and pathname is the path- name of the file or directory containing files that you want to restore from the diskette.
68 Using Y our 3.5-Inch Floppy Disk Drive Operating the Floppy Drive For More Information For more information on using tar and a complete list of the command argu- ments, refer to the tar man page by typing the following in a terminal win- dow: man tar The man utility looks up man pages on the system.
69 Using Y our 3.5-Inch Floppy Disk Drive Operating the Floppy Drive Configuring the Floppy Driver If you reload software or rebuild the Instant Ignition system on your work- station, you need to reconfigure the HP-UX Kernel to add the floppy driver .
70 Using Y our 3.5-Inch Floppy Disk Drive T roubleshooting Troubleshooting If you have trouble with any of these procedures for using your floppy disk drive, see Chapter 5 of this book, “Solving Problems.” Ordering Information T o order Hewlett-Packard micro flexible diskettes for use in your 3.
71 5 Solving Problems.
72 Solving Problems This chapter contains information to help you determine what’ s wrong with your system when you have problems. If you have a problem that isn’t listed in this chapter , or if your problem persists, contact your designated service representative.
73 Solving Problems Common Problems and Solutions Common Problems and Solutions The tables in this section list common problems you may encounter with your workstation.
74 Solving Problems Common Problems and Solutions Problems Loading and Booting the Operating System T able 10 describes possible problems you may encounter when loading and booting the operating system and offers solutions.
75 Solving Problems Common Problems and Solutions Problems with the 802.3 Network T able 1 1 describes possible problems you may encounter with the 802.3 net- work and offers solutions. T able 1 1 Problems with the 802.3 Network Problem Solution Cannot reach other sys- tems on the network.
76 Solving Problems Common Problems and Solutions Problems Using a Hard Disk Drive T able 12 describes possible problems you may encounter using the hard disk drive and offers solutions. T able 12 Problems Using a Hard Disk Drive Problem Solution The disk drive is not accessible or does not respond.
77 Solving Problems Common Problems and Solutions Problems Using the CD-ROM Drive T able 13 describes a possible problem you may encounter when you use the CD-ROM drive and offers a solution. T able 13 Problems Using the CD-ROM Drive Problem Solution The CD-ROM drive does not respond to com- mands.
78 Solving Problems Common Problems and Solutions Problems Using the DDS Tape Drive T able 14 describes a possible problem you may encounter using the DDS tape drive and offers solutions. T able 14 Problems Using the DDS T ape Drive Problem Solution The DDS tape drive does not respond to com- mands.
79 Solving Problems Common Problems and Solutions Problems Using the Floppy Disk Drive T able 15 describes a possible problem you may encounter using the floppy disk drive and offers a solution. T able 15 Problems Using the Floppy Disk Drive Problem Solution The floppy drive does not respond to commands.
80 Solving Problems LED Error Codes LED Error Codes This section contains information about the error codes displayed by the LEDs on the system’ s front panel. If an error occurs during the power-up diagnostics tests, the diagnostics use the front panel LEDs to display a code for the failing component.
81 Solving Problems LED Error Codes T able 16 LED Error Codes LED V alue RS-232 Chassis Code Range Description N/A Reserved 7500 No memory found F AUL T Likely cause: SIMMs or pr ocessor boar d N/A Re.
82 Solving Problems LED Error Codes FL T A088 - A0FF No console/IPL error F AUL T N/A Reserved N/A Reserved N/A Reserved N/A Power on value. Indicates processor board fault when this value remains for more than a second following power up.
83 Solving Problems Dealing with a Boot Failure Dealing with a Boot Failure If your usual boot device (typically a disk) is not responding as it should, you must try to boot from the disk (or another boot device) by selecting it manually .
84 Solving Problems Running System V erification T ests Running System Verification Tests HP-UX uses an online diagnostics product called the Support T ools Man- ager that allows system operation verfications.
85 Solving Problems Running System V erification T ests T o access the Support T ools Manager , perform the following steps: 1 At a command line prompt, enter the following: cstm The following message appears: Support Tool Manager Version A.01.00 Type ‘help’ for a list of available commands.
