Gebruiksaanwijzing /service van het product 132.24607 van de fabrikant Craftsman
Ga naar pagina of 20
Operator's Manual RIDER COOLING SYSTEM Model No. 132.24607 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. IMPORTANT: For replacement parts or assembly questions call 800-320-MIST. • Safety • Assembly • Operation • Maintenance • Troubleshooting Sears, Roebuck and Co.
SAFETY RULES .................................... 2 HARDWARE CONTENTS ..................... 3 CARTON CONTENTS ............................ 4 ASSEMBLY .......................................... 5 OPERATION ........................................ 14 MAINTENANCE .
A ...... iii!iii iii_jiiiii ii_iiHiiiTi ¸ii -¸ ? B f ii // H S D E REF. QTY. DESCRIPTION A 2 Hex Bolt, 5/16"-18 x1-1/4" B 2 Flat Washer, 7/8" OD C 4 Cap Screw, 5t16-!8" x 3/4&quo.
AA. Power Unit BB. Misting Nozzle Assembly CC. Mounting Bracket DD. 9/16" Drill Bit BB /.
Tools Required ½" Socket Wrench w/Extension Allen Wrenches Power Drill Adjustable Wrench Mounting Power Unit To Tractor NOTE: If there is a 2 or 3 bin bagger installed on your tractor, you will need to remove the bagger from the tractor before proceeding.
Once all bolts have been installed, tighten all nuts using allen wrench and socket on both bolts and nuts, Mounting Misting Nozzle Assembly to Tractor The rider cooling system misting assembly is designed to be installed on the tractor's dash. Some tractors come equipped with rider cooling system mounting locations.
Using supplied 9/16" drill bit (DD), drill hole through the dash at the bottom of the mounting location. Use caution not to damage anything in the engine com- partment while drilling hole. Step 2 • Install rubber washer (H) onto the misting arm assembly (BB), by sliding over hoses and threaded section until seated against mounting flange.
Step 3 IMPORTANT: If you have not already done so, you must disconnect the negative (-) termi- nal of the battery before completing the next steps. • Repeat with the remaining dash adapter nut (F) until seated on bottom surface of the nut already installed.
Connecting Power Unit to Misting Arm Assembly Step 1 • Locate supply lines and power connector at the power unit (AA) and uncoil to full length. Step 2 • When the supply lines have exited the underside of the tractor body, feed the supply lines and power connector along tractor chassis into engine compartment.
Step 3 • Locate BLACK supply tube from power unit and BLACK supply tube from misting nozzle assembly. • Remove protective caps from the BLACK supply tube and filter attached to the BLACK tube. • Connect BLACK supply tube from misting arm assembly to the filter installed on the BLACK supply tube from the power unit.
Step 3 • Connect power unit's female connector to Maintenance Minder. Step 4 • From inside the engine compartment, locate tractor power supply connector. NOTE: The tractor power supply connector will resemble the female connector supplied with the power unit.
Finalizing System Installation Step 1 • Review the illustration below to familiarize yourself with the suggested locations of the routing clips (G) EACH SIDE OF DASH SUPPORT IMPORTANT: Do not kink hoses exiting the power unit.
Step 2 • Using a supplied cable tie (J) organize any excess length of supply tubes and stow behind battery (or along fuel tank if equipped). Secure supply tubes to electrical supply lines of tractor at convenient locations to prevent line damage during tractor operation.
KNOW YOUR RIDER COOLING SYSTEM Read this owner's manual before operating. Compare the illustration below with your rider cooling system to familiarize yourself with the various features and their locations. POWER SWITCH Controls the power to the system's pump.
HOW TO START YOUR RIDER COOLING SYSTEM • With the tractor key in "ON" position, toggle power switch on unit to "ON" posi- tion. NOTE: It is normal to experience a delay from the time the system is turned on to the deliv- ery of mist from the nozzle.
CUSTOMER RESPONSIBILITIES VIA1 NTENANCE SCHEDULE sill in dates as you complete "egular service Sh eck for loose fasten ers Slean Exterior Zmpty Water Tank Clean Basket Filter Sor_dition Water Tank :_eplace Ah-fWater Filters Read and follow the maintenance schedule and the maintenance procedures listed in this section.
• Empty water tank completely, replace cap, and run system to evacuate all wa- ter in supply lines. • Store misting nozzle assembly by folding over dash of tractor. • Ensure the power switch on the power unit is in the "OFF" position. • Clean debris from venting on rear of power unit.
NOTES: ]8.
NOTES: ]9.
For expert troubleshooting and home solutions advice: manage home www,managemyhome,com For repair- in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling syste.
Een belangrijk punt na aankoop van elk apparaat Craftsman 132.24607 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Craftsman 132.24607 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Craftsman 132.24607 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Craftsman 132.24607 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Craftsman 132.24607 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Craftsman 132.24607 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Craftsman 132.24607 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Craftsman 132.24607 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