86 Solving Problems Running System V erification T ests.
87 A Safety and Regulatory Statements.
88 Safety and Regulatory Statements This appendix contains safety and regulatory statements pertaining to your C Class workstation. It provides information on the following topics: • Declaration of .
89 Safety and Regulatory Statements Declaration of Conformity 1 Declaration of Conformity 1.
90 Safety and Regulatory Statements Declaration of Conformity 2 Declaration of Conformity 2.
91 Safety and Regulatory Statements Special Video Configuration Statements Special Video Configuration Statements The following statements apply only to those applications which include a cable connected to the S-V ideo connector on the A4248A card.
92 Safety and Regulatory Statements Emissions Regulations Emissions Regulations Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and the Cana- dian Department of Communications.
93 Safety and Regulatory Statements Emissions Regulations Compliance VCCI Class B ITE (Japan) Korea RRL (EMI Class A) Emissions Regulations Compliance Any third-party I/O device installed in HP system(s) must be in accordance with the requirements set forth in the preceding Emissions Regulations state- ments.
94 Safety and Regulatory Statements Acoustics Acoustics Regulation On Noise Declaration For Machines -3. GSGV Lpa <70dB Lpa<70dB operator position am Arbeitsplatz normal operation normaler Betrieb per ISO 7779 nach DIN 45635 T .
95 Safety and Regulatory Statements Safety Statement Safety Statement This equipment conforms to the following safety standards: • UL 1950 • CSA 950 • IEC 950 • EN 60950.
96 Safety and Regulatory Statements Laser Safety Statement (U.S.A. Only) Laser Safety Statement (U.S.A. Only) The CD ROM mass-storage system is certified as a Class-1 laser product under the U.S. Department of Health and Human Services (DHHS) Radia- tion Performance Standard according to the Radiation Control for Health and Safety Act of 1968.
97 Safety and Regulatory Statements W arnings and Cautions Warnings and Cautions.
98 Safety and Regulatory Statements W arnings and Cautions.
99 B Changing Your Workstation’s Hardware Configuration.
100 Changing Y our Workstation’ s Hardware Configuration This appendix describes the procedures to change your workstation’ s hard- ware configuration.
101 Changing Y our Workstation’ s Hardware Configuration Checking the SCSI IDs Checking the SCSI IDs T o determine which SCSI IDs are currently in use on your system, use the ioscan command in a te.
102 Changing Y our Workstation’ s Hardware Configuration Checking the SCSI IDs 2 You can find out the SCSI IDs currently in use by looking under the H/W Path heading. The listing 8/16/5 scsi is the built-in SCSI bus controller. For devices connected to the built-in SCSI bus, such as disks, the fourth number is the SCSI ID for that device.
103 Changing Y our Workstation’ s Hardware Configuration Preparing Y our Workstation Preparing Your Workstation This section describes how to prepare your workstation for changing its con- figuration. Use the following procedure to prepare your workstation: 1 Power off your workstation by pressing the power button on the front panel.
104 Changing Y our Workstation’ s Hardware Configuration Preparing Y our Workstation Figure 25 Removing the Floor Stand 6 Lay the system unit on a flat surface, such as a table top. 7 Attach a static-grounding wrist strap to bare metal on the back of the system unit.
105 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices Installing Storage Devices This section describes how to install storage devices in your workstation.
106 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices Preparing to Install Your Storage Device This section describes information that you need to consider and procedures that you need to perform before installing any storage device.
107 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices Figure 26 Storage Tray Positions T able 18 Storage T ray Configurations Storage T ray Position Supported Devices Conditions 1 Floppy Drive 1-inch Low Profile Disk Drive 2 CD-ROM DDS-T ape 3 1-inch Low Profile Disk Drive 1.
108 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices Storage Device Cable Routing When you install your storage device, be aware of the suggested cable rout- ing paths as indicated in the cable routing label that is affixed to the top of the storage tray .
109 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices CAUTION: Be sure to support the storage tray from underneath while sliding it out of the system unit.
11 0 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices 2 From the rear of the storage tray, line up the disk slides on the CD-ROM or DDS tape drive with the position 1slots in the storage tray chassis, and slide it into place, as shown in Figure 29.
111 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices Installing a Floppy Drive Perform the following procedure to install a floppy drive in the storage tray: 1 Remov.
11 2 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices 4 From the front of the storage tray, line up the disk slides on the floppy drive with the position 2 slots in the storage tray chassis and slide it into place, as shown in Figure 31.
11 3 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices Installing a Hard Disk Drive in Position 1 Perform the following procedure to install a hard disk drive: 1 Remov.
11 4 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices Figure 33 Installing a Hard Disk Drive in Position 1 5 Push the drive in until the locking tabs snap into place. 6 Snap the disk filler panel into the lower bezel position.
11 5 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices Installing a Hard Disk Drive in Position 3 or Position 4 Perform the following procedure to install a hard disk drive in positions 3 or 4 of the storage tray: 1 Remove the two retaining screws from the disk interconnect board, as shown in Figure 34.
11 6 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices 5 From the rear of the storage tray, line up the disk slides on the hard disk drive with the position 3 or position 4 slots in the storage tray chassis and slide it into place, as shown in Figure 35.
11 7 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices 8 Slide the disk interconnect board into the storage tray, as shown in Figure 36. Figure 36 Installing the Disk Interconnect Board 9 Reconnect the user interface cable, fan cable, and the disk drive data and power cables to the disk interconnect board.
11 8 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices Replacing the Storage Tray 1 Slide the storage tray assembly into the system unit chassis, as shown in Figure 37. Figure 37 Installing the Storage Tray Assembly 2 Tighten the storage tray retaining screw, as shown in Figure 37.
11 9 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices If you installed a new hard disk drive, proceed to the section entitled “Con- figuring a Hard Disk Drive.
120 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices Configuring a Hard Disk Drive This section describes how to add a hard disk drive to your system as a file system using SAM. If you installed a new hard disk drive, follow these instructions to make your new disk usable as a file system.
121 Changing Y our Workstation’ s Hardware Configuration Installing Storage Devices 9 The Set Disk Usage and Options window opens. Select File System and click on OK . 10 The following screen messages appear: Task started. Creating the device file.
122 Changing Y our Workstation’ s Hardware Configuration Removing the Main T ray Assembly Removing the Main Tray Assembly Perform the following steps to remove the main tray assembly: 1 Power off the system, the monitor, and any peripheral devices.
123 Changing Y our Workstation’ s Hardware Configuration Removing the Main T ray Assembly 5 Place one hand on the top of the system unit and push, while pulling the handle on the rear panel with your other hand. See Figure 38. 6 Slide the main tray assembly out of the chassis.
124 Changing Y our Workstation’ s Hardware Configuration Replacing the Main T ray Assembly Replacing the Main Tray Assembly Perform the following steps to replace the main tray assembly: 1 Align the main tray assembly with the chassis and slide it into place, as shown in Figure 39.
125 Changing Y our Workstation’ s Hardware Configuration Replacing the Main T ray Assembly 5 Reconnect the power cables and any other cables that you disconnected when opening the workstation. 6 Power on the monitor , any peripheral devices, and the system unit.
126 Changing Y our Workstation’ s Hardware Configuration Installing Additional Memory Installing Additional Memory T ake a moment to read over the following important notes about installing memory .
127 Changing Y our Workstation’ s Hardware Configuration Installing Additional Memory Perform the following steps to add memory modules to your workstation. 1 Remove the main tray assembly according to the directions in “Removing the Main Tray Assembly” earlier in this appendix.
128 Changing Y our Workstation’ s Hardware Configuration Installing Additional Memory 3 Close the ejector tabs on each side of the memory connector to lessen the force needed to seat the memory module. See Figure 41. Figure 41 Installing Memory Modules 4 Place the memory module in the connector, lining it up with the guides.
129 Changing Y our Workstation’ s Hardware Configuration Installing Additional Memory 6 Replace the main tray assembly as described in “Replacing the Main Tray As- sembly,” earlier in this appendix.
130 Changing Y our Workstation’ s Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) Before installing the EGRAM module, perform the procedure in Removing the Main T ray Assembly on page 122.
131 Changing Y our Workstation’ s Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) 2 Slide the EISA slider to the side to remove it, as shown in Figure 43. 3 Remove the screw from the EISA retainer and remove it, as shown in Figure 43.
132 Changing Y our Workstation’ s Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) 5 Install the standoffs into the EGRAM module, as shown in Figure 44. Push the standoffs into the holes on the module until the clips fully emgage with the board.
133 Changing Y our Workstation’ s Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) 8 Make sure that the EISA fan is fully rotated, as shown in Figure 45. Figure 45 Rotating the EISA Fan 9 Slide the option boards into the slots that they came out of, as shown in Figure 46.
134 Changing Y our Workstation’ s Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) 10 Press in firmly on both ends of the option board at the same time to make sure that it is firmly seated in the backplane connector.
135 Changing Y our Workstation’ s Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) 13 Rotate the fan back into place, as shown in Figure 48.
136 Changing Y our Workstation’ s Hardware Configuration Installing an EISA, PCI, or GSC Option Board Installing an EISA, PCI, or GSC Option Board Y our workstation has 4 option slots, as shown in Figure 49. On C160/C180 workstations, slots 1 and 2 each support either GSC or EISA boards.
137 Changing Y our Workstation’ s Hardware Configuration Installing an EISA, PCI, or GSC Option Board Graphics Adapter Considerations If you are installing a graphics option, read the information in this section first.
138 Changing Y our Workstation’ s Hardware Configuration Installing an EISA, PCI, or GSC Option Board Graphics Paths graphics(0) is the built-in 8-plane graphics adapter (C160/C180 only). graphics(1) through graphics(4) are graphics adapters installed in option slots 1 through 4.
139 Changing Y our Workstation’ s Hardware Configuration Installing an EISA, PCI, or GSC Option Board Graphics Configuration Restrictions This subsection describes restrictions on the installation and support of graphics adapters. Graphics Displays The system supports only four graphics displays at a time.
140 Changing Y our Workstation’ s Hardware Configuration Installing an EISA, PCI, or GSC Option Board Upgrading a C160/180 With an HP VISUALIZE-FX Graphics Adapter When you upgrade a Model C160/180 to use the HP VISUALIZE-FX Graphics Adaptor you also need to upgrade the Model C160/180 power sup- ply .
141 Changing Y our Workstation’ s Hardware Configuration Installing an EISA, PCI, or GSC Option Board Installing the Option Board Follow these steps to install a GSC, EISA, or PCI board into your worksta- tion: 1 Remove the main tray assembly as described in “Removing the Main Tray As- sembly” earlier in this appendix.
142 Changing Y our Workstation’ s Hardware Configuration Installing an EISA, PCI, or GSC Option Board 4 Remove the EISA slider, as shown in Figure 52. 5 In the desired EISA slot, turn the blank plate’s locking knob counter-clockwise to unlock the plate, as shown in Figure 52.
143 Changing Y our Workstation’ s Hardware Configuration Installing an EISA, PCI, or GSC Option Board 7 Slide the board into the slot, as shown in Figure 53.
144 Changing Y our Workstation’ s Hardware Configuration Installing an EISA, PCI, or GSC Option Board 9 Replace the EISA retainer and its screw, as shown in Figure 54. Figure 54 Installing the EISA Retainer and EISA Slider 10 Replace the EISA slider, as shown in Figure 54.
145 Changing Y our Workstation’ s Hardware Configuration Installing an EISA, PCI, or GSC Option Board 11 Rotate the fan back into place, as shown in Figure 55.
146 Changing Y our Workstation’ s Hardware Configuration Replacing the Battery Replacing the Battery 1 Remove the main tray as described in “Removing the Main Tray Assembly” earlier in this chapter. 2 Note the orientation of the battery. Make sure that you put the new battery in place with the positive (+) side facing in the same direction.
147 Changing Y our Workstation’ s Hardware Configuration Replacing the Battery 4 Insert the new battery in the same orientation as the old one. (Use only HP part number 1420-0314 or equivalent.) NOTICE: If you cannot gain access to the battery , you may need to remove an option board.
148 Changing Y our Workstation’ s Hardware Configuration Changing Y our Monitor T ype Changing Your Monitor Type Y our system ships from the factory preset to use a monitor with a specific resolution and frequency . If you replace your monitor with a different type, you must reconfigure your workstation to support it.
149 Changing Y our Workstation’ s Hardware Configuration Changing Y our Monitor T ype Changing the Console to External Terminal In the event that your console stops displaying to your graphics device, use the fol- lowing procedure to display to console to an external terminal: 1 Turn system power off.
150 Changing Y our Workstation’ s Hardware Configuration Changing Y our Monitor T ype.
151 C SCSI Connections.
152 SCSI Connections This appendix provides information about connecting Small Computer Sys- tem Interface (SCSI) devices to an HP 9000 C160/C180/C200/C240/C360 workstation.
153 SCSI Connections SCSI Bus Differences SCSI Bus Differences A Small Computer Systems Interface (SCSI) bus is an IEEE standard bus for connecting your workstation to internal and external devices (SCSI devices) running at different speeds, singly or in combination.
154 SCSI Connections SCSI Bus Differences Ultra Wide-SE (C200/C240/ C360 only) 16 bits 16 3 meters (9.84 feet) Internal and external Embedded Up to 40 Mbytes per second * Address 7 is reserved for host controller use on all buses.
155 SCSI Connections SCSI Bus Differences T able 20 SCSI Bus Addresses, ID Numbers, and Arbitration Priorities SCSI Address SCSI ID Number Priority 15 . . . . . . 8 7 . . . . . . 0 7 . . . . . . . . 1 . . . . . . . 1 6 . . . . . . . . . 1 . . . . . . 2 5 .
156 SCSI Connections SCSI Restrictions SCSI Restrictions This section describes the SCSI restrictions that apply to your workstation in the following areas: • Cables • Connectors and Terminator • SCSI configuration constraints Cables All SCSI devices ship without cables.
157 SCSI Connections SCSI Restrictions CAUTION: SCSI cables approved by HP are designed to function within the SCSI tolerances for HP devices. Use of other cables can result in significant problems with system operation.
158 SCSI Connections SCSI Restrictions Connectors and Terminators Any narrow , SE SCSI device connecting to the system must use a 50-pin high-density thumb screw connector on the end connecting to the system board.
159 SCSI Connections SCSI Restrictions SCSI Configuration Constraints Y ou are limited to the number of same-type SCSI devices per system. Before adding another SCSI device, determine if the system can support the addi- tional device.
160 SCSI Connections SCSI Restrictions CAUTION: Do not mix narrow , single-ended SCSI, fast, wide differential SCSI, or ultra, wide- SE SCSI peripherals on the same SCSI bus. Fast, Wide, Differential SCSI Bus Configuration Constraints FWD SCSI does not work with either SE SCSI.
161 SCSI Connections Determining SCSI Bus Length Determining SCSI Bus Length This section helps you to determine the total length of the narrow , single- ended SCSI bus, the fast, wide differential SCSI bus and ultra, wide single- ended SCSI bus.
162 SCSI Connections Determining SCSI Bus Length If you have problems, call your designated service representative. Subtotals: __________ + __________ T otal SCSI Bus Length = __________ (T otal narrow , single-ended SCSI bus length not to exceed 6 meters [19.
163 SCSI Connections Determining SCSI Bus Length Fast, Wide Differential SCSI Bus Length Follow these instructions to calculate your total bus length for the fast, wide differential SCSI bus on your system, using T able 25. 1 List all of your internal fast, wide differential SCSI devices in the first column.
164 SCSI Connections Determining SCSI Bus Length If you have problems, call your designated service representative. Subtotals: ______________ + ________ T otal Fast, W ide Differential SCSI Bus Length.
165 SCSI Connections Determining SCSI Bus Length Ultra, Wide, Single-Ended SCSI Bus Length Follow these instructions to calculate your total bus length for the ultra, wide, sin- gle-ended SCSI bus on your system, using T able 26. 1 List all of your internal Ultra, Wide SCSI devices in the first column.
166 SCSI Connections Determining SCSI Bus Length If you have problems, call your designated service representative. Subtotals: ______________ + ________ T otal Ultra, W ide SE SCSI Bus Length = ______________ (T otal ultra, wide SE SCSI bus length not to exceed total of 3 meters [9.
167 SCSI Connections Assigning SCSI Device IDs Assigning SCSI Device IDs Before assigning a SCSI device ID to your drive, you need to check your existing SCSI device IDs.
168 SCSI Connections Assigning SCSI Device IDs 2 You can tell which SCSI IDs are currently in use by looking under the H/W Path heading. The listing 8/16/5 scsi is the built-in SCSI bus controller. For devices connected to the built-in SCSI bus, such as disks, the fourth number is the SCSI ID for that device.
169 SCSI Connections Assigning SCSI Device IDs CAUTION: Do not use SCSI device ID 7 for any device. It is reserved for the built-in SCSI bus controller .
170 SCSI Connections Assigning SCSI Device IDs Fast, Wide Differential SCSI IDs (C160/C180/C200 Upgrades) Before assigning a SCSI device ID to your drive, you need to check your SCSI device IDs. T o check which SCSI device IDs are available and assign an ID to your device, follow these instructions which use T able 28.
171 SCSI Connections Assigning SCSI Device IDs Ultra, Wide SCSI IDs Before assigning a SCSI device ID to your drive, you need to check your SCSI device IDs. T o check which SCSI device IDs are available and assign an ID to your device, follow these instructions which use T able 29.
172 SCSI Connections Connecting to the SCSI Ports Connecting to the SCSI Ports This section describes how to connect to the system SCSI ports (narrow sin- gle-ended and fast, wide differential or ultra, wide single-ended).
173 SCSI Connections Connecting to the SCSI Ports NOTICE: It is necessary to put a terminator on empty SCSI connectors on the backpanel, or the last device connected to the SCSI bus. T erminators are shipped with the system. Do mix Fast, W ide and Ultra, W ide-SE terminators.
174 SCSI Connections Connecting to the SCSI Ports.
175 D The Boot Console Interface.
176 The Boot Console Interface This appendix describes the different features of the boot console interface and how to use them. It presents the information in the following sections: • Boot console.
177 The Boot Console Interface Boot Console Interface Features Boot Console Interface Features There are times when you want to interact directly with the hardware of your workstation before it boots the operating system.
178 The Boot Console Interface Boot Console Interface Features ------ Main Menu ----------------------------------------------------- Command Description ------- ----------- BOot [PRI|ALT|<path>.
179 The Boot Console Interface Boot Console Interface Features ------ Configuration Menu -------------------------------------------- Command Description ------- ----------- AUto [BOot|SEArch] [ON|OFF.
180 The Boot Console Interface Boot Console Interface Features ------ Information Menu ---------------------------------------------- Command Description ----------- ----------- ALL Display all system.
181 The Boot Console Interface Boot Console Interface Features ------ Service Menu -------------------------------------------------- Command Description ------- ----------- ChassisCodes [<proc>.
182 The Boot Console Interface Accessing the Boot Console Interface Accessing the Boot Console Interface T o access the boot console interface, follow these steps: NOTICE: This procedure should be done by a system administrator . 1 Close any files and applications on your workstation.
183 The Boot Console Interface Booting Y our Workstation Booting Your Workstation Usually , you start your workstation by turning it on and waiting for HP-UX to boot automatically .
184 The Boot Console Interface Booting Y our Workstation Answering yes ( y ) causes the ISL to be loaded from the specified device. After a short time, the following prompt appears on your screen: ISL> ISL is the program that actually controls the loading of the operating system.
185 The Boot Console Interface Searching for Bootable Media Searching for Bootable Media T o list devices that contain bootable media, follow the directions in “Access- ing the Boot Console Interfac.
186 The Boot Console Interface Resetting Y our Workstation Resetting Your Workstation T o reset your workstation, follow the directions in “Accessing the Boot Con- sole Interface” earlier in this .
187 The Boot Console Interface Displaying and Setting Paths Displaying and Setting Paths A path is the hardware address of a device that is attached to the I/O system of your workstation.
188 The Boot Console Interface Displaying and Setting Paths The paths are displayed in Mnemonic Style Notation, as shown in T able 31. T o display the current setting for a particular system path, fol.
189 The Boot Console Interface Displaying and Setting the Monitor T ype Displaying and Setting the Monitor Type Y our system ships from the factory preset to use a monitor with a specific resolution and frequency .
190 The Boot Console Interface Displaying and Setting the Monitor T ype When a dual display graphics adapter (an adapter which has two video out- put connectors) is installed, the video connector on the left (when looking at the system from the rear) is graphics( N A) and the video connector on the right is graphics( N B) .
191 The Boot Console Interface Displaying and Setting the Monitor T ype Setting the Monitor Type Y ou can set the monitor type for a graphics adapter by entering the follow- ing: Configuration Menu: Enter command > monitor graphics( n ) tt Where n is the number of the graphics adapter and tt is the monitor type.
192 The Boot Console Interface Displaying and Setting the Monitor T ype T o set the monitor type for graphics(0) to monitor type 2, enter the follow- ing; Configuration Menu: Enter command > monitor graphics(0) 2 Configuration Menu: Enter command > monitor graphics(0) 2 This will take effect on the next reboot.
193 The Boot Console Interface Displaying and Setting the Monitor T ype Setting the Monitor Type at Power On If you replace your workstation’s monitor with a different monitor type, and do not set t.
194 The Boot Console Interface Displaying and Setting the Monitor T ype Changing the Console to External Terminal In the event that your console stops displaying to your graphics device, use the fol- lowing procedure to display to console to an external terminal: 1 Turn system power off.
195 The Boot Console Interface Displaying the Current Memory Configuration Displaying the Current Memory Configuration The following sample screen output using the memory command shows: first, a mem.
196 The Boot Console Interface Displaying the Current Memory Configuration Memory Information Sample 1 The following sample shows the memory information when memory mod- ules are properly installed a.
197 The Boot Console Interface Displaying the Current Memory Configuration Memory Information Sample 2 The following sample shows the memory information when memory mod- ules are not properly installed and configured. In this sample the memory module in memory slot 1A is missing.
198 The Boot Console Interface Displaying the Status of the System I/O Displaying the Status of the System I/O The IO command lets you identify all built-in I/O devices and optional I/O devices installed in the option slots. It is available in the Information Menu.
199 The Boot Console Interface Setting the Auto Boot and Auto Search Flags Setting the Auto Boot and Auto Search Flags auto boot and auto search are variables stored in your workstation’ s non- volatile memory . (Nonvolatile memory retains its contents even after power is turned off.
200 The Boot Console Interface Setting the Auto Boot and Auto Search Flags Autosearch searches for devices in the following order: Primary boot path Alternate boot path Built-in fast, wide SCSI device.
201 The Boot Console Interface Displaying and Setting the Security Mode Displaying and Setting the Security Mode The SECure flag is a variable stored in non-volatile memory .
202 The Boot Console Interface Displaying and Setting the Fastboot Mode Displaying and Setting the Fastboot Mode When fastboot is enabled (set to on ), your workstation does a quick check of the memory and skips I/O interface testing, and processor and cache self- testing during its power-on self tests.
203 The Boot Console Interface Displaying the LAN Station Address Displaying the LAN Station Address It is sometimes necessary to supply a LAN station address of your worksta- tion to other users.
204 The Boot Console Interface Configure and Display LAN Settings Configure and Display LAN Settings The LanConfig command configures and displays the current LAN settings. The C180, C200, C240 and C360 systems support 10Base-T , 100Base-T and AUI standards.
205 The Boot Console Interface Configure and Display LAN Settings Configuration Menu: Enter command > LanConfig AUI NOTE: The LAN setting defaults to LAN-TP(RJ45). If that setting fails, the system tries the LAN-AUI setting. Also note that the new lan configuration settings take effect at the next BOot or SEArch command.
206 The Boot Console Interface Displaying System Information Displaying System Information The all command allows you to display the system’ s processor revision and speed, cache size, memory size, flag settings, and the boot and console paths.
207 The Boot Console Interface Displaying PIM Information Displaying PIM Information The pim command allows you to display the most recent PIM information for the specified fault type.
208 The Boot Console Interface Displaying PIM Information.
209 Glossary absolute pathname The full pathname of a file, including all the directories leading to it, starting with the root direc- tory (“/”) and ending with the filename itself. See also file , filename , path- name . access permissions Settings that allow a user or group of users to read, write, or execute files.
210 Glossary and flat spots arranged in a continuous spiral track, which is read at a constant speed. CD-ROM drive A random-access, read-only, mass-storage device that uses removable CD-ROM discs. The drive contains a semiconductor laser for read- ing data optically and an embedded con- troller with a SCSI interface.
Glossary 21 1 key while pressing another key. cpu See Central Processing Unit . CRX color graphics Expanded graph- ics capability offering 24-plane color, 24-plane Z-buffered color, or 48-plane Z-buffered color capability. current directory See current work- ing directory .
212 Glossary stations. A diskless workstation boots from its partner workstation. See also disked workstation , node , partner node , workstation . double click To press and release a mouse button twice in rapid succession. drag To press and hold down a mouse button while moving the mouse (and the pointer on the screen).
Glossary 213 file server A workstation whose prima- ry task is to control the storage and re- trieval of data from hard disks. Any number of other workstations can be linked to the file server in order to use it to access data. file system The organized set of files and directories on a hard disk.
214 Glossary iconize To turn a window or shell into an icon. See also icon . Initial System Loader The program that actually controls the loading of the operating system. input device Any of several pieces of hardware equipment used to give infor- mation to a system.
Glossary 215 menu bar An area at the top or bottom of a window that contain the titles of the pull-down or pop-up menus for that ap- plication. minimize button In HP VUE, a push button on the window frame that turns a screen into an icon. See also icon , iconize .
216 Glossary path The hardware address of a device that is attached to the I/O system of your workstation. pathname A series of names separated by slashes that describe the path of the operating system from some starting point in the network to a destination ob- ject.
Glossary 217 give the system to execute a utility pro- gram or shell script. See also shell script , utility program . shell script A file that contains com- mands that the system can interpret and run in a shell. shutdown The process of taking the system from multi-user state to system administration state.
218 Glossary non-client programs into believing they are running in their favorite terminal. When not running programs or execut- ing operating system commands, termi- nal windows display the command-line prompt. See also HP Visual User Envi- ronment .
Glossary 219 eration of windows on the HP VUE Workspace. The Workspace Manager is a special Window Manager. See also Window Manager . workstation A compact, graphics-ori- ented computer having high speed and high memory capacity. A workstation usually includes a keyboard, a monitor, and a system unit.
220 Glossary.
Index 221 Symbols $HOME,, 213 A absolute pathname,, 209 access permissions,, 209 active window,, 209 ANSI,, 209 archiving data listing files,, 56 restoring files,, 56 saving to a cassette,, 55 archivi.
222 Index double click,, 212 drag,, 212 drive,, 212 drop,, 212 E EISA option board installing,, 136 EISA slots displaying status,, 198 EISA,, 212 electrostatic discharge (ESD) precatuions,, 94 emissio.
Index 223 data cassettes,, 58 diskettes,, 70 output device,, 215 output window,, 215 P parent directory,, 215 partner node,, 215 password,, 215 path displaying,, 187 setting,, 188 path,, 187, 216 pathname,, 216 permissions,, 216 PID,, 216 PIM information,displaying,, 207 pointer,, 216 pointing devices, 21 problems 802.
224 Index.
Een belangrijk punt na aankoop van elk apparaat Compaq C180 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Compaq C180 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Compaq C180 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Compaq C180 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Compaq C180 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Compaq C180 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Compaq C180 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Compaq C180 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
